GoPro LCD BacPac User manual

LCD BacPac™
USER MANUAL + WARRANTY INFO

FIRMWARE UPDATE
To determine if a firmware update is required, please
follow these steps:
• With the camera fully charged, attach the LCD
BacPac™
to camera and power camera on (see
attachment instructions on page 4). If the LCD
screen powers on, you have the latest rmware
and no update is needed.
• If the LCD BacPac does not power on,
then you will need to download and install
the latest rmware for your camera at:
gopro.com/firmware.
2

LCD BACPAC FEATURES
1. Seamlessly attaches to the back of
HD HERO cameras.
2. LCD screen allows for easy visual control
of camera and settings.
3. Fast forward + fast rewind photos and video.
4. Integrated speaker for sound.
3

ASSEMBLING YOUR LCD SCREEN TO HD HERO
ATTACHING LCD BACPAC TO HD HERO
1. Slide hooked end of the BacPac (A) into the groove
on the right side of the camera body (B).
2. Push BacPac connector (C) into the HERO Bus port
(D) on the back of the camera.
REMOVING LCD BACPAC FROM HD HERO
1. Pull back on le side of BacPac marked with the
arrow to disconnect from the HERO bus port.
2. Slide hooked end of BacPac (A) out of camera
groove (B).
4

SWAPPING HOUSING DOORS
To secure the HD HERO & LCD BacPac assembly into the
housing, you will need to replace the standard back door
with one of the included extended back doors. A total of 4
doors are supplied with the LCD BacPac; 2 waterproof
doors (standard + wrist housing models) and 2
non-waterproof doors (standard and wrist housing
models). The skeleton doors allow for better audio and
camera cooling when waterproong is not needed.
1. 0pen the backdoor of the housing so that it is
hanging downwards.
2. Pull downwards on the backdoor until it snaps
free from the hinge.
3. Line up replacement backdoor into the hinge opening.
4. Push upwards on the backdoor until it clicks
into place.
5

USING THE LCD BACPAC
The camera’s default setting keeps the LCD screen
powered on. Below are options to change how the
LCD powers o.
CAMERA SET MENU OPTIONS  LCO AND LCF
Check Page 2, section “Firmware Update”, to ensure your
camera has the necessary rmware update for your LCD
screen. If so, proceed to Steps 1 & 2 below:
1. LCO (default): LCD ON. This setting keeps the LCD
screen powered on, continuously, while the camera
is on. LCD will only power o if the camera is turned
o or if you quickly press the side LCD button.
2. LCF: LCD OFF. This setting auto powers the LCD
screen o 60 seconds aer the last camera button
press. The camera will remain on and only the LCD
will power o. If recording videos or photos, the
recording will continue uninterrupted while the
screen is powered o. A quick press of any button
will power the LCD screen back on.
TURNING LCD SCREEN ON/OFF
1. Pressing the LCD button quickly will power the
screen on and o when in preview mode.
6

ADJUST LCD SCREEN BRIGHTNESS
1. Press and hold LCD button for 2 seconds to enter
LCD menu.
2. Press power/mode button twice to highlight
‘BRIGHTNESS’ menu button.
3. Press shutter button repeatedly to adjust brightness.
PLAYBACK PHOTOS
1. Press and hold LCD button for 2 seconds to enter
LCD menu.
2. Press power/mode button once to highlight
‘PHOTO’ menu option.
3. Press shutter button and the rst recorded photo
will automatically be displayed.
4. Press power/mode button to advance to the next
photo. Hold down power/mode button to fast
forward through photos.
5. Press shutter button to go back to the previous
photo. Hold down shutter button to fast reverse
through photos.
7

PLAYBACK VIDEOS
1. Press and hold LCD button to enter LCD menu.
2. ‘VIDEO’ should already be highlighted.
3. Press shutter button and the rst recorded video
will automatically start playing.
4. During video playback, press and HOLD the
power/mode button to Fast Forward the video
playback. Releasing the power/mode button will
resume normal playback.
5. During video playback, press and HOLD the shutter
button to Rewind the video playback. Releasing the
button will resume normal playback.
ADJUST SPEAKER VOLUME
1. During video playback, quickly press LCD
button repeatedly as needed to adjust the
speaker volume.
EXIT VIDEO OR PHOTO PLAYBACK MODE
1. Press and hold the LCD button for 2 seconds and
camera will switch back to normal camera mode.
8

IMPORTANT SAFETY AND
HANDLING INFORMATION
WARNING: Failure to follow these safety instructions
could result in fire, electric shock, or other injury or
damage to the LCD BacPac or other property.
HANDLING
The LCD BacPac contains sensitive components. Do not
drop, disassemble, open, crush, bend, deform, puncture,
shred, microwave, incinerate, paint, or insert foreign
objects into the LCD BacPac. Do not use the LCD BacPac
if it has been damaged—for example, if LCD BacPac is
cracked, punctured, or damaged by water.
The LCD screen is made of glass. This glass could break
if the BacPac is dropped on a hard surface without the
waterhousing or receives a substantial impact or is
crushed, bent, or deformed. If the glass chips or cracks,
do not touch or attempt to remove the broken glass.
Glass cracked due to misuse or abuse is not covered
under the warranty.
KEEPING THE LCD CLEAN
Clean LCD screen immediately if it comes into contact
with any contaminants that may cause stains, such as
ink, dyes, makeup, dirt, food, oils, and lotions. To clean
the LCD, use a so, slightly damp, lint-free cloth. Avoid
getting moisture in openings. Don’t use window cleaners,
household cleaners, aerosol sprays, solvents, alcohol,
ammonia, or abrasives to clean LCD BacPac.
9

AVOIDING WATER AND WET ENVIRONMENTS
WHEN NOT IN HOUSING
When not protected in the waterhousing, do not use the LCD
BacPac in rain, or near washbasins or other wet locations.
Take care not to spill any food or liquid on the LCD BacPac.
In case the LCD BacPac gets wet, turn o and unplug from
camera before cleaning, and allow it to dry thoroughly
before using again. Do not attempt to dry the LCD BacPac
with an external heat source, such as a microwave oven or
hair dryer. Damage to the LCD BacPac caused by contact
with liquid is not covered under the warranty.
USING CONNECTORS AND PORTS
Never force a connector into a port. Check for obstruc-
tions on the port. If the connector and port don’t join with
reasonable ease, they probably don’t match. Make sure
that the connector matches the port and that you have
positioned the connector correctly in relation to the port.
KEEPING THE LCD BACPAC WITHIN
ACCEPTABLE TEMPERATURES
The LCD BacPac is designed to be operated in tempera-
tures between 0° C and 40° C and stored in temperatures
between 0° C and 50° C. Low-or high-temperature condi-
tions might temporarily shorten battery life or cause the
LCD BacPac to temporarily stop working properly. Avoid
dramatic changes in temperature or humidity when using
the LCD BacPac as condensation may form on or within
the LCD BacPac. When you’re using the LCD BacPac
or charging the battery, it is normal for the LCD BacPac
to get warm. The exterior of the LCD BacPac functions
as a cooling surface that transfers heat from inside the
unit to the cooler air outside.
10

WARRANTY
This product is guaranteed against manufacturing defects
for one (1) year from the original date of purchase.
GoPro’s sole obligation in the event of such defects
during this period is to repair or replace the defective part
or product with a comparable part or product at GoPro’s
sole discretion. Except for such replacement, the sale,
or other handling of this product is without warranty,
condition or other liability even though the defect or loss
is caused by negligence or other fault. Damage resulting
from use, accident, or normal wear and tear is not covered
by this or any warranty. GoPro assumes no liability for any
accident, injury, death, loss, or other claim related to or re-
sulting from the use of this product. In no event shall GoPro
be liable for incidental or consequential damages relating to
or resulting from the use of this product or any of its parts.
Because of possible user resealing error, this product
is not warranted against waterhousing leakage or any
resulting damage. Visit gopro.com for more information.
11

Learn about more GoPro products
at: gopro.com
AM-WOO-LCD-0C Please Recycle