Glen Dimplex Xpelair XPP Quick reference guide
USE & CARE INSTRUCTIONS
Model: XPP TOWER COOLING FAN
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE USE
A brand of Glen Dimplex UK Limited, trading as Glen Dimplex Heating & Ventilation
IMPORTANT SAFETY WARNINGS
Failure to comply with the warnings listed below may
result in serious injury, risk of fire or electric shock.
This product should be used only in accordance with the specifications outlined in this manual.
1. Do not use this appliance until the base is properly assembled and it is standing upright
supported on and by its base only, do not use lying down or lying at an angle against anything.
2. Never immerse the appliance in water or other liquids; never spray liquids on the appliance.
3. Never operate the appliance if a cable or connector has been damaged, after the appliance
has malfunctioned or if the appliance was dropped or otherwise damaged in any way.
4. Electric appliance may only be repaired by qualified personal, improper repair work can be a
source of considerable danger for the users.
5. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience or knowledge if they
have been given supervision or instruction concerning the use of the appliance in a safe way
and understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
6. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
7. Disconnect the appliance from mains power whenever it is not in use and before moving or
relocating it.
8. Operate the appliance only at the voltage specified on the rating label.
9. Only use the appliance inside (indoors) and only for the purpose it was designed.
10. To avoid the risk of damage or a dangerous situation do not use this appliance or position any
part of it near to heat, open flame, cooking appliances or any heating appliance.
11. Do not place heavy objects on the appliance or any object against the product when operating.
12. Do not use the appliance in an area where there are likely to be flammable or explosive fumes
or liquids.
13. Only use the appliance on a stable and level surface.
14. Unplug the appliance before cleaning.
15. To unplug the appliance do not pull on the mains cable, grip the plug at the wall outlet and pull
carefully.
16. Should the appliance fail to operate please check the fuse in the plug is intact and confirm that
the circuit breaker / fuse at your distribution board is operating before contacting the
manufacturer or service agent.
☆TECHNICAL SPECIFICATION
Specification Details - XPP
Symbol
Value
Unit
Maximum Fan Flow Rate
F
9.2
m³/min
Fan Power Input
P
32.3
W
Service Value
SV
0.3
(m³/min)/W
Standby Power Consumption
PSB
0.64
W
Fan Sound Power Level
LWA
64
dB(A)
Maximum Air Velocity
c
4.1
meters/sec
Rated Voltage
V
220-240
V
Rated Frequency
Hz
50
Hz
Measurement Standard for Service
Value
IEC 60879:1986
☆HOW TO ASSEMBLE THE BASE
Carefully remove the split base and the tower fan from its packaging.
Pass the power cord between the two halves of the split base at the
centre and fit the two halves’ together by lining up the overlap bosses
on the back half (with the cable exit) with their sockets on the other
half and dropping into place and pressing together.
Bring the assembled base up to the bottom of the tower and line up
the small pillar on the top of the raised centre of the base with the
matching hole in the base socket location of the tower fan, pull the
cable through fully so it doesn’t interfere with them fitting together.
Take the 4 large screws provided and pass them through the holes
in the circular bosses (located around the central hub on the underside
of the base) into the bottom of the tower, screw fix them firmly in place.
Carefully fit the cable through the slot to the back side of the hub and
then through the guide location channel at the outside of the circular
base to exit level with the base through the channel at the back.
Your XPP Cooling Fan is now ready to stand and operate.
☆NB - THIS IS NOT A FAULT
If the fan speed varies randomly including stopping and starting automatically you have
selected either NATURAL or NIGHTIME Variable Blower Mode which simulate different
breezy conditions. To de-select this mode you must press the button to change back to
constant blowing mode, please refer to section ‘d’ following on how to change modes. To
run in constant speed mode only use the button to select the speed you require, please
refer to section ‘b’ following.
☆OPERATING INSTRUCTIONS
All of the functions of this fan can be controlled from the “soft-touch buttons on the unit’s control
panel” or by use of “the wireless remote control”.
The LED display screen on the control panel of the product illuminates to display what function you
have selected when the fan is operating.
a. Turning on/off the fan: Gently press “ON/OFF” button on the “soft-touch button control
panel” or the “wireless remote control”.
b. Adjusting and Selecting Speed: 3 constant speeds can be selected by pressing the button
either on the control panel or on the remote. Each time you press this button the speed will cycle
from I to II to III and back to ‘I’ again. Where “I” = Low speed, “II” = Medium speed and “III” =
High speed.
c. Oscillating function: Your product can oscillate in an arc from left to right and back again
continuously thus circulating the air flow over a wider area. To start the tower fan oscillating
simply press the oscillation button on the control panel for less than 2 seconds or the
button on the remote and the symbol will light up on the control panel. Press this button a
second time to stop the oscillation.
d. Variable Blower Function Selection: Your product can be set to automatically vary the speed
output to simulate different breezy conditions. It will normally run in constant blowing mode at
whichever speed you selected (see “b.” above). To select a variable blower speed function you
can simply press the button on the remote or press and hold the dual control button on
the control panel for at least 2 seconds. There are two selections available:
1. The first mode activated will be the ‘natural breeze’ selection and the symbol will light up
on the control panel. In this mode the fan speed will continuously and randomly vary
between speed levels (including off) to simulate variable wind conditions.
2. Pressing the on the remote a second time or pressing and holding the dual control
button on the control panel again for at least 2 seconds will activate ‘night time’ selection
and the symbol will light up on the control panel. In this mode the fan speed varies
automatically between speed levels (including off) at a less noticeable rate than the ‘natural
breeze’ selection.
- Pressing the button a third time for more than 2 seconds will change it back to constant
normal blowing mode.
e. Runback Timer function: The product can be set to switch off automatically after running for
one of four user selectable runback periods i.e. 1 hr, 2 hr, 4 hr or 8 hr.
To activate the runback function just simply press the timer button
- Press once and the timer is set to 1hr runback
- Press twice and the timer is set to 2hrs runback
- Press 3 times and the timer is set to 4hrs runback
- Press 4 times and the timer is set to 8 hrs runback
- Press a 5th time and the timer function is switched off.
REMOTE CONTROL
Your remote control comes complete with a CR2025 3V battery fitted.
To replace the battery simply remove the securing screw, unclip and
remove the battery cover on the back and replace the battery, then
carefully refit the cover, snap into place and refit the securing screw.
☆CLEANING：
Disconnect from the mains before attempting to clean the appliance.
Clean the air inlet and outlet regularly with a soft damp (not wet) cloth as these areas accumulate
dust normally during use. Do not use petrol or solvents or caustic or abrasive cleaning agents as
these will destroy the surfaces of the heater.
☆RECYCLING –Important - Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please recycle this product responsibly to promote the sustainable
re-use of material resources. To recycle your used product, contact the retailer where the
product was purchased or use your local authority recycling facilities where these exist.
Batteries should be disposed of or recycled in accordance with WEEE Directive 2012/19/EU.
Packaging should be recycled where possible.
Warranty
What does an Xpelair Warranty cover?
Xpelair products deliver reliable service for normal, household use in domestic settings. All Xpelair
products are individually tested before leaving the factory.
If you are a consumer and you experience a problem with your Xpelair product, which is found to be
defective due to faulty materials or workmanship within the Warranty Period, this Xpelair Warranty
will cover repair or - at the discretion of Xpelair –replacement with a functionally equivalent Xpelair
product.
The Xpelair Warranty Period is one year from the date of purchase of your Xpelair product, or the
date of delivery of the product, if later. The Xpelair Warranty is conditional upon you providing the
original purchase receipt as proof of purchase. Please therefore retain your receipt as proof of
purchase.
If you do experience a problem with your Xpelair product please call the Helpline on +44 [0]344 879
3588 or email [email protected]. For ROI please email
product, its serial number and a description of the fault which has occurred. You can find the model
number and serial number for your Xpelair product on the heaters side. Once we receive your
information and proof of purchase we will contact you to make the necessary arrangements.
If your Xpelair product is not covered by this Xpelair Warranty there may be a charge to repair your
product. However, we will contact you for agreement to any charges before any chargeable service
is carried out.
What is not covered by an Xpelair Warranty?
The Xpelair Warranty does not cover any of the following:
• Any fault or damage to your Xpelair product due to faulty materials or workmanship occurring
outside the one year Warranty Period.
• Any fault or damage occurring to any pre-owned Xpelair product or to any other equipment or
property.
• Accidental damage to your Xpelair product or damage to your Xpelair product from external
sources (for example, transit, weather, electrical outages or power surges).
• Fault or damage to your Xpelair product which is:
• Not due to faulty materials or workmanship or which is due to circumstances outside
Xpelair’s control.
• Caused by use of your Xpelair product for anything other than normal domestic household
purposes in the country where it was purchased.
Important
• Caused by any misuse, abuse or negligent use of the Xpelair product, including but not limited to
any failure to use it in accordance with the Operating Instructions supplied with the product.
• Caused by any failure to assemble, install clean and maintain your Xpelair product in accordance
with the Operating Instructions supplied with the product unless this was carried out by Xpelair or its
authorised dealers.
• Caused by repairs or alterations to your Xpelair product not carried out by Xpelair service
personnel or its authorised dealer(s).
• Caused by use of any consumables or spare parts for your Xpelair product which are not Xpelair -
specified.
Terms and Conditions
• The Xpelair Warranty is valid for Xpelair from the date of purchase of you Xpelair product from a
recognised retailer in the country of purchase and use, or the date of delivery of the product if later,
always provided the original receipt has been retained and is produced as proof of purchase.
• You must provide to Xpelair or its authorised agents on request the original receipt as proof of
purchase and - if required by Xpelair - proof of delivery. If you are unable to provide this
documentation, you will be required to pay for any repair work required.
• Any repair work under the Xpelair Warranty will be carried out by Xpelair or its authorised
dealer(s) and any parts that are replaced will become the property of Xpelair Any repairs performed
under the Xpelair Warranty will not extend the Warranty Period.
• Any replacement of your Xpelair product by Xpelair during the Warranty Period will start the one
year Warranty Period afresh from the date of delivery of the replacement Xpelair product to you.
• The Xpelair Warranty does not entitle you to recovery of any indirect or consequential loss or
damage including but not limited to loss or damage to any other property.
• The Xpelair Warranty is in addition to your statutory rights as a consumer and your statutory rights
are not affected by this Xpelair Warranty.
__________________________________________________________________________________________________________________________________
CE This product complies with all the required European product safety, Electromagnetic compatibility and
environmental standards. It is fully compliant with the LVD, EMC, RoHS and Eco design directives.
Contact Xpelair
If you have any questions about what the Xpelair Warranty covers and does not cover or how to claim under
the Xpelair Warranty, please contact us using the information below.
Millbrook House,
Grange Drive,
Hedge End,
Southampton,
S030 2DF
Telephone: +44 [0]344 879 3588
Email: customer.services@glendimplex.com
Republic of Ireland Tel.: 01 842 4833
Website: www.xpelair.co.uk
A brand of Glen Dimplex UK Limited, trading as Glen Dimplex Heating & Ventilation.
© Glen Dimplex. All rights reserved. Material contained in this publication may not be reproduced in whole or in part without prior permission in writing of Glen
Dimplex.
GDHV Group Ltd reserves the right to modify the content of these instructions, at any time and without prior notice
XPP-IM-190923 Issue 4
Table of contents
Other Glen Dimplex Fan manuals
