Gira KNX IP-Router User manual

GIRA
Info
KNX IP-Router
Installation Instructions
KNX IP-Router 9/07 Page 1 of 4
System information
This device is a product of the Instabus-KNX system
and complies with KNX directives.
Detailed technical knowledge obtained in Instabus
training courses is a prerequisite to proper under-
standing.
The functionality of this device depends upon the soft-
ware.
Detailed information on loadable software and attain-
able functionality as well as the software itself can be
obtained from the manufacturer’s product database.
Planning, installation and commissioning of the unit is
effected by means of KNX-certified software.
An updated version of the product database and the
technical descriptions are available in their latest ver-
sion on our Internet homepage.
Function
Description
• Rail-mounted device for installation in distributions
• Interconnection of KNX lines via local area data
networks (LAN) based on the use of the IP protocol
(IP = Internet Protocol)
• Use as line / area coupler (filter tables)
• Interconnection of KNX devices with PCs or other
DP devices via IP (use as data interface)
• Power supply via external power supply unit
(accessories)
• Transmission of KNX system failure message to
the PC
• Electrical separation between KNX and IP network
KNX IP-Router Order no.: 1030 00
Safety instructions
Electrical equipment must be installed and fitted
by qualified electricians only.
Failure to observe the instructions may cause
damage to the device and result in fire and other
hazards.
Supplying the IP router with power from the KNX
unit (‚non-choked‘ output) is not permitted. Risk
of grounding the safety extra-low voltage of the
KNX system.
Use safety transformers in acc. with EN
61558-2-6 or doorbell transformers in acc. with
EN 61558-2-8.
These instructions are part of the product and
must be left with the customer.
iDepending on application, access require-
ments, data security and data volume it may
be advisable to install independent network
paths for individual services using the IP net-
work.

GIRA
Info
KNX IP-Router
Installation Instructions
KNX IP-Router 9/07 Page 2 of 4
Status LED (Figure 1)
(1) LINE (yellow) data reception on KNX line
(2) RUN (green) ready for operation
(3) LK (green) Ethernet link signal (lit up during
active connection with the IP net-
work)
(4) RX (yellow) Ethernet receive signal (lit up/
flashing on reception of valid IP
telegrams)
(5) TX (yellow) Ethernet transmit signal (lit up/
flashing during active transmis-
sion to the IP network)
Information for qualified electricians
Fitting and electrical connection
Fitting in fixed installations indoors, in dry rooms,
power distributions or small housings with DIN rail.
Observe the temperature range. Ensure sufficient
cooling.
• Install by snap-fastening on mounting rail in acc.
with EN 60715. Mounting position see figure 2.
• Connect the external power supply to terminal (7).
Recommendation: Use white/yellow terminal.
• Connect the KNX line by means of the black/red
bus terminal (8).
• Connect the IP side with RJ45 connector plugged
into RJ socket (6).
DANGER!
Risk of electric shock on accidental contact with live parts in the fitting environment.
Electric shocks can be fatal.
Before fitting, disconnect the supply voltage and cover up live parts in the working environment.

GIRA
Info
KNX IP-Router
Installation Instructions
KNX IP-Router 9/07 Page 3 of 4
Commissioning
Physical address and application software
Use as
line coupler: Physical address x.y.0.
Use as
area coupler: Physical address x.0.0.
Use as
data interface: Physical address x.y.z.
When used as line/area coupler, no other lin/area
coupler must be operated in the same segment.
Commissioning software from ETS2 version 1.2 on-
wards.
• Press programming key (9).
Programming LED (10) is illuminated.
• Assign the physical address.
The programming LED is extinguished.
• Note the physical address on the device label (11).
• Download the application software, filter tables, pa-
rameters etc.
iWiring example see figure 3.
iThe IP address (e.g. 255.173.27.39) is loaded
as parameter togehter with the application
software into the device or automatically as-
signed by a DHCP service.

GIRA
Info
KNX IP-Router
Installation Instructions
KNX IP-Router 9/07 Page 4 of 4
Technical data
KNX medium: TP1
Mode of commissioning: S-Mode (ETS)
KNX supply: DC 21…30 V SELV
KNX current rating: typically 10 mA
KNX connection: Bus terminal
External supply:
Voltage: AC/DC 12...30 V
Power consumption: max. 800 mW
(25 mA at DC 24 V)
Connection: Connecting terminal
IP communication: Ethernet 10BaseT
(10 Mbit/s)
IP connection: RJ45 socket
Supported protocols: ARP, ICMP, IGMP,
UDP/IP, DHCP, KNXnet/IP
(Core, Routing, Tunneling,
Device Management)
Ambient temperature: -5 °C ... +45 °C
Storage temperature: -25 °C ... +70 °C
Fitting width: 36 mm (2 modules)
Weight: 100 g
Accessories
Gira power supply unit 24 V AC, order no. 1024 00
Acceptance of guarantee
We accept the guarantee in accordance with the corresponding legal provisions.
Please return the unit postage paid to our central service department giving a brief description of the
fault:
Gira
Giersiepen GmbH & Co. KG
Service Center
Dahlienstrasse 12
D-42477 Radevormwald
Gira
Giersiepen GmbH & Co. KG
Postfach 1220
D-42461 Radevormwald
Telefon: +49 / 21 95 / 602 - 0
Telefax: +49 / 21 95 / 602 - 339
Internet: www.gira.de
Table of contents
Other Gira Network Router manuals