Alcatel-Lucent 4080 IP-DECT User manual

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 - July 2011

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 2
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-
Lucent. All other trademarks are the property of their respective owners. The information
presented is subject to change without notice. Alcatel-Lucent assumes no responsibility
for inaccuracies contained herein.
Copyright© 2011 Alcatel-Lucent. All rights reserved.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 3
Regulatory information European Union
Declaration of Conformity
This equipment is in compliance with the essential requirements of R&TTE
Directive 1999/5/EC.The Declaration of Conformity may be obtained from your
installer.
PRODUCT DISPOSAL INFORMATION (EN)
For countries in the European Union
The sy
mbol depicted here has been affixed to your product
in order to inform you that electrical and electronic
products should not be disposed of as municipal waste.
Electrical and electronic products including the cables, plugs and
accessories should be disposed of separately in order to allow proper
treatment, recovery and recycling. These products should be brought to
a designated facility where the best available treatment, recovery and
recycling techniques is available. Separate disposal has significant
advantages: valuable materials can be re-used and it prevents the
dispersion of unwanted substances into the municipal waste stream.
This contributes to the protection of human health and the environment.
Please be informed that a fine may be imposed for illegal disposal of electrical and
electronic products via the general municipal waste stream.
In order to facilitate separate disposal and environmentally sound recycling arrangements
have been made for local collection and recycling. In case your electrical and electronic
products need to be disposed of please refer to your supplier or the contractual
agreements that your company has made upon acquisition of these products.
For countries outside the European Union
Disposal of electrical and electronic products in countries outside the European Union
should be done in line with the local regulations. If no arrangement has been made with
your supplier, please contact the local authorities for further information.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 4
•Reorient or relocate the equipment.
Regulatory information United States
This device contains functions which are not operational in US territories
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Modifications not expressly approved by the manufacturer could void the user’s authority
to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•Increase the separation between the equipment and receiver.
•Consult the dealer or an experienced radio/TV technician for help.”
Privacy of communications may not be ensured when using this equipment.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 5
Exposure to Radio Frequency (RF) Signals:
This base station is a radio transmitter and receiver. It is designed and manufactured not
to exceed the emission limits for exposure to radio frequency (RF) energy set by the OET
Bulletin 65 Supplement C. These limits are part of comprehensive guidelines and
establish permitted levels of RF energy for the general population. The guidelines are
based on the safety standards previously set by international standards bodies. These
standards include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health.
This device with internal antennas must provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
Regulatory information Canada
Operation of this device is subject to the following two conditions: (1) this device may not
cause any interference and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Exposure to Radio Frequency (RF) Signals:
This wireless device is a radio transmitter and receiver. It is designed and manufactured
not to exceed the emission limit for exposure to radio frequency (RF) energy set by the
Ministry of Health (Canada), Safety Code 6. These limits are part of comprehensive
guidelines and established permitted levels of RF energy for the general population.
These guidelines are based on the safety standards previously set by international
standards bodies. These standards include a substantial safety margin designed to
assure the safety of all persons, regardless of age and health. This device and its
antenna must not be co-located or operating in conjunction with any other antenna or
transmitter.
Privacy of communications may not be ensured when using this equipment.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 6

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 7
CONTENTS
CONTENTS........................................................................................................................7
14080 IP-DECT GENERAL ..........................................................................................10
1.1 GENERAL.........................................................................................................10
1.2 COUNTRY SELECTION ...................................................................................10
1.3 SITE REQUIREMENTS ....................................................................................11
1.4 TEMPERATURE RANGES...............................................................................11
1.5 CABLE SPECIFICATIONS FOR 4080 IP-DECT Types.....................................11
1.6 G.729 DAUGHTER BOARD..............................................................................12
1.7 VISUAL CHECK................................................................................................12
1.8 HORIZONTAL OR VERTICAL MOUNTING ......................................................13
1.9 INSTALLATION PROCEDURES.......................................................................14
2UNPACKING..............................................................................................................15
3ADJUSTING THE ANTENNA POSITION ...................................................................16
4MOUNTING THE G.729 DAUGHTERBOARD............................................................20
5MOUNTING THE 4080 IP-DECT AGAINST A WALL .................................................23
6LEDs..........................................................................................................................26
6.1 LED Status........................................................................................................26
6.2 LED Colours......................................................................................................27
7SPECIFICATIONS......................................................................................................28

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 8
PREFACE
This manual is applicable for the 4080 IP-DECT, DECT Transceiver.
Please note that some product models or features described in this manual may
not be available in all world regions.”
No legal rights can be obtained from information in this manual.
Important:
The equipment described in this manual should be installed and maintained only by
professional and qualified engineers in accordance with the procedures and
instructions described in this manual.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 9

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 10
1 4080 IP-DECT GENERAL
1.1 GENERAL
This installation Manual is valid for installing a DECT transceiver (4080 IP-DECT) to a
wall in horizontal or vertical position. The 4080 IP-DECT is designed for indoor use.
When installing an 4080 IP-DECT outdoors, please use the dedicated Outdoor Cabinet:
Note that there are two types of DECT Transceivers::
•4080 IP-DECT Access Point Integrated antennas.
•4080 IP-DECT Access Point External antennas.
Note: The 4080 IP-DECT Access Point External antennas must always be
installed/used in the outdoor cabinet! For more information consult the manual for
the Outdoor Cabinet for 4080 IP-DECT.
1.2 COUNTRY SELECTION
The 4080 IP-DECT is equipped for EMEA, Latin America and North America. However,
the DAP Controller determines the frequency used and the power level. The DAP
Controller is the software that runs on a PC to control the 4080 IP-DECT.
There are three types of DAP Controllers available for the 4080 IP-DECT:
•DAP Controller – International.
This version is used in EMEA countries and countries that use the European
frequencies and power levels.
•DAP Controller - North America
This version is used in North America.
•DAP Controller - Selective Countries.
This version is used in countries with other frequency ranges than EMEA or North
America
Note: In North America, only the “DAP Controller - North America” will be delivered, so
no other frequencies than the North America frequencies and power levels are
possible in North America.
Note: In Europe, only the “DAP Controller - International” will be delivered, so no other
frequencies than the European frequencies and power levels are possible in
Europe.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 11
1.3 SITE REQUIREMENTS
Usually the Cabinets will be fixed to existing walls in the positions determined by the Site
Survey.
Do not mount the 4080 IP-DECT to a metal wall!
1.4 TEMPERATURE RANGES
−Temperature range 4080 IP-DECT: -5°to 45°C.
The AP400 should not be exposed to sunlight!
The outside temperature range for the 4080 IP-DECT (all types) mounted in the Outdoor
Cabinet is as follows:
−Minimum outside temperature: -20°C
−Maximum outside temperature: 45°C
The Outdoor Cabinet should not be exposed to sunlight!
1.5 CABLE SPECIFICATIONS FOR 4080 IP-DECT Types
The cabling to the 4080 IP-DECT(External antennas) is “Category 5” or “Category 6”
Ethernet cabling. The interface is defined as an SELV interface according EN60950-1.
For this reason the following safety restriction is applicable:
Caution: The cabling and/or the 4080 IP-DECT(External antennas) may never be
exposed to over-voltages (e.g. lightning). Therefore, the 4080 IP-
DECT(External antennas) and cabling associated with it may never be
installed outdoors! However there is an exception: if installed in the Outdoor
Cabinet, and the Outdoor Cabinet is mounted against a wall and the cable is
led directly indoors, it is permitted. For details about this specific installation
refer to the installation manual of the Outdoor Cabinet.
Note: Cat 7 cabling is not supported!

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 12
The power for the 4080 IP-DECT(External antennas) must be supplied via the Ethernet
cable, PoE (IEEE 802.3af). There is no room for a Mains Power adaptor inside the
Outdoor Cabinet.
1.6 G.729 DAUGHTER BOARD
The 4080 IP-DECT does support the G.729 codec, but only if the G.729 Daughter Board
is installed.
If the G.729 Daughter Board is not installed, the 4080 IP-DECT supports only G.711u law
or G.711a law.
Installation of the Daughter Board is described in chapter 4. MOUNTING THE G.729
DAUGHTERBOARD.
1.7 VISUAL CHECK
The equipment must be carefully unpacked and examined for any visible sign of damage.
Anything not in order should be reported back to the supplier, as soon as possible, to
avoid delays during installing due to missing equipment.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 13
1.8 HORIZONTAL OR VERTICAL MOUNTING
The 4080 IP-DECT can be mounted horizontally or vertically. When mounting vertically,
you don’t need to change the antenna position.
Figure 1. 4080 IP-DECT in vertical position.
When the 4080 IP-DECT must be mounted horizontally, the antenna position must be
changed.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 14
Figure 2. 4080 IP-DECT mounted horizontally
1.9 INSTALLATION PROCEDURES
The installation of an 4080 IP-DECT comprises the installation of:
−Adjusting the Antenna position (if necessary).
−Mounting the G.729 Daughter Board (if applicable)
−Mounting the 4080 IP-DECT against the wall.
Note: When you install the 4080 IP-DECT in the outdoor cabinet, please consult the
4080 IP-Dect Outdoor Cabinetisolated Installation Manual.
Note: The minimum distance between 4080 IP-DECTs (DECT Access Points) must be
more than 1 meter. (However, it is strongly recommended to respect a minimum
distance of 5 meters between the 4080 IP-DECTs.)

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 15
2 UNPACKING
PROCEDURE: “Unpacking”.
Actions
1. Open the card board box and take the 4080 IP-DECT out.
2. Open the card board box and take the 4080 IP-DECT out.
3. Check the 4080 IP-DECT on any damages.
4. Continue with one of the following Chapters:
−When you mount the 4080 IP-DECT vertically, the antenna position will normally
be OK, and when you do not need to install the G.729 Daughter Board, continue
with Chapter 5 MOUNTING THE 4080 IP-DECT AGAINST A WALL.
−When you mount the 4080 IP-DECT horizontally, you probably need to change
the antenna position. Consult Chapter 3. ADJUSTING THE ANTENNA
POSITION.
−When you require G.729 codec support, you will have to install the G.729
Daughter Board. Consult Chapter 4. MOUNTING THE G.729
DAUGHTERBOARD

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 16
3 ADJUSTING THE ANTENNA POSITION
Note: You only need to change the antenna position when you mount the 4080 IP-
DECT horizontally! In all other cases you don’t need to change the antenna
position.
Figure 3. 4080 IP-DECT mounted horizontally

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 17
PROCEDURE: “Adjusting the Antenna position”.
Note: Antenna position can be changed once. You should not change it back!
Actions
1. Remove the two screws from the rear side of the cabinet.
Figure 4. Rear side of Cabinet.
2. Open the cabinet CAREFULLY! Make sure that you shift the cover of the antenna’s
carefully from the antenna’s.
3. Take the antenna cover from the 4080 IP-DECT cover.
4. To put the antennas in vertical position, bend them carefully Figure 5.
Bend Antennas carefully into vertical position. as shown in
Screws are inside these holes

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 18
Figure 5. Bend Antennas carefully into vertical position.
5. After the antennas are put in the vertical position, close the 4080 IP-DECT cabinet
again. In other words, put the 4080 IP-DECT cover back into position and secure the
screws at the rear side of the cabinet. See Figure 6. Antennas locked into Cover.
Figure 6. Antennas locked into Cover.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 19
6. Make sure that the antennas are properly locked into the locks in the 4080 IP-DECT
cover.
Figure 7. Detail of antenna in lock.
7. Move the antenna cover carefully over the antennas in the vertical position and
make sure that the antennas do not bend. When the antenna cover is in its position,
push it further into its position in the 4080 IP-DECT cabinet to fix it.
Figure 8. Cover installed.
8. Now your 4080 IP-DECT is ready to be installed.

Alcatel-Lucent 4080 IP-DECT
Installation Manual
8AL90850USAAed01 20
4 MOUNTING THE G.729 DAUGHTERBOARD
Follow the step-by-step procedure below, to install the G.729 daughter board.
PROCEDURE: “Adjusting the Antenna position”.
Actions
1. Make sure that you have the G.729 Daughter board.
2. Open the cabinet. Use steps 4 till 6 in Chapter 3
3. Take the PWB out of the cabinet.
Note: Mind the light conductor for the LEDs. It can drop off!
Figure 9. Light conductor for LEDs
4. Now you should have the 4080 IP-DECT PWB and the G.729 Daughter Board as
separate items.
5. Remove the protection foil from the sticky part on the G.729 Daughter Board.
LED Light conductor