Gliderol Glidermatic GTS 2000 User manual

GTS2K07-2
Tilt and Sectional Overhead Door Operator
Installation Instructions and
Owners Manual

Important lnformation
Please keep these instructions safe for later reference.
Dear Customer,
We thank you for your decision to purchase this
garage door operator.
Attention:lmportant instructions for safe installation:
This garage door operator is designed only for the
automatic operation of spring-balanced up-and-over
doors and sectional doors for domestic use only.
The manufacturer is exempt of any guarantee
obligations and product liability, when the customer
undertakes improper installation work or arranges for
same to be carried out contrary to the installation
guidelines provided. Any changes carried out, only
with the manufacturer's prior approval.
Incorrect installation could give rise to serious
injuries. Please follow all installation instructions
carefully!
In the interests of human safety it is vital that all
these instructions be followed in full.
Keep hand transmitters well out of the reach of
children.
Garages without a second entrance require an
emergency release,the function of which must be
checked once a month.
Do not allow anyone to hang bodily from the pull
cord of the manual release.(Danger of bending)
Always cover up the operator before drilling.
Electrical installation on site must comply with
the relevant safety regulations (240 V AC, 50 Hz).
Electrical connections must only be carried out by
a qualified electrician!
Batteries and light bulbs are not covered by the
guarantee.
Any further processing must ensure that the national
regulations governing the operation of electrical
equipment are complied with. Moreover, We shall
accept no responsibility for the inadvertent or
of the door, the accessories and the garage door
operator.
The operator is not suitable for heavy duty,applications
i.e. doors that can no longer be opened or closed by
hand. Or where this is only possible with great
difficulty. Before installing the operator,the door must
move easily by hand.
Before installing the operator, ensure that the
mechanics of the entire door system are in perfect
working order.Before the operator is fitted,any of the
door's mechanical locks and latches must be
immobilised.
The door operator may not be used if repair or
adjustment work is to be carried out.
The construction of the garage ceiling must be such,
that safe, secure anchoring of the operator is
guaranteed.
Permanently installed controls (e.g. buttons or similar
devices) should be installed within sight of the door.
Keep the controls away from any moving parts and at
a height of at least 1.5 metres.It is important that they
be installed well out of the reach of children.Warning
negligent operation or improper maintenance/servicing
2
notices about the trap risk must be
permanently fixed in a conspicuous
place or near the permanently
installed buttons used to actuate
the operator.

Maintenance Instructions:
We advice you to make a complete check of the door
system once annually. It is recommended that you
have your door and operator serviced by a qualified
technician once every 24 months.
Important lnformation
3
The operator is designed for use in dry environments
and therefore must not be installed exposed
to weather.
In carrying out the installation work, the
applicable regulations regarding working safety
must be complied with.
Make sure that the cable of the operator's manual
release cannot get caught up in the roof carrier
system or in any other protruding parts on the vehicle
or the door.
within the travelling range of the door. Initial function
checks, as well as programming or extending
the remote control, has to be carried out from inside
the garage.
Before carrying out any work on the operator,
disconnect the mains plug.
how to use the operator safely and properly.
Demonstrate and test the automatic reversing as well
as the manual release. With the garage door open,
check the function of the manual release once a
month.
Attention: a door with weak, broken or
defective springs or an inadequately counterbalanced
door can quickly close on its own accord.
Only operate the door, when the door's range of travel
is within your field of vision. Wait until the door has
come to a complete halt. Move only, when the door
has come to a complete standstill. Before driving in or
out of the garage, make sure that the door is fully
opened and has ceased travelling.
Always ensure, that no persons or objects are located
Instructions for using the operator:
* DANGER *
All persons using the door system should be instructed
Please keep these instructions safe for later reference.
max.150N/m

Technical Data
4
Power Supply
Force
Running time
Speed without load
Clearance for operator
Drive mechanism
Overall length
Approx. Weight
Max. door opening(3m shaft)
Optional 3.6m shaft available
Max. door size
Circuit board
240V 50Hz
700 N
max. 30%
approx. 14cm/ sec.
40mm
chain
3210 mm
~18kg
2400mm
18sqm
NGTS-2001 REV:A

Installation lnstructions
5
Contents
Itemised Description of Parts:
1.L-Section Foot Mounting Bracket.
2.BoomerangArm.
3.Boomerang ExtensionArm.
4.Hinge Bracket.
5.Thrust Block & PusherArm.
6.Shaft.
7.Lintel Bracket.
8.Shaft Bracket.
9.Chain Tensioning Block.
10.Powerhead.
11.Manual Release Cable.
12.Chain Location Clip.
13.Transmitter.
14.Dual Purpose Transmitter Bracket.
15.Chain.
16.Shaft Support Bracket.
1 2 3
4 5
6789
10 12 13 14
15
16
11

6
Installation lnstructions
Deactivate all garage door locks
Tilt door
Sectional Door
Min:40mm
Min:40mm

Installation lnstructions
7
Tilt door Sectional Door
Before starting to determine which type of door you have, this background depicts an ideal
installation and can be scale.
It is essential the door header be substantial as nearly all the force generated by the opener is
concentrated via the header bracket. Determine the centre of the door and continue this vertical
line through the header. Open the door and find the highest point to which the top of the door
reaches, using an appropriate straight edge and level. Transfer this height to the header. Allow
from 8-10mm clearance between the drive shaft and the door. Place the bottom of the header
bracket at the height determined, fixing with the screw/s supplied. Headroom requirements and
the need to avoid obstruction sometimes make it necessary to move the bracket higher.
MIDDLE OF THE DOOR
Min7 5mm:
90
。
90
。

8
Installation lnstructions
Insert carriage in shaft.
Install chain as direction shown around tensioning pulley.

Installation lnstructions
9
Link chain at correct length.
Insert tensioning pulley to end of shaft
Middle of the shaft

10
Installation lnstructions
Remove drive sprocket protection lid. Slide shaft and chain into powerhead chassis and then
place chain over powerhead drive sprocket.
Place powerhead on the garage floor, being careful not to damage or scratch the paintwork
and attach shaft end bracket assembly to header bracket using nuts and bolts supplied.
approx. 5mm
middle of the shaft

Installation lnstructions
11
Fit drive sprocket protection lid as per diagram.
Curved arm should not be used on tilting type doors. For sectional door, mount door bracket
on top of door panel, ensuring a tek screw is fitted to centre stile.

12
Installation lnstructions
Raise powerhead and support on step ladder. Raise the door to open position, align the drive
shaft with the point market at the top of the door. Exact alignment is essential.

Installation lnstructions
13
To secure the opener support powerhead in the manner shown using brackets supplied or fix
directly to roof as in diagrams (a) & (b).

14
Disengage Auto Operation
Test shaft in manual operation
Glide carriage forward and attach pusher arm to door bracket, as shown on page 15.
Test Manually
Unlock
Unlock Main Chain
Lever

Disengage Auto Operation
15
Middle of the door
Middle of the door

16
Disengage Auto Operation
Manual Release

Limit Setting
17
Option 1:PCB
Procedures :
(i) Press S3 to initiate learning mode (3 beeps)
(ii) Press and hold S2, release when door reaches TOP position
(iii) press S3 to confirm TOP position (2 beeps)
(iv) Press and hold S2, release when door reaches BOTTOM position
(v) Press S3 to confirm BOTTOM position (2 beeps)
(vi) Controller will initiate checking process for both TOP and BOTTOM positions
PCB
GRD-2000RX REV:B

18
Limit Setting
Option 2: Transmitter
Procedures
(i) Press and hold S1 + S3 for two seconds to initiate learning mode (3 beeps)
(ii) Using buttons S2 & S3, locate TOP position
(iii) Press S1 to confirm TOP position (2 beeps)
(iv) Using buttons S2 & S3, located BOTTOM position
(v) Press S1 to confirm BOTTOM position (2 beeps)
(vi) Controller will initiate checking process for both TOP and BOTTOM positions
Note:
1.All steps must be carried out to restart learning process. For example, if a mistake is made
when learning the TOP position after confirming, all of the subsequent steps must be carried
out prior to relearning the TOP position again.
2.When setting the TOP position, an overload sensing feature is built in to prevent damaging the
control gear.
S1
S2
S3

SENSOR CONNECTION DIAGRAM
19

20
Transmitter Key and Code Setting
Refer to PCB
Key Setting (.)
from the following:-
Single door installation (A)
The above jumper configuration will allow Key 1 on the
hand transmitter to be programmed.
The jumpers are located on the Control Box
Printed Circuit Board. (Key 1. Key 2. Key3).
Jumper configuration for transmitter Key 1 only
Jumper configuration for transmitter Key 2 only
Jumper configuration for transmitter Key 3 only
Choose the Transmitter key configuration Key1.Key2.Key3
Key 1
Note:
Door 1
Door 2
Door 3
Two or Three door installation
Code Setting
Once the Key configuration is set you can now program
in the security code from your hand transmitter (s)
Press the learn code key once (8)
Learn LED Indicator will light (8A)
Press the hand transmitter Key1 that will operate
the door eg: for single door installation (A) you would
press Key 1
Learn LED (8A) will go out
The hand transmitter is now programmed





Multiple Hand Transmitters
Repeat the above instructions for any subsequent Hand
Transmitters.
The Control Module has enough memory for up to 10
individual Hand Transmitters.
press and hold the learn code key (8)* for 5 seconds.
If a transmitter is lost or stolen please erase the
memory and re-learn any spare or new transmitters.
If more than 10 handsets are learnt the FIFO (First In First
Out) system applies ie first Hand transmitter code learnt
will be deleted and replaced by the last Hand Transmitter
code learnt.
Deleting Hand Transmitters From Memory
All transmitter codes held in the memory have
been erased.
Note:
Battery Type 12V (A23)(ALKALINE BATTERY)
The battery should be replaced every 12 months
To reassemble:-
Hold front cover as per drawing
Insert membrane, then Printed Circuit Board
Locate back of case and screw together




Insert 12Volt (A23) Battery negative towards screw
Key Ring Transmitter
Back
PBC
lnside of
Front
Cover
(This will locate as per drawing)