golmar Stadio Plus T5000EN User manual

Stadio Plus
T5000EN
rev.0105
Video Kit
digital installation
Instructions manual
Golmar se reserva el derecho a cualquier modificación sin previo aviso.
Golmar se réserve le droit de toute modification sans préavis.
Golmar reserves the right to make any modifications without prior notice.
[email protected]
www.golmar.es

2
1
Introduction ........................................1
Index....................................................1
Starting recommendations ...............1
System characteristics .......................2
System operation................................2
Important notice.................................2
Door panel installation .........................
Embedding box positioning............3
Door panel fixing ..............................4
Door panel settings ...................5 to 6
EL560 optional module ....................6
Final adjustments .............................7
Power supply installation....................8
Lock release installation.....................8
Platea Plus monitor ...............................
Description .......................................9
Function push buttons ...................10
EL561 module .................................11
End of line resistor ...........................11
Front film replacement ..................11
Monitor connector description.....12
Monitor installation.........................13
Programming .................................14
T-940 Plus telephone.............................
Description .....................................15
Function push buttons ...................15
Telephone installation ...................16
Programming .................................17
Installation diagrams............................
Door panel push buttons wiring ....18
Sections charts ...............................18
Video installation with coaxial ..19 to
20
Video installation without coaxial 21
to 22
Optional connections..........................
External lock release activation....23
Auxiliary devices activation ..........23
Intercom function ..........................24
TV connection ................................24
2nd camera activation .................25
Door bell push button connection25
Connection of an a.c. lock release
26
Troubleshooting hints........................26
SYSTEM CHARACTERISTICS
SYSTEM OPERATION
INTRODUCTION
STARTING RECOMMENDATIONS
INDEX
First of all we would like to thank and congratulate you for the purchase of this
product manufactured by Golmar.
The commitment to reach the satisfaction of our customers is stated through the
ISO-9001 certification and for the manufacturing of products like this one.
Its advanced technology and exacting quality control will do that customers and
users enjoy with the legion of features this system offers. To obtain the maximum profit of
these features and a properly wired installation, we kindly recommend you to expend a
few minutes of your time to read this manual.
O
O
O
O
O
Do not use excessive force when tightening the power supply connector screws.
Install the equipment without the power connected. Disconnect from power before
any system modification. Check that the input voltage is lower than 230Va.c.
Before to connect the system, check the connections between door panel,
monitors and telephones, and the transformer connection. Do always follow the
enclosed information.
Each time the power supply is restarted, or after a modification, the system will
remain blocked during 45 seconds.
Always use RG-59 or RG-11 coaxial cables. Never use coaxial antenna cable. In
installations no longers than 100m., Golmar RAP-5130 cable can be used.
OTo make a call the visitor should press the push button corresponding to the
apartment he wishes to contact. An acoustic tone will be heard confirming the call
is in progress once the push button has been pressed. At this moment the call will
be received at the monitor (telephone) in the dwelling. During the call the visitor
can correct his call by pressing a push button corresponding to a different
apartment, in which case the original call is cancelled.
OIn systems with several access doors, the other(s) door panel(s) will be automatically
disconnected: if a visitor tries to call from other door panel an acoustic tone will be
heard confirming the system is busy.
OThe call tone will be reproduced on the monitor during 3 seconds: after this time the
picture will appear on the master monitor without the visitor being aware of this. To
see the picture in a slave monitor press the push button, dissapearing the picture
on the other monitor. If the call is not answered in 45 seconds, the system will be
freed.
OTo establish communication pick up the monitor (telephone) handset. The
communication will last for one and a half minutes or until the handset is replaced.
Once the communication has finished the system will be freed.
OTo open the door, press the door release push button during call or communication
progresses: with one press, the door release operates during 3 seconds. During the
O
O
O
O
O
O
O
w
w
w
w
w
w
w
Microprocessed system with 3 common wires plus coaxial cable installation or 4
common wires plus twisted pair (only for kits /SC).
Fully compatible with 'Stadio' audio systems of 4 common wires installation.
Unlimited number of door panels being not necessary the use of switching units.
Acoustic busy channel and call acknowledgement signals.
d.c. lock releases activation.
Timed door open activation.
In Platea Plus monitors or T-940 Plus telephones:
Privacy on audio and video communications.
'Video-Spy' function remaining the communication channel free.
Intercommunication function with other monitor or telephone of the same
apartment.
Input for door bell apartment push button.
Different call reception tones depending where the call is comming from: main or
slave door panels, door bell push button, intercom, ...
Activation of two auxiliary devices: secondary telecamera, courtesy light, ...
Up to 2 monitors and 1 telephone in the same apartment without additional power
IMPORTANT NOTICE
One way systems are delivered fully programmed.
Wire the door panel push buttons as it is shown on page 18.
In case of two ways systems it will be only necessary to program the monitor
which will be called through the left push button.

4
3
DOOR PANEL INSTALLATION DOOR PANEL INSTALLATION
Link the sound module with the EL500
microprocessed circuit by using
the supplied flat cable.
ssembling the EL500 microprocessed
Acircuit.
The EL500 circuit is to be assembled on the top
of the embedding box. Insert the circuit in
the top flanges of the embedding box (1).
Push-in the circuit in the bottom flanges (2)
by pressing the pcb board.
1
2
1650
1850
1450
mbedding box positioning.
E
The upper part of the door panel should be placed at 1,65m. height roughly.
The hole dimensions are: 125(W) x 140(Al) x 57(D) mm.
The door panel has been designed to be placed under most of the environmental conditions.
However it's recommended to take additional cautions like rainproof covers. To obtain
a good quality picture on video door entry systems, avoid direct incidence from light sources.
Break the bottom flange
to pass the cables through.
reparing the
Pembedding box.
Pass the wiring through the hole made in
the bottom part of the embedding box.
Level and flush the embedding box.
Once the embedding box is placed,
remove the protective labels
from the attaching door panel holes.
old the door panel on the
Hembedding box.
Select a direction to open the door panel; this selection should ease
the door panel wiring.
The opening direction will be settled through the hinges position,
that must be passed through the header clips as shown.
For example, if the hinges are placed on both clips of the lower
header, the door panel will open downwards; if they are placed
on the right clips of both headers, the door panel will open to left.
To hold the door panel on the embedding box,
insert the hinges in the embedding box lockers
as shown.

6
5
Jumper JP1 loads the installation with a communications
resistor. For a proper system operation, activate this resistor
only in the closest door panel to the backbone installation
or in the general entrance door panel (if exists).
Factory default: enabled.
Jumper JP2 selects the type of cable to be used for the video
signal: coaxial cable (RG-59 or RG-11) or twisted pair.
Twisted pair video transmission requires the use of an
EL560 module plugged in the CN4 connector.
Factory default: depending on the kit model.
Jumper JP3 selects the volume of the door panel acknowledgement
signals (call in progress, system busy and door opened).
If after starting the system it's considered that the volume is too
high, modify the jumper position.
Factory default: maximum.
Jumper JP4 selects if the door panel has telecamera or not.
In case of door panels without telecamera
(EL540 sound module), change the jumper position.
Factory default: with camera.
Enabled. Disabled.
Coaxial. Twisted pair.
Maximum. Minimum.
With camera.Without camera.
DOOR PANEL INSTALLATION DOOR PANEL INSTALLATION
inary coding of the configuration dip
Bswitch.
The switches set to OFF have null value. The values of the switches
set to ON are shown in the enclosed chart.
The building code will be calculated as the sum result of the
switches values set to ON.
Example: 64+0+16+0+4+2+1=87
Switch number:
ON value:
4
64
5
32
6
16
7
8
8
4
9
2
10
1
L560 module for video
inst
E
allations with twisted pair
Kits /SC comes with the EL560 module plugged
in the CN4 connector.
NOTE: on this type of installations the EL561 module
must be plugged in all the monitors.
Refer to the specific installation diagram.
escription of the configuration dip
Dswitch.
Set to ON the switch number 2 for monitor or telephones
programming. Once the programming progress is finished
return the switch to OFF position. The programming process
is described on pages 14 (monitors) and 17 (telephones).
Set to OFF the switch number 3 in case of a master door panel.
Each system must have only one master door panel; the rest
must be slaves (ON). In systems with general entrance panel
set as master one door panel of each internal chalet.
Switches number 4 to 10 set the building code. In systems with several
door panels, set the same code in all the panels; in systems with
general entrance panel, set different codes for each internal chalet.
Valid codes are from 0 (factory default) to 99. To set the code use
binary coding as shown on the next paragraph.
Coming from previous page
escription of the configuration dip
Dswitch.
The SW1 configuration dip switch is accessible by opening
the terminal connector protection cover.
Switch number 1 allows to activate the autoswitch-on function
(audio and video communication without previous call)
at the door panel that has this switch to ON position.
In systems with several door panels activate this function
only in one of them; in systems with general entrance panel
this function can be activated in one door panel of each
internal chalet.
Continue
escription of the configuration
Djumpers.
The JP1, JP2, JP3 and JP4 configuration jumpers
(from left to right respectively) are placed on the
left side of the EL500 circuit, and are accessible
by opening the terminal connector protection cover.

8
7
DOOR PANEL INSTALLATION
lace the nameplate labels.
P
Open the label holder.
Place the label and
close.
lose the door
Cpanel.
Fix the door panel by using the supplied
screws.
Finish the door panel assembly by pressing
the closing heads.
LOCK RELEASE INSTALLATION
nstalling the FA-805 power supply.
I
If the lock release will be installed in a metal door, use a
Ø3,5mm. drill and tap the hole. In case of wood door,
use a Ø3mm. drill.
IMPORTANT: the lock release to be used must be of 12Vd.c.
If you are using a.c. lock releases,
use one R-3 relay unit as it is shown on page 26.
IMPORTANT:
IMPORTANT:
M 4 x 8
f3,5 x 25
DIN-7972
DIN-963
POWER SUPPLY INSTALLATION
To install the power supply directly on the wall, drill two holes
of Ø6mm. and insert the wallplugs.
Fix the transformer with the specified screws.
The power supply can be installed on a
DIN 46277 guide simply pressing it.
To disassemble the power supply from
the DIN guide, use a plain screwdriver
to lever the flange as shown on the picture.
The FA-805 power supply uses 7 units over DIN guide.
Remember to protect the input terminals with the supplied cover.
The power supply must be installed in a dry and
protected place. It's recommended to protect
the power supply by using a thermo-magnetic
circuit breaker and to use a ground connection.
ock release
Linstallation.
inal
Fadjustments.
If after starting the system it's considered that the audio
volume isn't correct, proceed with the necessary
adjustments as shown.
The telecamera has a pan and tilt mechanism built in
to adjust the telecamera position.
In case of low light conditions, an external illumination
can be activated by connecting a R-3 relay
between terminals '+H' and 'L2' of the sound module.
DIN 46277
f3,5 x 50
DIN-7971
f3,5 x 50
DIN-7971

10
9
On-Off push button. After any monitor reset and during the next 45 seconds,
all the monitor functions will be disabled, with the exception of call reception.
If the handset is on the craddle allows the activation of an optional second camera (*).
If not, allows to make an intercom call or to activate the second camera (*).
If the handset is on the craddle allows the activation of an optional device. If not,
allows to call to a slave porter's exchange (*) or to activate the optional device.
If the handset is on the craddle allows to see the picture from the master door panel.
If not, allows to establish audio and video communication with the door panel
that has been configurated with the autoswitch-on function. This function is
disabled if a communication is already established.
If the handset is on the craddle sends a panic call to the porter's exchanges that
have enabled the reception of this type of call. If not, allows to call to the master
porter's exchange. During call reception and communication progresses allows
the lock release activation.
Monitor
Modelo
CODIGO / CODE
MASTER
18Vdc ± 2V
Standby 15mA
Máximo 450mA
Sistemas de comunicación S.A.
Made in Spain
10ºC + 50ºC
SLAVE
INTER A1 PUERTAESCALERA
ATENCIÓN
Alta tensión. No abrir la tapa.
Manipular sólo por personal
del servicio técnico.
WARNING
High voltage. Don't open cover.
Handle only by technical service.
PISO
Floor DoorStair
PLATEA Plus
0000000000
Nº serie
af
g
b
e
jlk m
d
i
c
h
a.
b.
c.
d.
e.
f .
g.
h.
i .
j .
k.
l .
m.
Handset.
B/W or color screen (depending on the model).
Front film.
Function push buttons.
Cord.
Attachment holes.
Identification label.
Connecting points.
CN4 connector.
Three positions call reception volume control.
Cable slot.
Contrast control (color control in case of color screen).
Brightness control.
Monitor
Modelo
CODIGO / CODE
MASTER
18Vdc ± 2V
Standby 15mA
Máximo 450mA
Sistemas de comunicación S.A.
Made in Spain
10ºC + 50ºC
SLAVE
INTER A1 PUERTAESCALERA
ATENCIÓN
Alta tensión. No abrir la tapa.
Manipular sólo por personal
del servicio técnico.
WARNING
High voltage. Don't open cover.
Handle only by technical service.
PISO
Floor DoorStair
PLATEA Plus
0000000000
Nº serie
(*) Second camera activation and call to a slave porter's exchange functions require an internal
modification of the monitor. If any of these functions are required, contact with your nearest
authorized distributor.
Second camera activation disables the intercomm function and call function to a slave
porter's exchange disables optional device function.
MONITOR DESCRIPTION MONITOR DESCRIPTION
escription of the Platea Plus
Dmonitor.
unction push buttons.
F
escription of the identification
Dlabel.
For an easiest repair, replacement or increasement
of the existing monitors, fill the indentifying label
information.
MASTER: master monitor.
SLAVE: slave monitor.
INTER: slave monitor with intercom function.
A1: monitor connected to an auxiliary device.
CODE: push button code (see page 18).
STAIR: chalet code (see page 6).

11 12
Vin
Vout
Malla
Shield
Malla
Shield
A
HZ-
INT
SA
CTO
2C
A1
VP
MP
D
REF
RCPL-PLUS
LOTE
CODE 11758882
Colocar la parte superior de la regleta a 1,60m. del suelo.
Place the top part of the monitor connector at 1,60m. from the floor.
50mm.
50mm.
Presionar para abrir.
Press to open.
Terminals +, – and Malla (shield) are duplicated for easiest cascade installation of parallel
monitors or telephones. If the first monitor is not placed on the connector, cascade units
will not be powered.
escription of the RCPL-Plus
Dmonitor connector.
a
a
b
b
f
e
d
c
a. Wall attachment hole (x4).
b. Monitor attachment hook (x2).
c. Vertical wiring input.
d. Attachment clip.
e. Wiring input hole.
f. Installation terminals: positive, ground.
video signal coaxial input.
coaxial shield.
video signal coaxial output.
audio communication.
digital communication.
door bell push button input.
intercom.
auxiliary calling device output.
video distributor activation output.
2nd camera activation output.
optional device activation output.
twisted pair video signal.
+, –:
Vin :
Malla:
Vout :
A :
D :
HZ- :
INT :
SA :
CTO :
2C :
A1 :
Vp, Mp :
L561
inst
E
allations with twisted pair
module for video
The monitors included in kits /SC come with the EL561 module
plugged in the CN4 connector, that's placed in the monitor base.
NOTE: on this type of installations the EL560 module must be
plugged in the EL500 microprocessed circuit (page 6).
Refer to the specific installation diagram.
andling the end of line jumper.
H
hanging the front film.
C
The end of line jumper is placed on the CN4 connector, that can be
located on the monitor base.
In case of twisted pair cable installations, the end of line jumper
is placed in the EL561 module, also located in the CN4 connector
of the monitor base.
Do not remove the jumper on monitors where the video cable finish.
Remove the jumper on monitors where the video cable continue.
The monitor is supplied with a reversible front film, that allow the owner
to choose between two colors.
To change the front film, remove the front plate by inserting a plain screwdriver
in the triangle marks, as it is shown on the drawing.
MONITOR ADJUSTMENTS MONITOR CONNECTOR DESCRIPTION

13 14
Avoid to place the monitor near to heating sources,
in dusty locations or smoky environments.
To install the monitor directly over the wall,
drill two holes of Ø6mm. and use the supplied screws.
The upper part of the monitor connector must be placed
at 1,60m. height roughly. The minimum distance
between the monitor connector and the closest object
must be 5cm.
Place the monitor at right angles to the connector
and align the attaching holes of the monitor
with the attachment hooks of the connector,
as it is shown on the drawing.
Lock out the monitor. Press the right side
till the attachment clip locks the monitor
firmly.
To disassemble the monitor from the connector,
use a plain screwdriver to release the
attachment clip. Remove the monitor from
the connector, with special attention do not
falls.
MONITOR INSTALLATION MONITORS PROGRAMMING
ix the monitor connector to the
Fwall.
ix the monitor.
F
Set to ON the switch number 2 of the configuration dip switch, that's
accessible by opening the terminal connector protection cover.
The door panel will reproduce a sound to advise that the system
has entered into programming mode.
In systems with more than one door panel, the programming process
shall be done on the master door panel only.
Switch off the monitor to be programmed.
Once the monitor is off, press the door release push button.
With the door release push button pressed
switch on the monitor.
To show that the system is ready for programming,
the door panel will reproduce a sound and the picture
will appears on the monitor. At this moment, the door
release push button can be released. Lift the handset
to establish audio communication with the door panel.
Press the door panel push button that will
call to this monitor. At this moment
the door panel will reproduce a sound
and the monitor led will blink.
To program the monitor as master, switch it
off and on again.
To program it as slave, press the door
release push button.
To program it as slave with intercom
function press the push button.
Each apartment must have one master unit only; in case of parallel units configure them
as slaves, both monitors or telephones.
Make a call to check that the monitor has been succesfully programmed.
Repeat these steps to program the rest of monitors.
Once the programming has been finished, set to OFF the programming
switch. If you don't, the door panel will reproduce a sound to advise
that the system is still into programming mode.
rogramming the
Pmonitors.

TELEPHONE DESCRIPTION TELEPHONE DESCRIPTION
escription of the T-940 Plus
Dtelephone.
a.
b.
c.
d.
e.
f.
g.
h.
i.
Telephone handset.
Speaker grille.
Microphone hole.
Subjection hole.
Telephone cord connectors.
Function push buttons.
On-Off light indicator.
Call reception volume control.
Hook switch.
a
d
c
e
i
h
e
b
f
g
The telephone has a three positions switch placed on the bottom
part of the telephone (closest to the telephone cord connector)
that allows to control the call reception level volume.
unction push
Fbuttons.
On-Off push button.
After any telephone reset, and during the next 45 seconds,
all the telephone functions will be disabled, with the exception
of call reception.
This push button allows to make an intercom call when the handset
is not on the craddle. This function is described on page 24.
If the handset is on the craddle sends a panic call to the porter's
exchanges that have enabled the reception of this type of call.
If not, allows to call to the master porter's exchange.
During call reception and communication progresses allows
the lock release activation.
a.
b.
c.
a
b
c
erminal connector description.
Tpositive, ground.
audio, digital communication.
intercom.
auxiliary calling device output.
door bell push button input.
+ , :
A , D :
INT :
SA :
HZ- :
–
A D
+_SAINT HZ-
TELEPHONE INSTALLATION
ix the telephone.
F
It will be necessary to open the telephone for wiring and
fixing purposes. To open the telephone insert a plain
screwdriver into the slots and rotate it as shown.
Avoid to place the telephone near to
heating sources, in dusty locations or
smoky environments.
The telephone can be fixed using an
electrical embedding box or directly
on the wall, as shown on the picture.
If the telephone will be installed directly
over the wall, drill two holes of Ø6mm.
on the specified positions, using 6mm.
wallplugs and Ø3,5 x 25mm. screws.
Pass the installation wires through the corresponding hole and
connect them as shown on the installation diagrams.
Close the telephone as shown on the picture. Once the telephone
is closed, connect the handset using the telephone cord and
put it on the craddle.
15 16

1,00mm² 2,50mm²
0,25mm² 0,25mm²
RG-59 RG-59
Terminal
WITH COAXIAL CABLE
50m.
Distance
150m.
A , A , A, D
in out
V , V , V , V
in+ out+ in out
+, –, CV+, CV–
1,00mm² 2,50mm²
0,25mm² 0,25mm²
CAT-5 CAT-5
Terminal
WITH TWISTED PAIR
50m.
Distance
150m.
A , A , A, D
in out
V , V , V , M
in+,- out+,- p,d p,d
+, –, CV+, CV–CTO, CT,
17 18 INSTALLATION DIAGRAMS
TELEPHONES PROGRAMMING
rogramming the
Ptelephones.
Set to ON the switch number 2 of the configuration dip switch, that's
accessible by opening the terminal connector protection cover.
The door panel will reproduce a sound to advise that the system
has entered into programming mode.
In systems with more than one door panel, the programming process
shall be done on the master door panel only.
Switch off the telephone to be programmed.
Once the telephone is off, press the door release push button.
With the door release push button pressed
switch on the telephone.
To show that the system is ready for programming,
the door panel will reproduce a sound and
the telephone led will blink. At this moment, the door
release push button can be released. Lift the handset
to establish audio communication with the door panel.
Press the door panel push button that will
call to this telephone. At this moment
the door panel will reproduce a sound
and the telephone led will blink.
To program the telephone as master,
switch it off and on again.
To program it as slave, press the door
release push button.
To program it as slave with intercom
function press the center push button.
Each apartment must have one master unit only; in case of parallel units configure them
as slaves, both monitors or telephones.
Make a call to check that the telephone has been succesfully programmed.
Repeat these steps to program the rest of telephones.
Once the programming has been finished, set to OFF the programming
switch. If you don't, the door panel will reproduce a sound to advise
that the system is still into programming mode.
Connect the push buttons in the CN2 connector terminal
of the EL500 circuit as shown. Connect the CP terminal
to the push buttons common terminal.
To avoid short-circuits, use wires of 0,25mm² section
to wire the push buttons.
IMPORTANT NOTICE.
Right push button must be connected to P8 terminal.
P8 P7 P6
CN2
P5 P4 P3 P2 P1CPB
ections charts.
S
ush buttons
Pwiring.
To the push buttons common terminal.
To the 1st push button (code 106).
To the 2nd push button (code 1) (only two ways kits).

Cascade installation example.
Remove the jumper from the CN4 connector in all
the monitors (see page 11), except on the one
where the video cable finishes (don't uses
the video output).
Distributed installation example.
Remove JP1 jumper on all the video distributors
and monitors (see page 11), except on the ones
where the video cable finishes (don't use
the video output).
IMPORTANT.
If the system has one door panel only,
override the wiring to the second door panel.
If the system has more than one door panel, wire
the rest of panels as shown on the diagram.
19 20
JP JP
SW1 SW1
Slave video door panel Master video door panel
4321 4321
CV+ CV+CV- CV-D D
Malla Malla
Vin- Vin-Ain AinAout AoutVin+ Vin+Vout- Vout-Vout+ Vout++ +
CN1 CN1
- -
A
+_D
ED1 D2
+
D4L-PLUS
A
_
+D
Malla
Vin Vout
CN4
A
_
+D
Malla
Vin Vout
CN4
A
_
+D
Malla
Vin Vout
CN4
A
_
+D
Malla
Vin Vout
CN4
JP1
A
_
+D
Malla
Vin Vout
CN4
FA-805
SEC
PRI
Main
+
--
~1~1 ~2
0 110 230
FA-805
SEC
PRI
Main
+
--
~1~1 ~2
0 110 230
INSTALLATION DIAGRAMS
ne or several accesses
Owith coaxial cable.

Cascade installation example.
Remove JP1 jumper from all of the EL561 monitor
modules (see page 11), except on the one
where the twisted pair cable finishes
(don't uses the video output).
Remove JP1 jumper from all of the video distributors
and EL561 monitor modules (see page 11),
except on the ones where the twisted pair cable
finishes (don't use the video output).
Don't modify the JP2 jumper of the video distributors.
Distributed installation example.
IMPORTANT.
If the system has one door panel only,
override the wiring to the second door panel.
If the system has more than one door panel, wire
the rest of panels as shown on the diagram.
21 22 INSTALLATION DIAGRAMS
JP JP
SW1 SW1
Slave video door panel Master video door panel
4321 4321
CV+ CV+CV- CV-D D
Malla Malla
Vin- Vin-Ain AinAout AoutVin+ Vin+Vout- Vout-Vout+ Vout++ +
CN1 CN1
- -
A
+_D
VpMp
A D
_
+
JP2 JP1
A
A
D
D
CT +
+
Vpi
Vd1
Mpi
Md1
_
_
A
D
CT
+
Vd2
Md2
_
A D+ Vpo Mpo
_
D2L-Plus/2H
EL561
JP1
VpMp
A D
_
+
EL561
JP1
VpMp
A D
_
+
EL561
JP1
VpMp
A D
_
+
EL561
JP1 VpMp
A D
_
+
EL561
JP1
FA-805
SEC
PRI
Main
+
--
~1~1 ~2
0 110 230
FA-805
SEC
PRI
Main
+
--
~1~1 ~2
0 110 230
ne or several accesses
Owith twisted pair.

SA
+T TR RM M
SAR-90
23 24
CV+CV-
-
A
+_D INT
A
_
+D A1
Malla
Vin Vout
CN4
A
_
+D INT
Malla
Vin Vout
CN4
A
_
+D
Malla
Vin Vout
CN4
OPTIONAL CONNECTIONS OPTIONAL CONNECTIONS
The lock release can be activated at any moment
by using an external push button, that must be
connected between 'CV ' y ' ' terminals of the
EL500 circuit. This function will allows to exit from the
chalet being not necessary the use of a key.
– –
xternal lock release
Eactivation.
uxiliary devices activation.
A
To activate auxiliary devices the use of a SAR-90 relay unit will be required. If this device is
shared for all the monitors, link their A1 terminal and use just one relay unit.
In case that each monitor has its own application use a SAR-90 relay unit for each monitor
and don't link the A1 monitor terminals.
To activate this function, press monitor push button at any moment with no dependence of
the handset position.
Usual applications are the activation of stairs light, second lock release, ...
To stairs light push button
onnecting the Shiner Plus
Cmonitor to a video recorder
ntercom function.
I
Platea Plus monitor and T-940 Plus telephone have intercom facility between two units of the
same apartment. To enable this function check the following conditions:
- One of the units has been configurated as master and the other unit as slave with
intercom, as described on pages 14 and 17.
In case to intercom one monitor with one telephone, configure the monitor as master..
- Link the INT terminal of the units, as it is shown on the enclosed diagram.
To establish an intercom communication lift the handset and press the intercom push button;
acoustic tones will be reproduced on the handset confirming the call is in progress or
that the other unit is communicating with the door panel. To establish communication lift
the handset of the called unit. If during an intercom communication a call is made from
the door panel, acoustic tones will be heard on the master unit handset and the picture
will appear in case of a monitor; press the intercom push button of the master unit
to establish communication with the door panel, or press the door release push button to
activate the lock release.
The reproduced acoustic tones are different depending on their provenance, that allows the
user to distinguish where the call is made from.
If your TV or video recorder have a SCART
connector, it will be possible to view
the picture from the door panel on the TV
screen.
Remove the end of line jumper, that's placed on the
CN4 connector. Connect the coaxial cable
between terminals 17 (shield) and 20 (hot)
of the SCART connector.
Use ~1 and ~2 power supply outputs to activate a second lock release.
IMPORTANT: this second lock release must be 12Va.c. type.
SA
+T TR RM M
SAR-90
A
_
+D A1
Malla
Vin Vout
CN4
FA-805
SEC
PRI
Main
+
--
~1~1 ~2
0 110 230

25 26
OPTIONAL CONNECTIONS OPTIONAL CONNECTIONS
HZ-
-
oor bell push button connection.
D
The Platea Plus monitor and the T-940 Plus telephone can be used to receive the calls made
from the apartment door, saving the use of a bell. Wire the push button of the apartment
door to the 'HZ ' and ' ' monitor or telephone terminals.
The reproduced acoustic tones are different depending on their provenance, that allows the
user to distinguish where the call is made from. If during a conversation a call is made from
the apartment door, acoustic tones will be reproduced on the hanset to advise that someone
is calling.
– –
ctivation of a second
Acamera.
The use of a SAR-90 relay will be required to activate a second camera and an internal
modification on the monitor shall be done, as it's described on page 10.
This facility disables the intercom function. If both functions are required, use A1 terminal to
activate the second camera.
To activate this function, press monitor push button at any moment with no dependence of
the handset position.
If this device is shared for all the monitors, link their 2C terminal and use just one relay unit.
In case that each monitor has its own camera use a SAR-90 relay unit for each monitor
and don't link the 2C monitor terminals.
This push button can be used to activate other auxiliary devices, as the A1 terminal is used.
Usual applications are the surveillance of the elevator entrance, reception hall, ...
onnexion of an a.c. lock
Crelease.
As it is described on page 8, the lock release
to be connected to the door panel
must be d.c. type. If an a.c. lock release
has been installed before, use a R-3
relay unit and connect them to the EL500
circuit as it is shown on the enclosed diagram.
TROUBLESHOOTING HINTS
An easy way to check that the system is working properly is to disconnect the
wiring from the door panel and to check the monitor directly connected to the EL500
circuit.
No shortcircuit will damage the connected units, with the exception of a
shortcircuit between CTO and ' ' monitor or distributor terminals.
ONothing operates.
wCheck the output power supply voltage between ' ' and '+' terminals: it should
have 17,5 to 18,5Vd.c. If not, disconnect the power supply from the
installation and measure again. If it's correct now, it means there is a short
circuit in the installation: disconnect the power supply from mains and check
the installation.
wCheck that 'D' terminal is not shortcircuited with ' ' or '+' terminals.
wCheck that 'D' terminal hasn't been changed by 'A' terminal somewhere in the
installation.
wIf these tests don't solve the problem, check the voltage between 'B' and 'CP'
terminals of the EL500 circuit; if the measured voltage is different to 12Vd.c.
change the EL500 circuit.
OInappropriate audio level.
wAdjust the level volumes as shown on page 7. In case of feedback, reduce the
audio levels until feedback fade out. If feedback don't dissapears refer to the
following hint.
OContinuous audio feedback.
wCheck that 'A' terminal is not shortcircuited with other terminals.
ODoor open function no operates.
wRemember that this function is only available during call and communication
progresses.
wDisconnect the lock release from the EL500 circuit and short-circuit terminals ' '
and 'CV ': at that moment the output voltage between terminals 'CV+' y
'CV ' should be 12Vd.c. If it's so check the lock release and its wiring.
OThe system cannot be programmed.
wCheck that the switch number 2 of the configuration dip switch is set to ON (see
page 6) and that the programming steps are correctly followed.
wCheck that 'D' terminal is not shortcircuited with other terminals.
OSome units don't receive calls.
–
–
–
–
–
–
SA
+T TR RM M
SAR-90
A
_
+D 2C
Malla
Vin Vout
CN4
MRBO T
R-3
CV+CV-
FA-805
SEC
+
--
~1~1 ~2