gofanco HDwireless100 User manual

Wireless HDMI Extender
Kit 1080p - 100m
User's Guide
G4-0077A
P/N:HDwireless100

2
Thank you for purchasing from gofanco. Our products
aim to meet all your connectivity needs wherever you
go. For optimum performance and safety, please read
the instructions carefully and keep this User's Guide for
future reference. If you need more information about
our products, please visit www.gofanco.com. For
technical support, email us at [email protected].
For drivers or manual download, please go to
www.gofanco.com/download.
Important Safety Notices
Pleasereadsafetyinstructionscarefullybeforeinstallation
and operation.
• Please pay close attention to all warnings and hints
for this device
• Do not expose this unit to rain, heavy moisture, or
liquid
• Do not put any items into the device or attempt to
modify its operation
• Do not repair the device or open the enclosure
without professional guidance to avoid electric
shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to
avoid damage from overheating
• Shut off power and make sure environment is safe
before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid cable
damage. Make sure they are plugged into the
correct ports
• Use the included DC5V power adapters only. Make
sure the specification matches if using 3rd-party
DC power adapters

3
Introduction
The Wireless HDMI Extender Kit 1080p - 100m extends
HDMIsignals wirelessly froma source deviceto a display
device up to 100 meters. It requires no cables between the
Transmitter (TX) and Receiver (RX), making the
installation easy and clean. Great for homes and offices.
Note: Wireless transmission distance will vary due
to the environmental conditions. Thick walls, brick,
glass, electronic interference, and wireless signals
from other devices will shorten the wireless
transmission distance or cause signal loss.
Features
• Transmits HDMI signals in 1080p up to 328ft (100
meters) wirelessly
• HDMI loop-out on the transmitter to connect a local
display, allows easy monitoring of the source signal
• IR extension allows you to control the source device
from a remote location
• No cables required between Transmitter (TX) and
Receiver (RX)
• Less than 0.5 seconds latency, not recommended for
real-time applications such as PC gaming
• Dual antenna maximizes wireless reception with
stable data transmission

4
PackageContents
IR Blaster Cable (1pc)
Receiver (RX) (1pc) DC5V/2A Power
Adapter (2pcs)
Transmitter (TX) (1pc)
IR Receiver Cable (1pc) User's Guide (1pc)
Installation Requirements
1. HDMI source device (DVD player, set top box, PC,
etc.)
2. HDMI display device (SDTV/Monitor, HDTV/
Monitor, projector, etc.)
3. HDMI cables (not included)
Antenna (4pcs)

5
Product Layout
Figure 1: Transmitter (TX)
Figure 2: Receiver (RX)
1. Antenna Connects to an included antenna
2. Power Jack Connects to an include Power Adapter
3. HDMI Input Connects to an HDMI source device
4. HDMI Signal LED On when the HDMI source signal is detected
5. Wireless Connection LED On: The Transmitter and Receiver are linked
Off: The Transmitter and Receiver are not linked
6. HDMI Output Connects to an HDMI display
7. IR Output Connects to the IR Blaster Cable
8. Antenna Connects to an included antenna
9. Reset Button Press the button to reset the Transmitter
1. Antenna Connects to an included antenna
2. Power Jack Connects to an included power adapter
3. Wireless Connection LED On: The Receiver and Transmitter are linked
Off: The Receiver and Transmitter are not linked
4. Data Transmission LED Blinks slowly: Detecting wireless signal
Blinks fast: Successfully linked or transmitting data
5. HDMI Output Connects to an HDMI display
6. IR Input Connects to the IR Receiver Cable
7. Antenna Connects to an included antenna
8. Reset Button Press the button to reset the Receiver

6
Hardware Installation
1. Power off all devices including your HDMI source
and HDMI display(s).
2. Install the included antennas to the TX and RX.
3. Connect your HDMI source device to the
Transmitter'sHDMIInputconnectorwithanHDMI
cable (HDMI cable not included).
4. Optional: Connect your HDMI display to the
Transmitter's HDMI Output connector with an
HDMI cable (HDMI cable not included). This
connection allows you to monitor the HDMI signal
from the source device location.
5. Optional: Connect the IR Blaster Cable to the
Transmitter's IR interface port. Face the eye
towards your HDMI source device's IR window.
This connection is needed only if you need to
control your HDMI source from the remote
location.
6. Connect your HDMI display to the Receiver's
HDMI Output connector with an HDMI cable
(HDMI cable not included).
7. Optional: Connect the IR Receiver Cable to the
Receiver's IR interface port. This connection is
needed only if you need to control your HDMI
source from the remote location.
8. Plug the included power adapters into the
Transmitter's and Receiver's Power Jacks, then
plug both power adapters into reliable power
outlets.

7
ApplicationDiagram
Figure 3: Application Diagram
9. Power on your HDMI source device and HDMI
display(s). The wireless extender is ready for use.
Note: For optimal signal range, install in a clear
environment with few obstacles. Wireless signals
from other devices, such as microwaves, wireless
mice and keyboards, etc. may interfere with
transmission. Contact our technical support team
if you have specific questions.
Local Display
HDMI source
Transmitter Receiver
IR Blaster
IR Receiver
Display
Power Adapter
Power Adapter

8
Notice
• Wireless signals transmitted through walls, glass,
brick or other solid objects will cause signal loss
and decrease the transmission distance
• Externalwireless signals frommicrowaves, wireless
mice and wireless keyboards will interfere with
HDMI signal transmission
• Keep the unit in a well ventilated environment to
prevent it from overheating
•DO NOT exposetheunit to rain,moisture, or liquids
•DO NOT place anything on the unit
•DO NOT open the housing, doing so will void the
warranty and may cause personal injury due to
electronic hazard
•DO NOT plug-in or remove the IR extension cables
when the unit is powered on

9
FAQ & Troubleshooting
Q: The Wireless Connection LED is on, but no video
output on the remote display:
A: 1) Check the HDMI source device is powered on.
2) Check the transmitter's HDMI Signal LED is on.
3) Check the HDMI cables for solid connection. Use
different HDMI cables if necessary.
4) Press the Reset button on both TX and RX.
5) Connect the HDMI source device directly to the
display to see if there is a signal.
Q: Poor video quality:
A: 1) Check the HDMI cables are connected properly.
Use different HDMI cables if necessary.
2)Changetheangleof the antenna on the transmitter
unit and receiver unit. Generally, the antenna angle
should be positioned as far apart as possible.
3)Adjustthepositionoftransmitter unit and receiver
unit, and make sure they are within the required
signal range.
4) Press the "Reset" button on the transmitter unit
and receiver unit and reconnect.
5) Remove other wireless signals and move any
obstacles that are blocking the signal line-of-sight.
6) Decrease the distance between the transmitter
unit and the receiver unit.

10
Specifications
Item Specification
Wireless Frequency 5GHz
Wireless Latency <500ms
Resolution (Input & Output)
480i@60Hz, 480P@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@50/60Hz
Compliance HDMI 1.3
HDCP 1.2
IR Remote Control Supports 20KHz~60KHz IR remote devices
Transmission Distance Up to 100 meters
Operating Temperature 32° - 122° F (0° - 50° C)
Power Adapter Output: DC5V/2A
Power Consumption TX: <7W / RX: <5W
Housing Material Metal
Product Dimensions (TX & RX) 5.20" (L) x 4.78" (H) x 0.85" (W)
Weight TX: 0.68 lbs / RX: 0.68 lbs
Color Black

11
Disclaimer
The product name and brand name may be registered
trademarks of related manufacturers. TM and ® may be
omitted on the user's guide. The pictures on the user's
guide are just for reference, and there may be some slight
differences with the actual products.
We reserve the right to make changes without prior
noticeto a productor system describedherein to improve
reliability, function, or design.

Thank you for choosing gofanco
www.gofanco.com