Gira KNX 5001 Series User manual

Pushbutton sensor 4 Komfort
Pushbutton sensor 4 Komfort, 1-gang
Order no.: 5001 ..
Pushbutton sensor 4 Komfort, 2-gang
Order no.: 5002 ..
Pushbutton sensor 4 Komfort, 4-gang
Order no.: 5004 ..
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. During installation and cable routing, comply with the regulations and
standards which apply for SELV circuits.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Front view (Figure 1)
Figure1: Device components 4-channel
(a) Operating rockers
(b) Status LED
(c) Push-button for future applications
1...8 Push-buttons assignment and status LED
1 / 6
32401902 10866576 16.10.2019

Pushbutton sensor 4 Komfort
Rear view (Figure 2)
Figure2: Device components - rear side
(d) Device connection terminal for remote sensor
(e) Locking screws
(f) Opening for removing the KNX connection terminal with screwdriver
(g) Device connection terminal KNX
3 System information
This device is a product of the KNX system and complies with the KNX directives. Detailed tech-
nical knowledge obtained in KNX training courses is a prerequisite to proper understanding.
The function of this device depends upon the software. Detailed information on loadable soft-
ware and attainable functionality as well as the software itself can be obtained from the manu-
facturer´s product database. Planning, installation and commissioning of the device are carried
out with the aid of KNX-certified software. The latest versions of product database and the tech-
nical descriptions are available on our website.
4 Intended use
– Operation of loads, e.g. light on/off, dimming, Venetian blinds up/down, 1 byte values, 2
byte values, brightness values, temperatures, calling up and saving light scenes
– Mounting in appliance box according to DIN 49073
5 Product characteristics
– Push-button sensor functions switching, dimming, Venetian blind, value transmitter, scene
extension, 2-channel operation and controller extension adjustable
– Controller extension with operating mode selection, forced operating mode switch over,
presence function and setpoint shift
– Status LED - optionally red, green, blue, yellow, cyan, orange, violet, white - adjustable
per button
– LED functions orientation lighting, alarm signalling and night reduction can be set separ-
ately
– Brightness of LED adjustable and switchable while in operation
– Disable or function switch-over of all or of individual button functions possible with dis-
abling function
– Scene control up to 8 scenes with 8 scene outputs each
– Temperature measurements optionally with device internal sensor, wired sensor to the
connection terminal and external sensor connected via communication object
– Room humidity measurement with internal device humidity sensor
2 / 6
32401902 10866576 16.10.2019

Pushbutton sensor 4 Komfort
– Integrated bus coupling unit
6 Operation
Depending on the programming, a control rocker can have up to two functions assigned to it
(left, right). Operation is carried out by short or long pressing the buttons and depends on the
specific function.
6.1 Examples for operating various standard applications
￭ Switch: Short press on button.
￭ Dim: Long press on the button. The dimming process ends when the button is released.
￭ Move Venetian blind: Long press on button.
￭ Stop or adjust Venetian blind: Short press on button.
￭ Set value, e.g. brightness or temperature setpoint: Short press on button.
￭ Open scene: Short press on button.
￭ Save scene: Long press on button.
￭ Execute channel 1: Short press on button.
￭ Execute channel 2: Long press on button.
￭ Operate controller extension: Short press on button.
7 Information for electrically skilled persons
7.1 Fitting and electrical connection
DANGER!
Mortal danger of electric shock.
Cover up live parts in the installation environment.
Mounting and connecting the device (Figure 3)
Figure3: Fitting the device
(a) Operating rockers
(e) Locking screws
(h) Supporting frame
3 / 6
32401902 10866576 16.10.2019

Pushbutton sensor 4 Komfort
(i) Programming button
(j) Push-button sensor
(k) Box screws
The device should be used in an air-tight appliance box. Otherwise temperature and hu-
midity reading can be negatively influenced by draughts.
￭ Mount supporting frame (h) in the right orientation on an appliance box.
Note the TOP marking.
Use the enclosed box screws (k).
￭ Pull off start-up rockers from push-button sensor.
The push-button sensor is delivered with start-up rockers. The operating rockers suitable
for the push-button sensor must be ordered separately (see accessories).
￭ Connect push-button sensor (j) to the KNX (g) using KNX connecting terminal (red = +,
black = -).
￭ Optional: Connect remote sensor (see accessories) to device connection terminal (d).
￭ Attach push-button sensor (j) onto the supporting frame (h).
￭ Screw push-button sensor (j) with the integrated locking screws (e) onto supporting frame.
Connection torque max. 0.8 Nm.
￭ Optional: Cover up the locking screws (e) with the labels supplied with the rocker set (only
for the 2-gang and 4-gang device variants).
Push-button sensor can be put into operation.
Programming the physical address before operating rockers mounting.
￭ Snap on the operating rockers (a).
Device is ready for operation.
7.2 Commissioning
Programming the physical address and application program
Project design and commissioning with ETS from 5.6 onwards.
The programming button (i) is located under the topmost operating rocker.
Precondition: The device is connected and ready for operation.
The topmost operating rocker is dismantled.
￭ Activating Programming mode: push the programming button (i).
The status LED 1 and 2 flash red. Programming mode is activated.
￭ Programming the physical address.
The status LED 1 and 2 return to their previous state. Physical address is programmed.
￭ Programming the application program.
All status LEDs are switched off while the application program is programmed. As soon as
the programming is successfully completed, the status LEDs carry out their parameterised
function.
When the application program is discharged and the bus voltage is connected, all status
LEDs initially light up white. Whenever a button is actuated, the respective illuminated
status LED changes colour in (white → red → green → blue → yellow → cyan → orange → vi-
olet → white → ...).
8 Technical data
KNX
KNX medium TP256
4 / 6
32401902 10866576 16.10.2019

Pushbutton sensor 4 Komfort
Commissioning mode S-mode
Rated voltage DC 21 ... 32 V SELV
Current consumption KNX 8 ... 19 mA
Connection mode KNX Standard device connection terminal
Connecting cable KNX EIB-Y (St)Y 2x2x0.8
Protectionclass III
Mechanism
Loosening torque locking screws Max. 0.8 Nm
Connection cable remote sensor (see accessories)
Cable type extension NYM-J 3×1.5 or
J-Y(St)Y 2×2×0.8
Total length remote sensor line max. 50 m
Ambient conditions
Ambient temperature -5 ... +45 °C
Storage/transport temperature -20 ... +70 °C
9 Accessories
Individually labelled rocker sets are available from the Gira inscription service www.bes-
chriftung.gira.de.
Rocker set, 1-gang for pushbutton sensor 4 Order no. 5021 ..
Rocker set, 1-gang, inscribable, for pushbutton sensor 4 Order no. 5031 ..
Rocker set, 2-gang for pushbutton sensor 4 Order no. 5022 ..
Rocker set, 2-gang, inscribable, for pushbutton sensor 4 Order no. 5032 ..
Rocker set, 4-gang for pushbutton sensor 4 Order no. 5024 ..
Rocker set, 4-gang, inscribable, for pushbutton sensor 4 Order no. 5034 ..
Remote sensor Order no. 1493 00
10 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your re-
sponsible salesperson (specialist trade/installation company/electrical specialist trade). They will
forward the devices to the Gira Service Center.
5 / 6
32401902 10866576 16.10.2019

Pushbutton sensor 4 Komfort
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-191
www.gira.de
[email protected]
6 / 6
32401902 10866576 16.10.2019