Global Industrial 293068 User manual

1
Electronic Window Air Conditioner
062019
User's manual Manual del usuario Manuel de l'utilisateur
Customer Service
US: 1-800-645-2986
Servicio de atención al Cliente
US: 1-800-645-2986
Service à la clientèle
Canada: 888-645-2986
•Plug into a grounded 3 prong outlet.
•DO NOT remove the ground prong.
•DO NOT use a plug adapter.
•DO NOT use an extension cord.
•Unplug the air conditioner before servicing
• Two people are recommended to lift and install the unit.
•Refrigerant R32 is used. Contact a qualified service
technician for maintenance of the refrigerant.
The electrical ratings for your air conditioner are listed on
the model and serial number label located on the front,
left side of the unit (when facing front).
Recommended Ground Method
For your personal safety, this air conditioner must be
grounded. This air conditioner is equipped with a 3 prong
power supply cord and a grounded plug. To minimize the
possibility of electrical shock, the cord must be plugged
into a 3 prong outlet and grounded in accordance with
all local codes and ordinances. If a 3 prong outlet is not
available, it is the customers responsibility to have a
proper 3 prong outlet installed by a qualified electrician.
It is the customers responsibility:
•To contact a qualified electrician
•To assure that the electrical installation is
adequate and in conformance with the National
Electrical Code, ANSI/NFPA 70 - latest edition, and
all local codes and ordinances.
LCDI Power Cord and Plug
This air conditioner is equipped with an LCD (Leakage
Current Detection and Interruption) power cord that is
required by UL. This power supply cord contains state-
of-the-art electronics that sense current leakage. If the
cord is damaged and leakage occurs, power will be
disconnected from the unit.
The test and reset buttons on the LCDI plug are used to
check if the plug is functioning properly. To test the plug:
1. Plug power cord into a grounded 3 prong outlet.
2. Press RESET (on some units a green light will turn on).
3. Press the TEST button, the circuit should trip and cut
all power to the air conditioner (on some units a green
light will turn off).
4. Press the RESET button for use. You will hear a click
and the A/C is ready for use.
Model 293068 6,000 BTU, Cool Only, 115V
WARNING
Read all instructions before use.
To reduce the risk of fire, electric
shock, or injury to persons when
using this appliance, follow the
following precautions:

TABLE OF CONTENTS
ELECTRICAL REQUIREMENTS ...................................................................................
INSTALLATION HARDWARE .......................................................................................
INSTALLATION & ASSEMBLY INSTRUCTIONS ...........................................................
........................................................................
TROUBLESHOOTING .................................................................................................
1
USING YOUR AIR CONDITIONER ................................................................................ 6
8
CARE ANDMAINTENANCE ......................................................................................... 9
10
2
3

1
7
8
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do Not remove the ground prong.
Do Not use an adapter.
Do Not use an extension cord.
Failure to follow these instructions can
result in electrical shock, fire, or even
death.

2
INSTALLATION HARDWARE INCLUDED
NOTE: Save carton and these Installation Instructions for future reference. The carton is the best way to store unit during winter or when not in use.
(Only for E-Star models)

3
23" to 36"
584 mm to 914 mm
14 1/2" min
(368mm)
OFFSET
STOOL
SILL
INTERIOR
WALL
EXTERIOR
WALL
FIG. 1
6 84
Head
INSTALLATION & ASSEMBLY INSTRUCTIONS (CONT.)
Packaging
Foam
Unit
14½

4
8
5
INSTALLATION & ASSEMBLY INSTRUCTIONS (CONT.)
Place the air conditioner on the sill with the bottom mounting rail
against its back edge. Center the air conditioner and close the
window securely behind the top mounting rail. The air conditioner
should be slightly tilted to the outside area. NOTE: Check that air
conditioner is tilted back approximately ¾” to 1”. (Tilted about 3° to 4°
downward to the outside). If, after proper installation, condensation
does not drain from the overflow drain hole during normal use, adjust
slope. (See FIG. 6 & FIG. 7) (Suggested to keep a downward slope to
let accumulated rain water to drain out from the backside of the unit's
bottom.)
Once the air conditioner is installed, extend both the left and
the right accordion panels to the width of the window.

Place the frame lock between the extended accordion
panels and the window sill as shown in FIG. 9. Screw a
3/4" (19 mm) locking screw through the frame lock and
into the window sill. (FIG. 10)
5
Head
FIG. 13
FIG. 14
FIG. 11 FIG. 12
FIG. 9 FIG. 10
INSTALLATION & ASSEMBLY INSTRUCTIONS (CONT.)
For added insulation, cut the supplied insulation foam to the
width of the window. Insert the foam between the window
sashes to prevent outside air and object from getting into
the room. (See FIG. 14)
1. Turn the air conditioner off and disconnect the power cord.
2. Remove the sash seal from between windows and
unscrew sash lock.
3. Remove the screws installed through the frame and frame
lock.
4. Slide the side panels out of the frame.
5. Keeping a firm grip on the air conditioner, raise the sash
and carefully tilt the air conditioner backwards to drain any
condensate water in the base of the unit. Be careful not to
spill any remaining water while lifting the unit from window.
6. Store parts WITH the air conditioner in the original box or
in an area with low humidity.

6
1.
Shows the set temperature.
Operation modes are: Cool, Dry, Fan, and Auto.
Time is displayed using the timer setting.
Digital Display:
3
6
1
2
4
5
9
8
7
.
3.
4.SleepPress the SLEEP button, all of the
display lights will turn off after a while, but the
sleep light is always on. In themode, the air
conditioner will automatically adjust the
temperature and fan speed to make the room
more comfortable during the night. The set
temperature will automatically change every
30-60 minutes and at most change six times until
O
the set temperature is 81 or 82 .F

7
6. Turn the air conditioner on and
off.
Power Button:
Press the FAN SPEED button
to select the fan speed. In COOL MODE you can
choose the following settings: HI, MED, LO, or
AUTO. In Fan MODE you can choose from HI,
MED, and LO.
9.Fan Speed Button:
5.Eco Button:
10.
Use the horizontal wheels
to control horizontal airflow and the air deflectors
to control vertical airflow.
Directional Louvers:
horizontal wheel airdeflector air deflector
Whenthe Filter Check light is off,
it is to press the Filter Check button.
the Filter Check light is on, can turn off
by pressing the Filter Check button. After
fan motor works for 500 total hours, the Filter
Check light will turn on to remind the user to clean
the filter.
Filter Button:
7.
Use these buttons on the control
panel and remote to set the Timer.
Timer Off: The timed stop is programmed by
pressing TIMER button. Set the rest time by
pressing the button or until the rest
time displayed is to your demand then press
TIMER button again.
Timer On: When the unit is off, press TIMER
button at the first time, set the temperature with
pressing the button or . Press TIMER
button at the second time, set the rest time with
pressing the button or . Press TIMER
button at the third time, confirm the setting,
Note: It can be set to automatically turn off or on
in 0.5-24 hours. Each press of the
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.
To cancel the set function, press the TIMER
button again.
then it
will show on the display.
8.TimerButton:

8
USING YOUR REMOTE CONTROL

9
CARE AND MAINTENANCE
Clean your air conditioner to keep it looking new,
minimize dust build up and for optimal performance.
The air filter should be checked at least once a
month to see if it needs cleaning. Trapped particles
and dust can build up in the filter and may
decrease airflow as well as cause the cooling coils
to accumulate frost.
To clean the air filter, power the unit off and:
Wash the filter using liquid dish soap or mild detergent
and warm water. Rinse the filter thoroughly. Gently
shake the filter to remove excess water.
NOTE:
Power off and unplug the air conditioner to
prevent shock or fire hazard. The cabinet and
front panel of the air conditioner may be dusted
with an oil-free cloth or wiped down with a
damp cloth in a solution of warm water and
mild liquid soap. Rinse thoroughly with a damp
cloth and wipe dry.
Never use harsh cleaner, wax or polish on the
front of the cabinet.
To store the air conditioner when it is not in use for
an extended period of time, remove it carefully from
the window according to the installation instructions
and cover it with plastic or place it in the original
box. Remove the batteries from the remote before
storing.
FIG.15
FIG. 15

10
.
Check that there is no damage to the
plug fuse / circuit breaker box and
replace the fuse or reset the breaker.
.
The temperature setting may not be
set correctly.
Battery Size: AAA - NOTE: Do not mix old and new batteries or different types of AAA batteries.
.
.
See "The Air Conditioner is
Freezing Up" below.

11
NOTE
Ahighlyrecommendedtroubleshootforanyissueingeneralconsistsofturningoffunitandunpluggingfor5minutes. It is also
recommended to try another wall outlet. For further assistance, contact Consumer Services at 888-433-6254 or 888-4DENALI.
The air conditioner is not correctly
pitched towards the outside.
For proper water drainage, make
sure the air conditioner is slightly
pitched downwards from the front of
the unit to the rear (Refer to
installation instructions).
.
.
.