Global FREEFIT Operating instructions

Revised February 2019
INSTALLATION GUIDE
+ OPERATING
INSTRUCTIONS

FREEFIT INSTALLATION GUIDE
2 globalfurnituregroup.com
Page • globalcontract.com2
• August 2014
GLOBALContract
NOTE: Any alterations to listed components will void the manufacturer’s warranty.
The manufacturer will not be responsible for any damage or bodily harm caused
by alterations in accordance with national or local electrical codes and manufac-
turer’s specifications. In accordance with the manufacturer’s policy of continual
product improvement, the product presented in this document is subject to
change without notice or obligation.24
FreeFit
Please contact your Global Contract Service Representative at 416-739-5000 for
any questions or concerns.
Global Contract
Murano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screw
driver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor /
Handle
Socket Wrench
13 mm Socket
Adaptor
Global Contract
Murano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screw
driver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor /
Handle
Socket Wrench
13 mm Socket
Adaptor
Global Contract
Murano Chair Disassembly
Required Tools:
Note: Chair can be disassembled in 5 minutes or less
VERSION 2 03/18/10
Safety Glasses
Rubber Mallet
Flathead Screw
driver
Actuator
Pliers
10 mm Hex Bit
Phillips Bit
T-25 Torx Bit
Bit Adaptor /
Handle
Socket Wrench
13 mm Socket
Adaptor
Safety Glasses Allenkeys Drill with Roberson BitRobertson Screwdriver
Required Tools
TABLE OF CONTENTS
Feet
Crossbars
Sidebar
Bumpers
3-Column 90º Telescopic Crossbars
3-Column 90º Fixed Crossbars
Electric 2 Column
Electric 3 Column
3
3
4
4
5
5
6
Assembly
List ofTools
P.03
P.02
Warning leaflet and user manual should be left on the table after completed installation.
6
FreeFit Height Adjustable Tables page 3
Assembly Hardware 2
Feet 3
Crossbars 3
Sidebars 4
Bumpers 4
3-Column 90° Telescopic Crossbars 5
3-Column 90° Fixed Crossbars 5
Electrical 2-Column 6
Electrical 3-Column 6
Handset Installation 7
FreeFit Height Adjustable Benching page 9
Height Adjustable Back to Back Table - Feet 9
Column Crossbeam 10
Crossbars and Sidebars 11
Bumpers 12
Electrical 2-Column 12
Back-to-Back Trough 13
BWAETTC Table-to-Table Connector 14
Height Adjustable Single Table - Feet 15
Column Crossbeam 15
Crossbars 16
Sidebars 16
FreeFit Height Adjustable Benching (cont’d)
Bumpers 17
Electrical 2-Column 17
Single table trough 18
BWAECF Ceiling Feed Post 19
BWAEEF Floor Feed Housing 20
Device Holder Acess Door Modules 21
Worksurfaces 22
Cable Snake 23
Cable trough covers 24
BWAPCH PC Holder 25
Cable Tray Access Door Modules w/Cable Tray 26
Power Bar - All Access Door Modules 27
BWATMGD Table Mounted Glass Divider 28
Stationary Divider Assembly 29
Stationary Divider Install 30
Table Mounted Framed Dividers 33
Back-to-Back FreeFit to Bridges Connector 34
Handset Installation 37

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 3
Page • globalcontract.com4
• August 2014
GLOBALContract
Feet
Crossbars
INSTALLATION GUIDELINES
Screw Socket Round UNC 5/16- 18x5/8” Zn
Loosen screws to adjust crossbar length.
Screw socket CSK UNC
5/16 - 18x1” Zn
Do not use the two middle holes of the crossbars.
Adjustable crossbar
Fixed crossbar
Assemble the feet on the columns. Tighten screws firmly.
IMPORTANT: Make sure the correct screws are used. Using too
long screws may destroy internal parts in the column.

FREEFIT INSTALLATION GUIDE
4 globalfurnituregroup.com
•Pageglobalcontract.com 5
• August 2014
GLOBALContract
INSTALLATION GUIDELINES
Sidebars
Bumpers
Screw socket CSK UNC
1/4-20x5/8” Zn
Bumper ø 1/2”x 1/8”
Transparent
Bumper 1/2”x 1/2”x1/4”
Transparent
Right Hand / Left Hand
Sidebars
Fasten sidebars in threaded holes on top of crossbars with countersunk screws.
Various types of sidebars exist, some of which can be placed in optional positions.
The holes closest to the ends of the sidebar are dedicated for fixing of work top but
any available hole can be used for this purpose.
The work top is resting on the sidebars and on self-adhesive
rubber bumpers placed on the crossbars. The bumpers should
be placed as close to the fixing screws for the work top as pos-
sible to keep the work top from bending.
The rubber bumpers come in two thicknesses. The thicker ones
are used on the C-channel. On fixed crossbars the thick bumpers
are not used.
Two sizes of wood screws for the work top are included
in the assembly kit. Wood Screw Round 8x3/4” Zn Wood
screw CSK 10x2-3/8” Zn
The shorter screws through sidebars. The longer screws
through crossbars.
Place the thin bumpers on the
tube next to the screw hole
and next to the tube edge.
Place the thick bumpers on
the C-channel next to the
screw hole.

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 5
Page • globalcontract.com6
• August 2014
GLOBALContract
Screw socket CSK
UNC 5/16-18x1-
3/8” Zn
Screw socket CSK
UNC 5/16-18x1-
3/8” Zn
3 Regular fixed crossbar.
Regular fixed crossbar 6” shorter
than the other three crossbars.
Assembly Kit PR25 90º Angle
3 Regular telescopic crossbars.
1 Special Telescopic crossbar.
No additional assembly kit.
3-Column 90°Telescopic Crossbars
3-Column 90° Fixed Crossbars
Attach the crossbars on the long side of the housings. Tighten
screws firmly. IMPORTANT: Do not use the two middle holes of the
crossbars. Do not insert any object in the two middle holes as this
can damage electronic components.
Loosen the round headed screws on the cross-bars and adjust the
frame to desired width.
Fasten the screws on the crossbars.
3 regular telescopic crossbars and 1 special telescopic crossbar
with an angled C-channel are used.
3-Column 90º Table, Fixed Crossbars 3 regular fixed crossbars
together with 1 regular fixed crossbar 6” shorter than the other
three are used.
The assembly procedure is the same as for a 2-column table with
the exception that the angled C-channel mounts to the middle house
with one extra-long screw 1-3/8”.

FREEFIT INSTALLATION GUIDE
6 globalfurnituregroup.com
Electrical 2-Column
The handset is mounted at the front edge of the work top, screwed to the underside with screws supplied with the unit.
Connect cables and power supply according to:
Cable USA 2-pol IEC C7
HandsetCable LinBus iDrive
Power Supply D04 35V/2, 12A AC input 110-240V, 50-60Hz
Electrical 3-Column
Cable USA 2-pol IEC C7
Handset
Cable LinBus iDrive
Power Supply
Standard Handset Digital Handset Power Supply Holder

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 7
Handset Installation
Using Controls
Button Guide
- Adjust the table upwards
- Scroll up when in the Menu
- Adjust the table downwards
- Scroll down when in the Menu
- Menu, to enter Menu mode
- Enter, when in Menu mode
15 sec – sleep mode
Display backlight will go to sleep mode after
15 seconds of inactivity.
Symbol Guide
Explanation of the display
Understanding the symbols
Menu mode
Memory
Error codes
Reset
Homing mode 73 8
Imperial, inch
Thermometer
Metric, centimeter
Height reading
73 8
Start-up indications
Three dashes
or with a slave number such as
Height reading
25.2”
1
Start up
Once connected, a height read-out should appear on the
display.
---
Perform Reset/Homing
Critical step. At installation or if a critical component such as a
column or motor is changed or disconnected, a Reset must be
performed.
NOTE! Ensure that the area around and under the table are clear.
and Press and hold the Up and Down buttons at
the same time
8 seconds
Hold the buttons pressed at least 8 seconds
Release
Release the Up and Down buttons
---
Immediately press and hold the Down button -
the display will indicate reset mode with three
dashes and a house in the lower left corner
- until the desk reaches its lowest position
and stops moving
Release
Release the Down button
Height reading
The three dashes on the display will be
replaced by a height reading
Complete
The reset process is completed
Use preset heights
or Adjust the table to the preferred height to be
stored as a memory position
Press the M button, and release
or Immediately press the Up or Down button to
store the current height as a quick memory
position to the selected button
or Press and hold either the Up or Down button
to move the desk to the quick memory posi-
tion, the desk will stop at the preset height.
Release the button.
or Press and hold the same button as previously
to bypass the desks preset height.
Memory Positions
Set/Adjust a quick memory position. There is a quick
memory position option to set the Up and Down buttons to
move the desk to a predefined height. To set the predefined
height for a button:
or Move the table to desired height
Hold the M button for at least 3 seconds
Use the Down button to navigate to SET
Press the M button to select
1, 2 OR 3 Use the Up or Down button to select position
to store the height to, 1, 2 or 3.
Press the M button to save
current height
Setting Memory Positions 1 – 3
Accessing Memory Positions 1 – 3
Hold the M button for at least
3 seconds
1, 2 OR 3 Use the Up or Down button to choose stored
position 1, 2 or 3
Press and hold the M button while the table
moves to the stored memory position
Use the 2 included screws for fixing to the tabletop. If the thickness
of the tabletop is less than 1”, please use shorter screws.
In situations of sloped tabletop edges, there could be the need for
a third fixing point. When choosing a screw, consider the handset
will take up a 1/2” of the screw length.
Attach the hand switch cable to the closest column. The second
port on the handset can be used to connect other devices.

FREEFIT INSTALLATION GUIDE
8 globalfurnituregroup.com
•Pageglobalcontract.com 9
• August 2014
GLOBALContract
Wheel Controls
How to set memory:
Run/Drive the table to the position you will store,
sitting or standing.
(This device have 5 memories position memories)
Press menu button + “stand” icon 1 time to come
to set memory menu.
Calibrate:
Measure the distance between the floor and the top
of the table sheet.
Press menu button + “stand” icon 2 times to come
to calibrate menu.
Use arrow up and down to navigate to set memory
setting.
Press Menu/Enter, and the value are stored.
The display confirm by flashing 3 times and then
returns to normal mode.
Press Menu/Enter to confirm
Press Menu/Enter to confirm
Press Menu/Enter, and the value are stored.
Press Menu/Enter, and the value are
stored.
Adjust the figures to the selected value with the
arrows up or down.
1
5
CAL
28
.
0
Upper limit:
Set the upper limit if there are limited
space in height.
Press menu button + “stand” icon 3
times to come to set memory menu.
Units:
Choose between metric or imperial
system.
Press menu button + “stand” icon 5
times to come to set memory menu.
Error codes:
Reset Away:
Press menu button + “stand” icon 6
times to come to set memory menu.
Lower limit:
Set the lower limit if there are device/
equipment which could create a risk
of pinching or risk for table damages.
Press menu button + “stand” icon 4
times to come to set memory menu.
Adjust the figures to the chosen level
with the arrows up or down.
Press Menu/Enter to confirm. Press Menu/Enter to confirm.
1. Hard stop
2. Back off
3. Soft top
4. Waiting for button
5. Waiting for button release.
6. Motor lost
Overheating. Thermometer flashing,
wait 10 minutes for motor cooling.
Adjust the figures to the chosen level
with the arrows up or down.
Adjust the figures to the chosen level
with the arrows up or down.
Press Menu/Enter, and the value are
stored.
Press Menu/Enter, and the value are
stored.
Press Menu/Enter, and the value are
stored.
Press ‘down” and hold until the columns
have gone to the lowest position.
Do reset if any parts have been changed
of if you discover interference between
the columns.
Please note that the figures count
from the table top surface.
Please note that the figures count from
the table top surface/ calibrated level.
UL
50
.
0
LL
27
.
5
UN
RES
3
Using Controls
Calibrate
If the height reading displays incorrect height, the
height from the table top needs to be
calibrated.
Measure the distance between the floor and the top
of the table top.
Press and hold M button for at least 8
seconds...
--- ...until three dashes are displayed
Release
Release the M button
CAL Use the Up or Down button to
navigate to CAL (Calibrate)
Select by pressing the M button
or Change the current height reading by using
the Up or Down button to the measured height
Store the current height reading and return to
Menu by pressing the M button
Upper Limit
Set an Upper Limit when planning over-head storage
Press and hold M button for at least 8
seconds...
--- ...until three dashes are displayed
Release Release the M button
U . L . Use the Up or Down button to
navigate to U.L. (Upper Limit)
Select by pressing the M button
or Calibrate Upper Limit by using the Up or
Down buttons
Select value and return to Menu by pressing
the M button
Lower Limit
Set a Lower Limit when planning storage under the table
Press and hold M button for at least 8
seconds...
--- ...until three dashes are displayed
Release Release the M button
L . L . Use the Up or Down button to navigate to L.L
(Lower Limit)
Select by pressing the M button
or Calibrate Lower Limit by using the Up or
Down button
Select value and return to Menu by pressing
the M button
Units
Change between metric or imperial units
Press and hold M button for at least 8
seconds...
--- ...until three dashes are displayed
Release Release the M button
Use the Up or Down button to navigate to
Un (Units).
Select by pressing the M button
CM OR “
Choose CM (centimeter) or “ (inch) with the Up
or Down button
Select value and return to Menu by pressing
the M button
Performing a Forced Reset
If Standard Reset (page 6) does not initiate
a reset, perform a Forced Reset
Press and hold M button for at least 8
seconds...
--- ...until three dashes are displayed
Release
Release the M button
RES Use the Up or Down button to navigate to
RES. (Reset)
Select by pressing the M button
Activate Reset/Homing by
pressing the Down button
Software Version
Display Software Version
Press and hold M button for at least 8
seconds...
--- ...until three dashes are displayed
Release Release the M button
SOF Use the Up or Down button to navigate to SOF
(Software Version)
Select by pressing the M button
Software Version
displayed
Software Version will appear on the display
Return to Menu by pressing the M button

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 9
Height Adjustable Back-To-Back Table - Feet
FFHABDKS, FFHABDKE
Assemble the feet on the columns. Tighten the screws firmly.
Important: Make sure the correct screws are used. Using too long screws may destroy the internal parts in the column.
Screw socket round UNC5/16 - 18x5/8” Zn

FREEFIT INSTALLATION GUIDE
10 globalfurnituregroup.com
Column Crossbeam
Secure the column crossbeam to the columns.
STEP 1: Drive one socket head screw 5/16-18 x 1” into column as illustrated.
Do not tighten.
STEP 2: Position the column crossbeam’s key-hole over the pre-installed
socket head screw and drive in the second socket head screw.
Note: When the column crossbeam orientation is completed, one pair of the
holes will end up at the beam’s bottom (A) and the second pair of holes (B)
will point toward the center of the table.
STEP 3: Tighten all socket head screws to ensure firm and safe column-to-column
crossbar connection.
1
2
3
A
B

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 11
Crossbars and Sidebars
Fasten sidebars in threaded holes on top of crossbars with countersunk screws.
There are various types of sidebars , some of which can be placed in optional
positions. The holes closest to the ends of the sidebar are dedicated for fixing th
e
worksur
face but any other available hole can be used for the same purpose.
Screw socket CSK UNC
1/4 - 20x5/8” Zn
Screw socket CSK UNC
5/16 - 18x1” Zn
Loosen screws to adjust crossbar length
Do not use the two middle
holes of the crossbars.
Do not use the two middle holes of the crossbars.
Adjustable Crossbar
Fixed Crossbar
Right hand Sidebar
Left hand
Sidebar

FREEFIT INSTALLATION GUIDE
12 globalfurnituregroup.com
Bumpers
The worksurface is resting on the sidebars and on self-adhesive rubber bumpers placed on the crossbars. These bumpers should be placed close to the fixing screws to avoid the
worksurface bending.
The rubber bumpers come in two thicknesses. The thicker bumpers are used on the C-channel and not on the fixed crossbars.
Place the thick bumpers on the C-channel next to the screw hole.
Place the thin bumpers on the tube next to the screw hole and next to the tube edge.
Electrical 2-Column
The handset is mounted at the front edge of the worksurface, screwed to the underside with the screws supplied.
Connect cables and power supply according to:
Power Supply D04 35V/2, 12A AC input 110-240V, 50-60HzCable USA 2-pol IEC C7
Cable LinBus iDrive
Handset

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 13
Back-to-Back Trough
Secure the column crossbeam to the columns.
STEP 1: Drive two head screws 5/16-18 x 1” into the column crossbeam as illustrated. Do not tighten.
STEP 2: Drop in the trough and guide slots over the pre-installed socket head screws. Note: Check if the installation calls for central, shared divider. If so, install the divider’s bottom
brackets now, before tightening the socket screws. If not, proceed to step 3.
STEP 3: Tighten all socket head screws.
STEP 4: Install the power distribution components and data cables before snapping into the bottom trough channel.
1
3
2
4

FREEFIT INSTALLATION GUIDE
14 globalfurnituregroup.com
BWAETTCxx Table-to-Table Connector
Continue with assembling all the remaining table structures, including power troughs and place them in their desired location. Proceed from the first table assembly at the beginning
of a run and install the table-to-table connector to organize cables and establish an accurate distance.
STEP 1: Position the table-to-table connector under the column crossbeam and align its holes with threaded holes in the bottom of the column crossbeam. Secure with two supplied
machine screws.
STEP 2: Finalize adjacent table assembly, align the adjacent column crossbeam holes with the holes on the opposite side of the table-to-table connector.
STEP 3: Secure the table-to-table connector with two supplied machine screws.
STEP 4: Install the power distribution components and data cables before snapping them into the bottom trough channel.
1/4-20x0.5” pan head
machine screw x4
1
2
3
4

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 15
Height Adjustable Single Table - Feet
FFHABSKS, FFHABSKE
Assemble the feet on the columns. Tighten screws firmly.
IMPORTANT: Make sure the correct screws are used.
Using too long screws may destroy the internal parts in the column.
Screw socket round UNC 5/16 - 18x5/8” Zn
Column Crossbeam
Secure the column crossbeam to the columns.
STEP 1: Drive one socket head screw 5/16-18 x 1” into column as illustrated. Do not tighten.
STEP 2: Position the column crossbeam’s key-hole over the pre-installed socket head screw and drive in the second socket head screw. Once the column crossbeam orientation is
completed, one pair of holes will end up at the beam’s bottom (A) and the second pair (B) will point toward the center of the table.
STEP 3: Tighten all socket head screws to ensure a firm and safe column-to-column crossbar connection.
1
2
3B
A

FREEFIT INSTALLATION GUIDE
16 globalfurnituregroup.com
Crossbars
Do not use the two middle holes of the crossbars.
Adjustable Crossbar
Fixed Crossbar
Screw socket CSK UNC
5/16 - 18x1” Zn
Loosen screws to
adjust crossbar length
Sidebars
Fasten sidebars in threaded holes on top of crossbars with countersunk screws.
There are various types of sidebars, some of which can be placed in optional positions.
The holes closest to the ends of the sidebar are dedicated for fixing the worksurface but
any other available hole can be used for the same purpose
Screw socket CSK UNC
1/4 - 20x5/8” Zn Right hand
sidebars
Left hand
sidebars

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 17
Bumpers
The worksurface is resting on the sidebars and on self-adhesive rubber bumpers placed on the crossbars. These bumpers should be placed close to the fixing screws to avoid the
worksurface from bending.
The rubber bumpers come in two thicknesses. The thicker bumpers are used on the C-channel and not on the fixed crossbars.
Place the thick bumpers on the C-channel next to the screw hole.
Place the thin bumpers on the tube next to the screw hole and next to the tube edge.
Bumper 1/2” x 1/8”
Transparent
Bumper 1/2” x 1/2” x 1/4”
Transparent
Two sizes of wood screws for the work top are included in the assembly kit.
- Wood screw round 8 x 3/4” Zn
- Wood screw CSK 10 x 2-3/8” Zn
The shorter screws go through sidebars; the longer screws go through crossbars.
Electrical 2-Column
The handset is mounted at the front edge of the worksurface, screwed to the underside with the screws supplied.
Connect cables and power supply according to:
Power Supply D04 35V/2, 12A AC input 110-240V, 50-60HzCable USA 2-pol IEC C7
Cable LinBus iDrive
Handset

FREEFIT INSTALLATION GUIDE
18 globalfurnituregroup.com
Single Table Trough
STEP 1: Drive two socket head screws 5/16-18 x 1” into the single table column crossbeam as illustrated. Do not tighten.
STEP 2: Drop in the single-sided trough and guide slots over the pre-installed socket head screws.
STEP 3: Tighten all socket head screws.
STEP 4: Install the power distribution components and data cables before snapping in the bottom trough channel.
1
2
3
4

FREEFIT INSTALLATION GUIDE FREEFIT INSTALLATION GUIDE
globalfurnituregroup.com 19
BWAECF Ceiling Feed Post
Proceed with the installation of the ceiling feed power pole only after all the table assemblies
and interconnecting trough bridges have been installed and their position finalized.
STEP 1: Remove bottom trough channel.
STEP 2: Align screw ports on ceiling feed pole extrusion with holes in the trough bridge.
STEP 3: Secure the pole to the trough bridge with the supplied screws.
STEP 4: Install the power distribution components and data cables before snapping them into
the bottom trough channel.
1
2
3
4
1
2
3
4

FREEFIT INSTALLATION GUIDE
20 globalfurnituregroup.com
BWAEEF Floor Feed Housing
STEP 1: Rotate the base feed mounting bracket into the bottom slot in the
column crossbeam.
STEP 2: Push the bracket against the leg column, align the bracket round
hole with threaded hole in the bottom of the column crossbeam. (The bracket
shares screws with the trough bridge which needs to be installed first,
followed by the base feed mounting bracket.) Screw ports on ceiling feed
pole extrusion with holes in trough bridge.
STEP 3: Secure the base feed mounting bracket with the supplied 1/4-20 screw.
STEP 4: Position the base feed cover in place.
A) Connect base feed’s connector to adjacent power distribution module.
B) Tuck in the data cable bundle so that it enters the cover through the front
bottom hole and exits through the top front hole and into the power trough.
STEP 5: Close the cover, align the holes.
STEP 6: Secure the cover with four supplied machine screws.
STEP 7: Complete the installation of the power distribution components and
data cables before snapping them into the bottom trough channel.
STEP 8: Normally symmetrical bottom trough channel associated with the
trough bridge needs to be trimmed on the adjacent side of the base feed:
A: To avoid the bottom trough channel extrusion interfering with the power
and data conduits from the existing base feed, please cut it off at one notch
down as illustrated.
B: Completed installation.
8
6
4
B
A
3
2
1