gofanco HDwireless150 User manual

Wireless HDMI Extender
Kit 1080p - 150m
User's Guide
G4-0062A
P/N:HDwireless150

2
Thank you for purchasing from gofanco. Our products
aim to meet all your connectivity needs wherever you
go. For optimum performance and safety, please read
the instructions carefully and keep this User's Guide for
future reference. If you need more information about
our products, please visit www.gofanco.com. For
technical support, email us at [email protected].
For drivers or manual download, please go to
www.gofanco.com/download.
Important Safety Notices
Pleasereadsafetyinstructionscarefullybeforeinstallation
and operation.
• Please pay close attention to all warnings and hints
for this device
• Do not expose this unit to rain, heavy moisture, or
liquid
• Do not put any items into the device or attempt to
modify its operation
• Do not repair the device or open the enclosure
without professional guidance to avoid electric
shocks. Doing so may void your warranty
• Keep the product in a well-ventilated location to
avoid damage from overheating
• Shut off power and make sure environment is safe
before installation
• Do not plug the HDMI cables and IR cables
in/out when the device is in use to avoid cable
damage. Make sure they are plugged into the
correct ports
• Use the included DC5V power adapters only. Make
sure the specification matches if using 3rd-party
DC power adapters

3
Introduction
The Wireless HDMI Extender Kit 1080p - 150m extends
HDMIsignals wirelessly froma source deviceto a display
device up to 150 meters. It requires no cables between the
Transmitter (TX) and Receiver (RX), making the
installation easy and clean. Great for homes and offices.
Note: Wireless transmission distance will vary due
to the environmental conditions. Thick walls, brick,
glass or electronic interference will shorten the
wireless transmission distance or cause signal loss.
Features
• Transmits HDMI signals in 1080p up to 150 meters
wirelessly
• Supports IR remote control function to control the
source device from long distances
• No cables required between Transmitter (TX) and
Receiver (RX)
• Easy and clean installation

4
PackageContents
IR Blaster Extension
Cable (1pc)
Receiver (RX) (1pc) DC5V/2A Power
Adapter (2pcs)
Transmitter (TX) (1pc)
IR Receiver Extension
Cable (1pc)
User's Guide (1pc)
Installation Requirements
1. HDMI source device (DVD player, set top box, PC,
etc.)
2. HDMI display device (SDTV/Monitor, HDTV/
Monitor, projector, etc.)
3. HDMI cables (not included)
Antenna (4pcs)

5
Product Layout
Figure 1: Transmitter (TX)
Figure 2: Receiver (RX)
1. HDMI Input Connects to the HDMI source device
2. Pairing Button Press and hold down to begin pairing process
3. IR Output Connects to the IR Blaster Extension Cable
4. Reset Button Press the button to reset the Transmitter
5. USB Port Firmware upgrade
6. Power Adapter Jack Connects to the included power adapter
1. HDMI Output Connects to the HDMI display device
2. Pairing Button Press and hold down to begin pairing process
3. IR Input Connects to the IR Receiver Extension Cable
4. Reset Button Press the button to reset the Receiver
5. USB Port Firmware upgrade
6. Power Adapter Jack Connects to the included power adapter

6
Hardware Installation
1. Power off all devices including your HDMI source
and HDMI display.
2. Install the included antennas to the TX and RX.
3. Connect your HDMI source device to the
Transmitter'sHDMIInputconnectorwithanHDMI
cable (HDMI cable not included).
4. Optional: Connect the IR Blaster Extension Cable
to the Transmitter's IR interface port. Face the eye
towards your HDMI source device's IR window.
This connection is needed only if you need to
control your HDMI source from the remote
location.
5. Connect your HDMI display to the Receiver's
HDMI Output connector with an HDMI cable
(HDMI cable not included).
6. Optional: Connect the IR Receiver Extension Cable
to the Receiver's IR interface port. This connection
is needed only if you need to control your HDMI
source from the remote location.
7. Plug the included power adapters into the
Transmitter's and Receiver's Power Jacks, then
plug both power adapters into reliable power
outlets.
8. Power on your HDMI source device and HDMI
display.The wireless extender is ready for use.
Note: For optimal signal range, install in a clear
environmentwith few obstacles. Wireless signals
from other devices, such as microwaves, wireless
mice and keyboards, etc. may interfere with
transmission. Contactour technical supportteam
if you have specific questions.

7
ApplicationDiagram
Transmitter (TX) Receiver (RX)
IR Blaster IR Receiver
DisplayHDMI source
Pairing Instructions
This kit has been paired at the factory during
manufacturing. If the units are not operating properly,
please use the steps below for pairing them.
1. Power on the transmitter and receiver units.
2. Press and hold down the pairing button on both the
transmitter and receiver at the same time.
3. When the LEDs begin to flash release both buttons.
4. When the LEDs turn solid blue color, the pairing is
successful. Repeat the pairing instructions if the
LED does not turn solid blue color.
Figure 3: Application Diagram

8
Notice
• Wireless signals transmitted through walls, glass,
brick or other solid objects will cause signal loss
and decrease the transmission distance
• Externalwireless signals frommicrowaves, wireless
mice and wireless keyboards will interfere with
HDMI signal transmission
• Keep the unit in a well ventilated environment to
prevent it from overheating
•DO NOT exposetheunit to rain,moisture, or liquids
•DO NOT place anything on the unit
•DO NOT open the housing, doing so will void the
warranty and may cause personal injury due to
electronic hazard
•DO NOT plug-in or remove the IR extension cables
when the unit is powered on

9
FAQ & Troubleshooting
Q: My display shows "Searching TX..." on the screen?
A: 1) Please check if the power adapters of Transmitter
(TX) and Receiver (RX) are connected and powered
on.
2) Check the HDMI cables for solid connection.
3) Press the Reset button on both TX and RX.
4) Connect the source device directly to the TV to
see if there is a signal.
Q: Poor video quality:
A: 1) Check the HDMI cables are connected properly.
Use different HDMI cables if necessary.
2)Changetheangleof the antenna on the transmitter
unit and receiver unit. Generally, the antenna angle
should be positioned as far apart as possible.
3)Adjustthepositionoftransmitter unit and receiver
unit, and make sure they are within the required
signal range.
4) Press the "Reset" button on the transmitter unit
and receiver unit and reconnect.
5) Remove other wireless signals and move any
obstacles that are blocking the signal line-of-sight.
6) Decrease the distance between the transmitter
unit and the receiver unit.

10
Specifications
Item Specification
Wireless Frequency 5.1 - 5.8GHz
Wireless Latency <180ms
Resolution (Input & Output)
480i@60Hz, 480P@60Hz, 576i@50Hz,
576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@24/30/50/60Hz
Antenna Gain 5dBi
IR Remote Control Supports 20kHz~60kHz IR remote devices
Transmission Distance Up to 150 meters
Operating Temperature 32° - 104° F (0° - 40° C)
Power Adapter Output: DC5V/2A
Power Consumption TX: <8W / RX: <5W
Housing Material Metal
Product Dimensions (TX & RX) 5.88" (L) x 3.64" (W) x 0.91" (H)
Weight TX: 0.81 lbs / RX: 0.81 lbs
Color Black