Global Sat GH-209 User manual

GH-209 GPS BLE 6.23.15 SL

Table of Contents
ABOUT GPS......................................................................................................................................................................... 3
ABOUT 3ATM WATER RESISTANCE ....................................................................................................................................... 3
ABOUT IPX7 WATER RESISTANCE.......................................................................................................................................... 3
WHAT’S INCLUDED .............................................................................................................................................................. 4
GETTING START................................................................................................................................................................... 4
CHARGE YOUR WATCH ........................................................................................................................................................ 6
CONFIGURE YOUR WATCH FOR FIRST USE ............................................................................................................................ 8
CONFIGURE YOUR WATCH BEFORE WORKOUT ..................................................................................................................... 8
GO FOR A WORKOUT .........................................................................................................................................................13
CHECK YOUR HEART RATE IN TIME MODE ...........................................................................................................................1
REVIEW YOUR WORKOUT...................................................................................................................................................16
REVIEW YOUR DAILY WALKS ...............................................................................................................................................18
DEVICE INFORMATION .......................................................................................................................................................18
DEVICE CARE......................................................................................................................................................................19
TROUBLESHOOTING ...........................................................................................................................................................20
GET MORE INFORMATION..................................................................................................................................................21
APPENDIX..........................................................................................................................................................................21
1

Thank you for purchasin the Globalsat GH-209 3 in 1 Trainin Watch! Let’s learn more about this excitin
product.
About GPS
GPS stands for Global Positionin System. For 3D fix, we need at least 4 satellites. Normally the accuracy of
GPS under open sky that means no tall buildin and clear sky is within 10 meters per second. Therefore, if
the device shift 10 meter at that second, the device may show 36 Km/h instant speeds.
Nowadays, the GPS consumer product has built in adjust al orithm and assisted method to extend
capability of GPS.
About 3ATM Water Resistance
Suitable for daily use. Splash/rain resistant. NOT suitable for showerin , bathin , swimmin , snorkelin ,
water related work and fishin .
R EMARK : NOT SUITABLE FOR DIVING
About IPX7 Water Resistance
Suitable for indoor/outdoor use in the presence of rain, snow or brief splashes of water. NOT suitable for
any immersion of more than 1 meter, re ardless of duration of immersion, or any immersion of more than
30 minutes, re ardless of depth of immersion.
IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS
A LWAYS CONSULT YOUR PHYSICIAN BEFORE YOU BEGIN OR MODIFY ANY EXERCISE PROGRAM
1To prevent risk of fire, chemical burn, electrolyte leak, and/or injury from the unit’s internal
Lithium-polymer battery:
1.1 Do not attempt to remove the case-back or exterior shell of the unit, or to remove its
non-user-replaceable battery.
1.2 Do not leave the unit exposed to a heat source or a hi h-temperature location (such as in the sun
or in an unattended vehicle). To prevent dama e, store the unit out of direct sunli ht.
1.3 Do not puncture or incinerate the unit.
2

1.4 When storin the unit for an extended time, keep it in the 32 to 77°F (0 to 25°C) temperature
ran e.
1.5 Char e the unit only within the 32 to 113°F (0 to 45°C) temperature ran e.
1.6 Do not operate the unit outside the 14 to 140°F (-10 to 60°C) temperature ran e.
1.7 Contact your local waste disposal department to properly recycle or dispose of the unit or its
battery.
2Use only the char in cable supplied.
3This unit is not a medical device and is not recommended for use by persons with serious heart
conditions. Always consult your physician before be innin or modifyin an exercise pro ram.
4Do not attempt to read the unit’s display while movin : this is unsafe and distractin , and could result
in an accident or collision. Read the display only when you can safely do so.
5Avoid extreme shock and harsh treatment, because it can de rade the life of the product.
6Avoid press the key under water.
7Do not store the watch where prolon ed exposure to extreme temperatures can occur, because it can
cause permanent dama e.
What’s Included
1Globalsat 3 in 1 Trainin Watch GH-209
2Clipper type Char er
3Quick Start Guide
Getting Start
For first use, please follow these eneral steps to et started:
1Char e your watch.
2Confi ure your watch.
3Pair BLE HRM belt (optional)
4Go for a WORKOUT
5Get Run on your smart phone
6Upload your WORKOUT to Run
7Upload your WORKOUT to Sports4U.pro
8Get more information
3

Download gRun
Keys
Power
Backlight
Push to turn backlight on / off.
Hold to turn watch on / off.
Under workout mode, hold to finish and save the workout,
after workout saved will turn off the watch.
Start
Pause
Save
Push to enter menu, select a highlighted menu, or confirm to
start a run or setting and returns to previous screen.
Push to bypass searching for H M or fixing GPS.
Under workout mode, push to pause the run, push again and
hold to finish and save the workout.
Back
esume
Push to return to previous menu.
Push to pause under workout
4

Up
Previous
Increase
PPG Heart ate Measure
Push to display seconds, step count and distance walked in mini
page under Time Mode.
Push to moves up in a screen, highlight previous item in a menu.
Push to switch page up under Workout Mode.
Hold to turn on/off heart rate measuring under Time Mode
Down
next
Decrease
Push to display seconds, step count and distance walked in mini
page under Time Mode.
Push to moves up in a screen, highlight next item in a menu.
Push to switch page down under Workout Mode.
Icons
H
Heart rate measuring status. Turn solid when Heart ate under measuring, flashing if
still searching for heart rate signal. Stop flashing in 5 min.
Battery
Displaying battery status, icon flashing and buzzer alert when battery down below
15%.
Icon flashing and buzzer alert again when battery down below 5%, and watch
automatically turn off.
Alarm
Alarm icon will display when clock configured.
Steps
Number after this icon will display steps count or switch by (Up or Down) to total
workout distance.
GPS
GPS status, stay solid when location fixed, flashing when device under positioning. Stop
searching by 30 sec, and recording by pedometer.
Phone
Phone connection status. Stays solid when connection alive, flashing and beep when
connection broken. Icon will turn off when the watch enter workout mode.
Charge your watch
Before you start use the watch, fully charge the battery using your computer or a wall outlet as a
power source.
5

1Attach the char in cable clip to the watch so the clip’s pins ali n with the contacts on the back of the
watch.
2Turn off the watch before char in may reduce char in time less than 2 hours.
3Select a power source:
3.1 Computer: Insert the free end of the char in cable into a powered USB port on your computer.
3.2 Wall outlet: Insert the free end of the char in cable into a USB power adapter, then insert the
adapter into a wall outlet.
4Let the battery char e at least 3 hours. The flashes durin char in or the battery icon in the
center of screen turns solid static if your turn off as below.
When you connect the watch to a power source, the watch will turn on in charging screen. Charge the watch until the battery icon
stays still as above.
Maximizing battery life
Use this procedure to maximize the time range of your watch’s rechargeable battery:
1Use your watch without rechar in until the last battery indicator se ment disappears and the empty
indicator be ins flashin . If the watch display oes blank, you can still proceed with this process as
lon as the display has been in the state for no more than one or two days.
2Fully char e the watch battery for at least 3 hours, until the battery level indicator no lon er blinkin .
6

3Repeat this procedure twice more.
N TE: Repeat this procedure every two months if the watch is not used or recharged regularly.
Configure your watch for First Use
The first time you power on the watch, you will set up language, units, date/time, time format and
personal profile.
1Press and hold for more than 2 sec to power on the watch. The watch then be ins the
first-time setup process.
1.1 If first-time setup does not be in, press to o to the main menu, then select SETTINGS >
ABOUT > RESET > OK! The watch then enters factory reset process and turn power back on
automatically.
2Follow the instructions shown in the watch’s display, usin , , and .
Configure your watch before workout
This section intends to assist you to customize your GH-209. The sequence of items is referring to the
actual watch screen except PAIR due to its importance we move it to independent session.
1. GENERAL
1.1 Lan ua e
1.1.1 Currently offer En lish only. We will provide more lan ua e options for your choice in near
future.
1.2 ALARM
1.2.1 When you set up a time and turn alarm ON, you will receive buzzer alerts when time is up.
Also the vibration alert if you turn on alarm vibration (SETTINGS > GENERAL >
VIBRATION > ALARM > ON).
1.3 DATE, TIME
1.3.1 To choose 24H or 12H system.
1.3.2 Confi ure your local date and time.
1.4 SOUND
1.4.1 Turn ON in KEY, buzzer will beep when you push buttons.
1.4.2 Turn ON in WORKOUT, buzzer will beep in a unique sound when you push to GO,
PAUSE for a run.
1.5 VIBRATION
1.5.1 Vibration alert for ALARM, TARGET and NOTICE.
1.5.2 Turn ON for ALARM to vibrate when set up time is up.
1.5.3 Turn ON for TARGET to vibrate when you out of tar et zone that you’ve indicted.
7

1.5.4 Turn ON for NOTICE to vibrate when a notification received from your phone (Incomin
Calls, Messa e or Phone Lost).
1.6 UNITS
1.6.1 To choose En lish system (Inch/lb) or Metric system (cm/K ).
1.7 DOZE MODE
1.7.1 Enable for power savin . The screen will doze whenever it stays idle (no key interrupt) for
total 5 min.
1.7.2 Screen should wake up when motion detected.
2. TARGET (Tar et Zone)
2.1 Default value is OFF that has no tar et zone alert durin your workout.
2.2 There’re HR (heart rate), PACE and SPEED to be your trainin tar et zone.
2.3 You can preset each minimum and maximum value.
2.4 Choose one of them to be your tar et zone.
2.5 Whenever you are over or lower than your confi ured tar et zone, the watch will alerts you by
buzzer and vibrator (if you turn ON in SETTINGS > GENERAL > VIBRATION > TARGET).
3. DISPLAY
3.1 GH-209 provides you 3 pa es and 1 mini pa e.
3.2 Default settin s:
3.2.1 Pa e 1: Chrono / Speed
3.2.2 Pa e2: Distance / Pace
3.2.3 Pa e3: HR / Calories
3.2.4 Mini Pa e: Time (Local time)
3.3 Selections: Chorno, Distance, Speed, Avera e Speed, Pace, Avera e Pace, Time, HR, Avera e HR,
Calories, OFF (Display empty).
3.4 Each pa e display allows you to show 2 values in your own preference.
3.5 For Mini pa e selection: Chorno, Speed, Av speed, Pace, Av pace, Time, HR, Av HR, Calories,
Lap number, OFF.
4. Auto Lap
4.1 Go SETTINGS > AUTO LAP to choose Auto Lap by DISTANCE
4.1.1 Confi ure the distance you want to automatically count the lap.
4.1.2 Once your run reach the distance you confi ured for a lap, the screen will display like below
for 4 seconds and o back to the pa e you’ve confi ured.
8

4.2 Go SETTING > AUTO LAP to choose Auto Lap by TIME
4.2.1 Confi ure the time you want to automatically count the lap.
4.2.2 Once your run reach the time you confi ured for a lap, the screen will display like below for
4 seconds and o back to the pa e you’ve confi ured.
5. USER
5.1 To set up your own wei ht, hei ht, ender and birthday for better calculations.
6. PAIR
6.1 If you have and prefer to use BLE HRM chest belt, please o (Pair BLE Heart Rate Monitor (HRM)
chest belt) for parin .
6.2 For Phone parin , please o (Pair with your phone).
7. CALI (Calibrate distance accumulation to calculate with your step count)
7.1 Thanks to incredible GPS accuracy, GH-209 is capable to learn your walkin distance for better
step distance.
7.2 When you enter SETTINGS > CALI by , the watch will show you to walk 400M in total to
learn your actual walkin distance.
7.3 You will see a GPS si n flashin on the screen while it’s acquired GPS
si nal, please stand still under open sky without interference (trees,
buildin s, etc…) where you can have a 400 meters to walk
throu h.
7.4 When the positionin is done, GPS icon turns solid and stays in the
top of screen.
7.5 READY? will display on the screen, push
to GO! for a walk to calibrate.
7.6 Every 10 meters, the watch will show
current distance you have reach on the
screen.
7.7 When you achieve 400 meters, the screen will show you CALI OK on the screen and return to
SETTINGS menu.
N TE: The calibration process could be failed if GPS signal lost more than 10
seconds. FAILED, PLEASE RETRY message will pop up. Go through step 7.3
to 7.7 to complete the calibration or push to leave.
9

8. About
8.1 VERSION
8.1.1 FIRMWARE
8.1.1.1 Here shows you the main firmware version. Ex. F-0GH-2X-1501152, 150115 is the
date of FW released which is 2015 Jan 15
th
.
8.1.2 BLE FW
8.1.2.1 Here shows you the BLE firmware version. Ex. F-BLE-29-1503271, 150327 is the date
of FW released which is 2015 Mar 27
th
.
N TE: To check firmware information, please refer to Get More Information.
8.2 RESET
8.2.1 Allow you to reset the watch back to factory settin .
8.2.2 Default value is DON’T!! in case incidentally tri er reset.
8.2.3 Even OK! Was pushed, double confirmation will reserve a second chance.
Pair BLE Heart Rate Monitor (HRM) chest belt
N TE: if you don’t have a BLE Heart Rate Monitor, you can skip this section.
Wear the Bluetooth Low Energy (BLE) heart rate monitor directly on your skin, just below your
breastplate. It should be snug enough to stay in place during your run.
1Wrap the strap around your chest, and connect the strap hook to the loop.
2Connect the heart rate monitor module to the strap.
3Wet the electrodes (Location A and B) on the back of the strap
to create a stron connection between your chest and the
transmitter.
N TE: Some heart rate monitors have a contact patch.
Wet the contact patch.
4Brin the watch in front of you and
ensure the transmission ran e within
(2m) of the heart rate monitor.
TIP: If the heart rate data is erratic or does not appear, you may have to
tighten the strap on your chest or warm up for 5 to 10 min.
N TE: Move away (20m) from other sensors while GH-209 is trying to
pair with your heart rate monitor
5After you put on the heart rate monitor, it is on standby and ready to send
data.
6Go to your watch, enter SETTINGS > PAIR > HR SENSOR > ON, start parin
for 60 sec. Please follow the display instruction.
10

7When you see PARIED on screen, your watch now paired and remembers this HRM belt.
Pair with your phone
1. Pair with iPhone
1.1 Turn on your watch.
1.2 Enter SETTINGS > PAIR >PHONE, Push to broadcastin for
phone pairin . You will see WAIT! and flashin on the screen.
1.3 Turn on Bluetooth in your iPhone.
1.4 Enter Run
1.5 Tap on Import which in the top ri ht corner in the Activities pa e. Run will search for GH-209.
1.6 When Run see your GH-209, tap on GH-209 and tap OK on the top ri ht corner.
1.7 There will be a number input dialo ue pop up on iPhone screen.
1.8 Meanwhile, the watch will show you a 4 di its number.
1.9 Input this number in your Run dialo ue to pair. You will see screen on watch like below. Leave
phone pair settin on your watch at ON.
2. Pair with Android phone
2.1 Turn on your watch.
2.2 Enter SETTINGS > PAIR > PHONE, Push to broadcastin for
phone pairin . You will see WAIT! and flashin on the screen.
2.3 Turn on Bluetooth in your Android phone.
2.4 Enter Run
2.5 Tap on Import which on the top ri ht corner of the Activities pa e. Run
11

will search for GH-209.
2.6 When Run see your GH-209, check on GH-209 and tap OK on the top ri ht corner.
2.7 There will be a number input dialo ue pop up on Android phone screen. Check on your watch
screen, a 6 di its number will shows. Input this number in your Android phone and tap on OK.
2.8 Watch will show you PAIRED when this process success. Leave phone pair settin on your
watch at ON.
N TE: If you switch SETTINGS > PAIR > PH NE to FF on your watch, you will need to Forget or
Unpaired device GH-209 at your phone > Settings > Bluetooth, and go through this pairing
process again.
Go for a Workout
1Hold to turn on the watch.
2Push o WORKOUT to choose either run outdoor or indoor
2.1 If you are oin to run OUTDOOR
N TE: It may take 30 to 60 sec to locate satellite signals.
2.1.1 Go outside to find open sky area and hold your position.
2.1.2 Enter WORKOUT > OUTDOOR.
2.1.3 If you never paired any HRM belt before.
2.1.3.1 The watch will start detect your heart rate by Optical
HRM and search GPS location. Optical HRM will detectin up
to 30 sec and verify with you if continue search or bypass to o ahead to start a run.
12

2.1.3.2 When watch detected your heart rate and GPS fixed, you will see READY? on the
screen. If you are ready, push to see GO! and start your run.
2.1.4 If you already have HRM belt paired and you wear on it. (Pair wireless 2.4GHz Heart Rate
Monitor (HRM) chest belt)
2.1.4.1 The watch will searchin for both GPS and HRM belt, and search HRM belt up to 20
sec and switch to optical heart rate monitor if not detect a HRM belt.
2.1.4.2 When watch connect to your paired HRM belt and GPS fixed, you will see READY? on
the screen. If you are ready, push to see GO! and start your run.
2.1.5 If GPS not yet located and/or HRM not yet connected, but you still want to ahead for a run,
push to let it search in back round.
N TE: If you don’t to run with HRM belt and you want to use ptical HRM when you start a run,
go SETTINGS > PAIR > HR SENSOR to select OFF.
2.1.6 If the watch indicates that a GPS was not fixed yet for lon , move away from any tall
13

buildin s or trees, hold your position. If you decide to o for a run anyway, you can push
to allow watch searchin on the back round. Your watch will automatically switch to
pedometer if GPS doesn’t fix within 30 sec.
2.2 If you o for INDOOR
2.2.1 Enter WORKOUT > INDOOR
2.2.2 Your watch will first search the HRM belt that you paired before for up to 20 sec. If you
didn’t pair any HRM belt before or it detected it in 20sec, then initiate optical HRM to detect
your heart rate for up to 30 sec.
2.2.3 Automatically show you READY? If HRM belt linked.
TIP: Push to see READY? for you prepare to run, Push again to see GO! and start
chrono.
2.2.4 Push to GO! for a run.
3Checkin your current workout
3.1 The stopwatch provides three pa es to display real-time workout data. Each pa e includes one or
two field and a mini pa e. (Confi ure your watch)
3.2 Durin a run, push or to travel between pa es.
4Stop and save your workout
4.1 Push to pause your workout.
4.2 Push a ain to resume the workout or hold to tri er workout savin process bar. When
the savin bar fills up, workout saved and finished.
4.3 Release before bar fills up will return to workout pause status.
Check your Heart Rate in Time Mode
N TE: You can check your current heart rate in beats per minute (bpm) whenever you want under
time mode.
1Under Time Mode, hold for few seconds.
2Heart Rate si n start flashin on the top of screen for initiate and detectin your heart rate for 40 sec.
3Checkin your heart rate for 60 sec. You can hold for another few seconds to quit from heart
rate checkin .
14

4When heart rate checkin up to 60 sec, Avera e heart rate would show on the screen.
5Push to see Maximum heart rate, push a ain to see Minimum heart rate and push a ain
to o back to Time Mode.
Review your WORKOUT
In the watch:
N TE: The watch can store up to 50 workout data. You can enter HIST RY page to review each
saved data.
1Open a workout data, push and to HISTORY > WORKOUT > ARCHIVE.
2Use and to find the workout data you want to review.
3Push to see confirm open the data.
4Push to enter TRAIN INFO for detail info or to select DELETE to erase this workout data.
Data Description
XX-XX-XX Date of workout saved (YY-MM-DD, Ex. 15-06-09 = 2015 9
th
June)
Time Total elapsed time of the workout
Distance* Total distance traveled durin the workout
Av Speed* Avera e speed over the entire workout
Av Pace* Avera e minutes per mile or km
Lap* Number of laps in the workout (up to 99 laps)
Kcal Estimated quantity of calories burned durin the workout
Avera e HR Avera e heart rate per minute durin entire workout (HRM belt required)
% time in tar et
zone*
Total time of within indicated tar et zone durin entire workout. (Show in
percenta e)
*If you run without GPS fixed, these data were generated by inner pedometer throughout simulated algorithm.
In your Smart Phone
N TE: You need to download gRun on your smart phone and pair with your watch first. (Pair your
phone)
1iOS
1.1 Turn on your watch.
1.2 Turn on Bluetooth in your iPhone.
1.3 Enter gRun > Activities, your phone will connect to the watch automatically.
15

1.4 Tap on Import which on the top ri ht corner of the Activities pa e.
1.5 Tap on Paired behind GH-209 already paired, then tap OK on the top ri ht corner.
1.6 Wait for a while, you will see records list down on the data you want to upload to Run.
1.7 Now you can select your trainin record and transfer to Run. Check on the record and tap OK on
top ri ht corner.
1.8 After transmission completed, a STATUS messa e will pop up.
2Android
2.1 Turn on your watch.
2.2 Turn on Bluetooth in your Android phone.
2.3 Enter Run > Activities
2.4 Tap on Import which on the top ri ht corner of the Activities pa e.
2.5 Select your GH-209 and tap on Connect that on the top left corner. After connected, tap on
hi hli ht List and OK to fetch data list from GH-209.
2.6 Checked the data you want to transfer and tap on OK in the top ri ht corner.
2.7 After transmission completed, a STATUS messa e will pop up.
16

N TE: The List and Data transfer may take minutes, please kindly wait.
In Sport4U.pro
1You may re ister in gRun > Profile > Cloud Upload or o re ister on website Sport4U.pro .
2Go to Download to find USB driver if you are usin Windows system (not required for Mac) and install
it.
3Download and install the PC Tool.
4Connect your GH-209 to your PC or Laptop with the clip USB cable.
5Run PC Tool to upload your data to Sport4U.pro.
6Now you can review your data in Sport4U.pro.
Review your daily walks
N TE: GH-209 built-in pedometer upon own developed algorism counts your daily walks and steps
during your workout.
1Go HISTORY > PEDOMETER to check your steps record and data mana ement.
2STEP LIST
2.1 Under step list, you will see steps data files by date up to 7 records.
2.2 The day 8
th
record will push day 1
st
out of list.
2.3 Push to check each data. Each data listin Total steps, Distance in Km or miles depends on
your settin and Calories in Kcal.
3FEAT
3.1 Records all steps and distance you have taken since you start with this GH-209 till now. This is
more like your walkin achievement.
3.2 You can reset to 0 by reset to factory settin in SETTINGS > ABOUT > RESET > OK!.
4RESET
4.1 The RESET in here only works for the daily works. It can not clear your record in FEAT.
Device Information
GH-209 Specifications
Battery type Rechar eable, built-in lithium-polymer battery
17

Battery life Up to 6 hours in workout mode
Up to 7 days in watch mode
Operatin temperature ran e From 14 to 140°F (-10 to 60°C)
Char in temperature ran e From 32 to 113°F (0 to 45°C)
Radio frequency / protocol Wireless 2.4GHz communication protocol
Water ratin 3 ATM*
*The device withstands pressure equivalent to a depth of 30m. See About 3ATM Water Resistance
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the followin two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
includin interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B di ital device, pursuant
to Part 15 of the FCC Rules. These limits are desi ned to provide reasonable protection a ainst harmful
interference in a residential installation. This equipment enerates, uses and can radiate radio frequency
ener y and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no uarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turnin the equipment off and on, the user is encoura ed to try to correct the
interference by one of the followin measures:
- Reorient or relocate the receivin antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any chan es or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operatin in conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment
and are safe for intended operation as described in this manual. The further RF exposure reduction can be

achieved if the product can be kept as far as possible from the user body or set the device to lower output
power if such function is available.
Device Care
Cleaning the Watch
N TE:
1. Do not use a sharp object to clean the watch.
2. Avoid chemical cleaners, solvents, and insect repellents that can damage plastic components and
finishes.
3. Thoroughly rinse the watch with fresh water after exposure to chlorine, salt water , sunscreen,
cosmetics, alcohol, or other harsh chemicals. Prolonged exposure to these substances can
damage the case.
1Wipe the watch usin a cloth dampened with a mild deter ent solution.
2Wipe it dry.
Cleaning the Heart Rate Monitor
A build up of sweat and salt on the strap can decrease the ability of the heart rate monitor to report
accurate data.
Keep the transmitter strap in a cool and dry place to maximize the heart rate sensor battery lifetime.
Never put the strap in a washing machine or dryer.
1Rinse the strap after every use.
2Hand wash the strap occasionally, usin a tiny amount of mild deter ent, such as dishwashin liquid.
Troubleshooting
Replace Heart Rate Monitor Battery
N TE: If you cannot link to your paired Heart Rate Monitor Belt, maybe the battery required
replacement.
1Four screws are on the back of heart rate monitor module.
2Remove four screws and you can replace the new CR2032 battery.
18