Gorilla Carts MH1370-01 User manual

REV 1/07
Heavy Duty Farm Cart
With Removable Folding Sides
Owners Manual
Model MH1370-01
For product inquiries:
Tricam Industries Asia Ltd.
7677 Equitable Drive
Eden Prairie, MN 55344
800-867-6763
www.tricam.com
• Important Safety Instructions
• Assembly Instructions
• Parts and Hardware Identification
CAUTION: Read, understand and follow ALL instructions before using this product.

IMPORTANT SAFETY INSTRUCTIONS
1. READ ALL INSTRUCTIONS CAREFULLY BEFORE USE. If you do not understand these instructions, need
clarification or further explanation, please call our toll free answer line for assistance at 1-800-867-6763
Monday through Friday 8:00 a.m. until 5:00 p.m. CST.
2. Do not load cart with more than 1,200 lbs. (544kg)
3. Do not allow children to use the cart unsupervised. This cart is not a toy.
4. Always distribute payload evenly over surface of cart.
5. If any parts become damaged, broken or misplaced, do not use the cart until
replacement parts can be obtained.
6. Do not operate or use on objects that can cause damage to the pneumatic tires or tubes.
Do not inflate tires more than 30 psi.
7. SAVE THESE INSTRUCTIONS.
ASSEMBLY INSTRUCTIONS
Your cart requires assembly. Account for all parts and hardware before beginning assembly. If any parts are missing,
damaged, or if you have questions or need additional instructions, DO NOT RETURN THIS
PRODUCT TO THE RETAILER, call the manufacturer at 1-800-867-6763
Tools required for assembly: Medium size slot screwdriver, 6, 8, and 12mm open end wrench and /or two medium
adjustable wrenches.
Refer to the exploded drawing and the parts list on the following pages during assembly.
SStteepp11
Assemble the Rear Axle Support to the Frame
Support using (4) 6x16mm frame support bolts and
6mm lock nuts. Tighten all bolts and lock nuts
securely.
SStteepp22The Front Axle Support is mostly pre-assembled
at the factory. Please make sure that all of the bolts and
lock nuts assembled at the factory are tight.
A. Insert the two remaining 8x15mm shoulder bolts into each
end of the Steering Link Connector. Apply 6mm washers and
6mm lock nuts and tighten securely.
B. Attach the Front Axle Support to the Frame Support using
(4) 6x16mm frame support bolts and 6mm lock nuts.
C. Secure the Center Front Axle Brace to the Frame Support
using (2) 8x20mm frame support bolts, 8mm washers and
lock nuts.

SStteepp33
Attach the Frame Support to the Bed using (4) 8x15mm
frame support bolts, 8mm washers, and lock nuts. Tighten
securely.
SStteepp44
Assemble the wheels using bushings (4pcs.), washers
(4pcs.), and locking nuts (4pcs.).
Tighten all nuts securely.
SStteepp55
Attach the Swivel Handle to the Yoke and the Plastic
Coupling using the 8x60mm bolt, 8mm washer and lock nut.
SStteepp66
The Lock Handles are pre-assembled onto the Panels at
the factory. NOTE: Do not tighten the lock nuts on the
Lock Handles until the end of this step.
Attach the Front, Back, and
(2) Side Panels onto the Bed using the Fence Assembly
Pins. Latch the Front and Back Panels to the Side Panels
using the Lock Handles. Once all panels are locked
together in the upright position, tighten the 8mm lock nuts
on the Lock Handles for smooth operation without being
overly tight.
SStteepp88
Install the Plastic Tray into the bottom of the Base.
Swivel Handle Instructions
Step 1
Remove clips and cotter pins.
Step 2
Rotate the handle and
insert cotter pin.
Secure by attaching the clip.
Step 3
The second cotter pin
is used to attach the
handle to the trailer hitch.

MAIN FRAME PARTS
1Bed - (1)
2Side Panels - (2)
3Front/Back Panels - (2)
SUPPORT ASSEMBLY
4Frame Support - (1)
513” Wheels - (4)
6Rear Axle Support - (1)
7Front Axle Support - (1)
8Center Front Axle Brace - (1)
9Yoke - (1)
10 Steering Link Connector - (1)
11 Plastic Coupling - (1)
12 Handle - (1)
ASSEMBLY HARDWARE
13 Fence Assembly Pins - (8)
14 Handle Pin - (2)
15 Clevis Pin - (2)
16 Washers 8mm - (11)
17 Lock Nuts 8mm - (11)
18 Wheel Spacer Bushings - (4)
19 Wheel Nuts 12mm - (4)
20 Wheel Washers 12mm - (4)
21 Frame Support Bolts 6 x 16mm - (8)
22 Pull Handle Bolt 8 x 60mm - (1)
23 Shoulder Bolts 8 x 15mm - (2)
24 Washers 6mm - (4)
25 Lock Nuts 6mm - (10)
26 Lock Handle 8mm - (4)
27 Frame Support Bolts 8 x 20mm - (2)
28 Frame Support Bolts 8 x 15mm - (4)
PARTS AND HARDWARE IDENTIFICATION
14
15
18 19
16 17
21
22
24
23
20
25
26
27
13
28

EXPLODED DRAWING FOR ASSEMBLY
6
5
8
10
7
9
12
1
11
2
3
4
Removable
Plastic Tray