D-Link DIS-300G Series User manual

Quick Installation Guide
1
DIS-300G Series Managed Industrial Gigabit
Ethernet Switch
Quick Installation Guide
Overview
The Managed Ethernet Switch solutions are designed for supporting standard industrial
applications. Managed switches are easier to prioritize, partition, and organize user’s
network, providing a more reliable and better quality services.
Package Checklist
Please verify the box contains the followingitems:
Item Quantity
Management Ethernet switch 1
Wall-mount plates 2
DIN-Rail CLIP 1
M3 Screws (for the wall mount plates & DIN CLIP) 4
DC power terminal block 1
RJ45 Ethernet port Dust Cover Some
SFP Ethernet port Dust cover Same as SFP port number

Quick Installation Guide
2
Safety Instructions
When a fiber connection is removed during installation, testing, servicing or anactive fiber is
broken, ocular exposure to optical energy may be potentially hazardous, depending on the
laser output power.
The primary hazards of exposing laser radiation from an optical-fiber communication systems
are:
● Damage to eyes from accidental exposure to a beam emitted by a laser source.
● Damage to eyes from viewing the connector that attaches to a broken fiber or an
energized fiber.
If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
DIN-Rail Mounting
Mounting steps:
1. Screw the din-clip with screws in the accessory kit.
2. Hook the unit onto the din-rail.
3. Push the bottom of the unit towards the din-rail until it locks in place.
2
3

Quick Installation Guide
3
Wall Mounting
Mounting steps:
1. Screw the wall-mount brackets with screws in the accessory kit.
< This graph is for all DIS-300G series >
Ethernet Interface (RJ45 Ethernet)
The switch provides two types of Ethernet interfaces: electrical (RJ45) and optical (SFP)
interfaces.
Connecting the Ethernet interface via RJ45:
● To connect the switch to a PC, use straight-through or cross-over Ethernet cables,
● To connect the switch to an Ethernet device, use UTP (Unshielded Twisted Pair)
or STP (Shielded Twisted Pair) Ethernet cables.
The pin assignment of RJ-45 connector is shown in the following figure and table.
Pin Assignment
PoE Assignment
(for DIS-300G-8PSW/DIS-300G-
14PSW only)
1,2 T/Rx+,T/Rx- Positive VPort
3,6 T/Rx+,T/Rx- Negative VPort
4,5 T/Rx+,T/Rx- X
7,8 T/Rx+,T/Rx- X

Quick Installation Guide
4
Ethernet Interface (Fiber, SFP)
For both 100/1000 Mbps fiber speed connections, the SFP slots are available. The SFP slot
accepts the fiber transceivers that typically have an LC connector.
The fiber transceivers have options of multimode, single mode, long-haul or special-
application transceivers.
DANGER:
Never attempt to view optical connectors that might be emitting laser energy.
Do not power up the laser product without connecting the laser to the optical
fiber and putting the dust cover in position, as laser outputs will emit infrared
laser light at this point.
Connecting Power Terminal Block
The switch can be powered from two power supplies (input range 12V – 58V). Insert
the positive and negative wires into V+ and V- contacts on the terminal block
respectively and tightenthe wire-clamp screws to prevent the wires from being
loosened.
Note:
The DC power should be connected to a well-fused power supply.
DIS-300G12SW

Quick Installation Guide
5
DIS-300G-8PSW/DIS-300G-14PSW
Alarm Relay and Ground
The alarm relay output contacts are in the middle of the DC terminal block connector as
shown in the figure below.
The alarm relay out is “Normal Open”, and it will be closed when detected any predefined
failure such as power failures or Ethernet link failures.
The relay output with current carrying capacity of 0.5A @ 24 VDC

Quick Installation Guide
6
Console Connection
The Console port is for local management by using a terminal emulator or a computerwith
terminal emulation software.
● DB9 connector connect to computer COM port
● Baud rate: 115200bps
● 8 data bits, 1 stop bit
● None Priority
● None flow control
To connect the host PC to the console port, a RJ45 (male) connector-to-RS232 DB9
(female) connector cable is required. The RJ45 connector of the cable is connected to the
CID port of the switch; the DB9 connector of the cable is connected to the PC COM port.
The pin assignment of the console cable is shown below:

Quick Installation Guide
7
Connect & Login to Managed Switch
1. Connecting to the Ethernet port (RJ45 Ethernet port) of Managed Switch.
2. Factory default IP: 10.90.90.90
3. Login with default account and password.
Username: admin
Password: admin
CLI Initialization & Configuration
1. Connecting to the Ethernet port(RJ45 Ethernet port) of Managed Switch
2. Key-in the command under Telnet: telnet 10.90.90.90
3. Login with default account and password.
Username: admin
Password: admin
4. Change the IP with commands listed below:
CLI Command:
enable
configure
terminal
interface vlan 1
ip address xxx.xxx.xxx.xxx
xxx.xxx.xxx.xxx exit

Quick Installation Guide
8
LED STATUS INDICATIONS
LED Name Indicator /color Condition
P1/P2 On Green P1/P2 power line has power
Off P1/P2 power line disconnect or does not have power supplied
Alarm On Red Ethernet link fails, alarm or power failure alarmoccurs
Off No Ethernet link fails and no power failure alarm
Copper port
Link/Act
On Green Ethernet link up but no traffic isdetected
Flashing Green Ethernet link up and there is traffic detected
Off Ethernet link down
Copper port
Speed On Yellow A 1000Mbps connection is detected
Off No link, a 10Mbps or 100 Mbps connection is detected
SFP port
Link/Act On Green Ethernet link up
Off Ethernet link down
SFP port
Speed On Yellow SFP port speed 1000Mbps connection isdetected.
Off No link or a SFP port speed 100Mbps connection isdetected
DIS-300G-8PSW/DIS-300G-14PSW only
RR
(Ring Role) On Green One of 3 Ring group is enabled and is Master role.
Off Ring is slave role
RS
(Ring Status) On Green Ring fail happen and detected
Off No ring fail detected
PoE On Yellow PoE is detected
Off No link
Additional Information
You can refer to the user manual or visit http://support.dlink.com/ for more support.
Online Support
If there are any issues that are not in the user manual, please visit http://support.dlink.com/
which will direct you to your appropriate local D-Link support website.
Warranty Information
Visit http://warranty.dlink.com/ to view the D-Link Warranty information.
Ver. 1.00(EU)2017/12/04