gofanco HDbitTPro User manual

HDMI HDbitT CAT5e/6
Extender 1080p with
Loopout - 120m
User's Guide
G4-0054A
1
P/N: HDbitTPro

2
Thank you for purchasing from gofanco. Our
products aim to meet all your connectivity needs
wherever you go. For optimum performance
and safety, please read the instructions carefully
and keep this User’s Guide for future reference. If
you need more information about our products,
please visit www.gofanco.com. For technical
support, pleaseemail usat [email protected].
For drivers/manuals download, please go to
http://www.gofanco.com/download.
Important Safety Notices
Please read safety instructions carefully before
installation and operation.
• Please pay close attention to all warnings
and hints for this device
• Do not expose this unit to rain, heavy
moisture, or liquid
• Do not repair the device or open the
enclosure without professional guidance to
avoid electric shocks. Doing so may void
your warranty
• Keep the product in a well-ventilated
location to avoid damage from overheating

3
• Shut off power and make sure environment
is safe before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid
cable damage. Make sure they are plugged
into the correct ports
• Use the included DC5V power adapters
only. Make sure the specification matches if
using 3rd-party DC power adapters
Introduction
The HDMI HDbitT CAT5e/6 Extender 1080p
with Loopout - 120m extends high definition
1080p HDMI signals from a source device to a
display device up to 120 meters through a single
economical CAT5e/6 cable using advanced
HDbitT transport protocol.

4
Features
• Transmits HDMI signals from source device
to display device up to 120 meters using
economical CAT5e/6 cabling
• Supports IR remote control function to
controlthe sourcedevice fromlong distances
• Supports additional Receivers (part #
HDbitTPro-RX) sold separately
• HDMI out on the Transmitter (TX) for local
monitoring of the HDMI signal
• Easy and clean installation
Package Contents
Transmitter (TX) (1pc) Receiver (RX) (1pc) User's Manual (1pc)
Power Adapter
5VDC/1A (2pcs)
IR Blaster Extension
Cable (1pc)
IR Receiver Extension
Cable (1pc)

5
Product Layout
Figure 1: Transmitter (TX)
1Power LED: On when the Transmitter is
powered
2Activity LED: Blinks during data
transmission
3Link LED: On when the Cat5e/6 cable is
connected/linked properly to Transmitter's
and Receiver's RJ45
4Reset: Press to reset if HDMI extender
doesn't work properly
5Power Jack: Connect the included power
adapter here
6RJ45 Out: Link to Receiver's RJ45 In using a
Cat5e/6 cable
7IR Out: Infrared 3.5mm socket. Plug IR
Blaster Extension Cable here. See
instructions on page 8.
8HDMI Out: Connect an HDMI display here
for local monitoring of the HDMI signal

6
9HDMI In: Connect your HDMI source here
with an HDMI cable (cable not included)
Figure 2: Receiver (RX)
1Power LED: On when the Receiver is
powered
2Activity LED: Blinks during data
transmission
3Link LED: On when the Cat5e/6 cable is
connected/linked properly to Transmitter's
and Receiver's RJ45
4Reset: Press to reset if HDMI extender
doesn't work properly
5Power Jack: Connect the included power
adapter here
6RJ45 In: Link to Transmitter's RJ45 Out
using a Cat5e/6 cable
7IR In: Infrared 3.5mm socket. Plug IR
Receiver Extension Cable here. See
instructions on page 8.

7
8HDMI Out: Connect an HDMI display here
with an HDMI cable (cable not included)
Installation Requirements
1. HDMI source device (computer, DVD
player, etc)
2. HDMI display device (SDTV/Monitor,
HDTV/Monitor, projector, etc.)
3. UTP/STP CAT5e/6 cable following
IEEE-568B wiring standard
Hardware Installation
1. Power off all devices including your HDMI
source and HDMI display(s).
2. Connect your HDMI source device to the
Transmitter's HDMI Input connector with
an HDMI cable (HDMI cable not included).
3. Optional: Connect an HDMI display to the
Transmitter's HDMI out connector with an
HDMI cable (cable not included). This
connection is needed only if you need local
monitoring of the HDMI signal.

8
4. Optional: Connect the IR Blaster Extension
Cable to the Transmitter's IR Out port. Face
the eye towards your HDMI source device's
IR window. This connection is needed only
if you need to control your HDMI source
from the remote location.
5. Plug your Cat5e/6 cable between the
Transmitter's RJ45 Out and Receiver's RJ45
In.
6. Connect your HDMI display to the
Receiver's HDMI output connector with an
HDMI cable (HDMI cable not included).
7. Optional: Connect the IR Receiver Extension
Cable to the Receiver's IR In port. This
connection is needed only if you need to
control your HDMI source device from the
remote location.
8. Plug the included power adapters into the
Transmitter's and Receiver's power jacks,
then plug them into a reliable power source.
9. Power on all connected devices.
10. The HDMI extender is ready for use.

9
Application
1. One-to-One: Extends HDMI signals up to
120 meters over a single Cat5e/6 cable.
2. One-to-Many: Extend and split using
dedicated network router/switch.
- One Transmitter (TX) to several Receivers
(RX)
- Additional Receivers (part # HDbitTPro-
RX) sold separately
Transmitter
Receiver
Receiver
Receiver
Transmitter
Receiver

10
3. Cascade: Unlimited extension with
dedicated network router/switch.
Transmitter
Receiver