Glyn XBee910 Quick user guide

HARDWARE REFERENCE MANUAL
XBee910
A Telit cellular module on an Xbee interface board
February 1, 2019
Revision 1.1

Revision Date Notes
1.0 22/06/2018 Initial hardware reference manual
1.1 19/09/2018 Updated images and dimensions added
Glyn Ltd. XBee Hardware Reference Manual Pg.1

Contents
1 Introduction 3
2 Mechanical Specifications 4
2.1 Dimensions ............................ 4
2.2 SocketTypes ........................... 4
2.2.1 10-Pin Right Angle Surface Mount Header . . . . . . . 4
2.2.2 U.FL Connector . . . . . . . . . . . . . . . . . . . . . . 4
3 Hardware Specifications 5
3.1 Pinout............................... 5
3.2 Antenna Connectors . . . . . . . . . . . . . . . . . . . . . . . 5
3.3 Hardware Commands . . . . . . . . . . . . . . . . . . . . . . . 6
3.4 PowerSupply ........................... 6
3.5 PowerConsumption ....................... 6
3.6 BlockDiagram .......................... 6
3.7 Recommended Module Summary . . . . . . . . . . . . . . . . 7
Glyn Ltd. XBee Hardware Reference Manual Pg.2

1 Introduction
The XBee910 module has been designed to allow the user ease of use with
plug & play cellular modules with the Digi R
XBeeTM interface. Options are
available for Cat-M1, Cat-1, LTE, GSM, UMTS and HSPA.
By utilising the XBeeTM interface the XBee910 allows the user the option
to mount the module that best suits each particular application use case, no
matter where in the world it is going to be deployed.
In most cases your design needs to provide flexibility depending which
region the product is to be deployed. The XBeeTM form factor with xE910
module allows you to take the guesswork out of the design by providing a
single connector solution for interfacing the entire range of radio types avail-
able depending on your needs.
Full electrical and software (AT commands) compatibility is maintained
between each module type, be it Cat-M1 (ME910C1-AU), Cat-1 (LE910C1-
AP, or HSPA+ (HE910-DG).
The Glyn XBee range also includes support for Sigfox and LoRa modules.
Glyn Ltd. XBee Hardware Reference Manual Pg.3

2 Mechanical Specifications
2.1 Dimensions
34mm x 29.5mm x 11mm(including header)
2.2 Socket Types
2.2.1 10-Pin Right Angle Surface Mount Header
Manufacturer: Samtec Inc.
Part Number: TMM-110-01-T-S-SM
Pitch - Mating: 0.079”(2.00mm)
No. of Positions: 10
No. of Rows: 1
Mounting Type: Surface Mount
2.2.2 U.FL Connector
Manufacturer: Attend
Part Number: 321-33125
Glyn Ltd. XBee Hardware Reference Manual Pg.4

3 Hardware Specifications
3.1 Pinout
Pin Function Description
1 VCC Supply, supported range 3.3-4.2V
2 DOUT UART transmit
3 DIN UART receive
4 GND Ground
5 RESET nIN Reset Low
6 VUSB USB supply, supported range 4.4-5V*
7 USB+ Data +
8 USB- Data -
9 DTR UART data terminal ready
10 GND Ground
11 GND Ground
12 CTS UART clear to send
13 ON/nSLEEP 1.8V output, drives on-board LED via MOSFET
and connected to GPIO1/STAT LED
14 VREF Vref(Must be connected and >=1.8V)
15 GND Ground
16 RTS UART request to send
17 DIO3 1.8V GPIO3
18 DIO2 1.8V GPIO2
19 ADC1 1.8V ADC1
20 ON/OFF 1.8V must be driven to open drain/collector
3.2 Antenna Connectors
The XBee910 module is equipped with a 50 Ohm RF connector from At-
tend, P/N: 321A-33125, for Cellular, Diversity (where applicable), and GNSS
(where applicable) antenna connections. These connectors are located on top
side (Cellular and Diversity) and bottom side (GNSS).
Interface cables with various configurations are available from Glyn, to
suit your needs: Glynstore Interface Cable Range
Glyn Ltd. XBee Hardware Reference Manual Pg.5

3.3 Hardware Commands
Please see the relevant Telit xE910 Hardware user guide for more details.
The document can be found at Telit website.
3.4 Power Supply
XbeeTM interface supports 3.3-4.2V.
Please see the relevant Telit xE910 Hardware user guide for recommended
power supply requirements for new designs. The document can be found at
Telit website.
3.5 Power Consumption
Please see the relevant Telit xE910 Hardware user guide for recommended
power supply requirements for new designs. The document can be found at
Telit website.
3.6 Block Diagram
Block Diagram of LE910C1-AP
Glyn Ltd. XBee Hardware Reference Manual Pg.6

3.7 Recommended Module Summary
Part
Number
Region Technologies Band Support GPS
GE910-
QUAD
Global(2G
Only)
2.5G 850, 900, 1800,
1900 MHz
No
HE910-D Global 3G 800/850, 900,
AWS1700, 1900,
2100
No
HE910-
DG
Global 3G 800/850, 900,
AWS1700, 1900,
2100
Embedded
HE910-
EUD
EMEA/
APAC/
Latin Amer-
ica
3G 800/850, 900,
2100
No
HE910-
EUG
EMEA/
APAC/
Latin Amer-
ica
3G 800/850, 900,
2100
Embedded
LE910C1-
AP
APAC/ANZ 4G(3G Fall-
back)
B1, B3, B5, B8,
B28 (850, 900,
2100)
Embedded
ME910C1-
AU
Austraila Dual Cat1 &
NB1 4G
B3, B5, B8, B28 Optional
Embed-
ded
ME910C1-
WW
Worldwide Dual Cat
M1 & NB1
4G(2G fall-
back)
B1, B2, B3, B4,
B5, B8, B12,
B13, B18, B19,
B20, B26, B28,
B39(850, 900,
1800, 1900)
Optional
Embed-
ded
Glyn Ltd. XBee Hardware Reference Manual Pg.7