Lanpro LP-349 User manual

Wireless - Equipment
www.lanpro.com
LP-349 123 Manual in AP Mode.
LP349_M123_ENE01W
LP-349
123 Manual in AP Mode.

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-349 123 Manual in AP Mode
2
The following Instruction Manual will guide you on how to congure the LP-349 in AP Mode.
Figure 1
1
2
3
Once the Setup 123 Manual has been executed, proceed to
congure it by rst connecting the UTP cable that comes
from the LP-349 to the To Odu port of the PoE Injector
furnished with the radio as shown in gure 1.
Connect an UTP cable from the To Ethernet port of the PoE
injector to the Switch or PC as shown in gure 2.
Figure 2
4
Connect electric power to the PoE injector as shown
in figure 3.
Please go to your network card properties window and
select: Internet Protocol, then select: Properties, as
shown in gure 4.
Figure 3
Figure 4

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-349 123 Manual in AP Mode
3
5
In the window shown in gure 5, select: Use the following
IP address and input an IP address in the range of IP set
by default of the LP-349. In this example, we have selected
address: 192.168.1.201, the LP-349 has a default address
of: 192.168.1.1, input 255,255,255,0 in: Subnet Mask, in:
Default gateway input the destination router address, in:
Preferred DNS Server you must input the DNS address of
your service provider or the IP address of your destination
router, the one that provides the Internet Service, this is
will route any corresponding queries to the router of the
destination network.
Figure 5
6
7
Please open your preferred browser and input the default address: 192.168.1.1, please see gure 6.
In the certicate validation window shown in gure 7, please accept by selecting: Continue to this website (not
recommended).
Figure 6
Figure 7

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-349 123 Manual in AP Mode
4
8
In the window shown in gure 8, input the word admin in:
Name and the word: password in: Password and then
select: Login now.
Figure 8
9
In the window shown in gure 9 you have the option of
conguring up to eight(8) Virtual APs in the LP-349, and you
will be able to connect up to 32 clients (If you enable that
option of course) to each one of them.
By default, the LP-349 comes in AP mode, but if this is
not the case, please select option: Basic Settings in the
submenu of Wireless Setup and then select: Access Point
as shown, then select: Apply.
Figure 9
10
In the window shown in gure 10, in: SSID proceed to select:
Edit in order to congure the virtual AP’s. In this page you
will also be able to congure the channel or frequency in
which you wish to transmit, it is important to mention now
that all the VAP’s will be in the same frequency and channel.
Figure 10

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-349 123 Manual in AP Mode
5
11
In the window shown in gure 11, select the VAP you wish to
congure. Only one of them is enabled by default but without
security. Select: Edit in order to perform the change.
Figure 11
12
In gure 12, the options for conguring the rst Virtual AP
or VAP.
Figure 12
13
In the window shown in gure 13, input in: SSID the name
you wish to assign to the rst VAP. Select the encryption
mode desired and the appropriate Key. In the option: Max
Station Number(1-32) you will be able to limit the number
of concurrent clients that can connect to this VAP , this is with
the intention of having a better performance of the equipment
and to establish a better control over them. Select then:
Apply to apply the changes.
Figure 13

www.lanpro.com
Wireless - Equipment - 2.4 GHz - LP-349 123 Manual in AP Mode
14
It is important to mention that all the VAP’s will share the
set of Keys in WEP, being only able to change the key for
authentication and encryption to be used by default. In order
to enable another VAP, you must set: Enable and then:
Apply as shown in gure 14, then proceed to congure the
security by repeating paragraphs 11, 12 and 13 for this VAP.
Figure 14
15
In the window shown in gure 15, proceed to change the
administration password of the equipment. Even though it
is not mandatory, we highly recommend that you change
the administration password of your equipment. We must
remind you to store it in a safe place to which you can
have access in the event that you forget it. If you lose
it, you must reset the equipment to factory values and
lose any setup you have made. Please use for this the
123 manual on how to reset to factory values, document:
LP348_M123_ENC01W.
In order to change the password, please select option:
Change Password, located in the menu: Management
as shown in the gure 15.
Figure 15
16
Figure 16
6
In the window shown in gure 16, input in: Current
Password the old password, in: New Password, the
new password you want to use, in the eld: Repeat New
Password, do as indicated and the select: Apply.