Goscam GB8209 User manual

Contents
1. Packing List
2. Diagram
3. Structure
4. Installation
5. Specification
6. FCC and EU
1
1
2
3
8
9

1. Packing List
2. Diagram
Sensor for camera
* 8209AW means GB8209 + GB7609

3. Structure
3-1. Structure of Camera
3-2. Structure of Receiver
Antenna
Antenna
Speaker
IR LEDs
TFT-LCD
Power
On/Off
Alarm
Switch
Sensitivity
Switch
Channel
Switch
Battery
Cover
Battery
Cover
Lens
Power
Socket
Channel
Indicator
AV Out
Volume
Switch
Power
On/Off
Sleep
Button
Power
Socket
Sensor
Socket
Channel
Button
Eliminate
Alarm
Button

4. Installation
4-1. Installation of Camera
4-1-1. Basic installation of Camera
2. Connect thecamera to theadapter and thenslide the power
switch to ON position.
Note:
This camera canalso use drybattery as powersupply. Please load
4 AA batteriesto the batterycompartment at theback of camera
with their polaritiesmatched.
The AC adapterwill work insteadof batteries afterit is plugged.
If the camerais not usedfor a longperiod of time,please unplug
the adapter andremove the batteries.
Avoid short circuit of the battery.
* Continue working for 5 hours(IR OFF)

3. Rotate the rounded headof camera toa suitable anglefor
surveillance.
1. Check out theright side of thecamera and there is the channel
switch marked as CH1,CH2, CH3, CH4. Eachof them can be
selected separately for the purposeof the multi-camera working
situation or interference avoidance.
2. Press channel buttonof the receiver toselect the same channel as
the camera, The pictures willbe displayed on thescreen.
30
30
4-1-2. Camera channel setup
4-1-3. Camera alarm setup
CH4 CH3 CH2 CH1
Off Motion Sensor Sound
Low Middle High
Ch1: 2,414MHz
Ch2: 2,432MHz
Ch3: 2,450MHz
Ch4: 2,468MHz
1. The cameraprovides Motion Detection,Sensor Detection, Sound
Detection. Each modecan separately beselected by 3sensitivity levels
as Low, Middle, High.
Alarm
Sensitivity

2. Connect thesensor jack tothe camera sensorsocket, put thesensor
end in cottondiaper if youselect the Bed-wettingSensor detection.
* Specialists recommend the sensor is not suitable
for disposable panty diaper; and not suitable for
touching skin directly.
Motion Alarm Setup:
It refers tothe alarm against various movements. If youslide the
alarm setting switch to Motionposition, and select Sensitivity
switch. Afterward, the system enters the motionalarm mode. When
a movement isactually detected, thealarm begins untilyou press
the Eliminate AlarmButton. After less than 1minute, the motion
alarm enters thenext alarm circle.
Sound Alarm Setup:
It refers tothe alarm againstsound . Ifyou slide thealarm setting
switch to Soundposition, and select Sensitivity switch. Afterward,
the system entersthe sound alarmmode. When thesound is actually
detected, the alarmbegins until youpress the EliminateAlarm Button.
After less than 1 minute,the sound alarmenters the nextalarm circle.
Sensor Alarm Setup:
It refers tothe alarm againstbedwetting. If youslide the alarm
setting switch toSensor position, and select Sensitivity switch.
Connect the sensorto camera anddiaper.Afterward, the system enters
the sensor alarmmode. When thebedwetting and wateris actually
detected, the alarmbegins until youpress the EliminateAlarm Button.
After less than 1 minute,the motion alarm enters thenext alarm circle.
Off Alarm Setup:
It refers tothe abandonment of the alarmfunction. If youslide the
alarm setting switch to Offposition. The alarm function isdisabled.
Note:
When the camerais powered onby dry batteriesand directly plugged
in by theadapter,the alarm functionfails to work.If this isthe case,
please slide thepower Off andback again toOn, the alarmfunction
is successfully activated.

4-2. Installation of Receiver
4-2-1. Basic installation of Receiver
1. Connect thereceiver to theadapter and thenslide the power
switch to ONposition.
2. Adjust thevolume control toa desired level.
Note:
This receiver canalso work ondry battery. Please load4 AA
batteries to thebattery compartment atthe back ofreceiver with
their polarities matched.
The AC adapterwill work insteadof batteries afterit is plugged.
If the receiveris left unusedfor a longperiod of time,please unplug
the adapter andremove the batteries.
Avoid short circuit of the battery.
* Continue working for 5 hours

3. Set thechannel of receiverto be thesame as cameraby pressing the
channel button continuously, and thepictures will displayon the
screen.
Note:
For moreclear pictures, pleaseconnect the receiverto a monitor/TV
with AVcable (yellow forvideo and redfor audio).
AV cable
1. Volume adjustment
Slide Volume Switch to adjust thevolume of thereceiver.
2. Channel selection
Press CH button to select theappropriate channel.
3. Channel Looping
Hold the CH button for three secondsto enter theloop mode. All
the available channelswill be displayedone by one(default
interval is 5seconds).
4. Sleep Mode
Press the Sleep Button to shut downthe LCD displayand keep
the voice function.Press the buttonagain and recallthe normal
working mode. Itcan save energyand help yoursleeping.
5. Eliminate Alarm button
Press Eliminate Alarm button to eliminatealarm voice .Less
than 1 minute,the alarm entersagain next circleautomatically.
4-2-2. Operation of Receiver

5. Specification
CAMERA
RECEIVER GENERAL
Item Value
Transmission Frequency
Transmission Power
Operating Frequency
Unobstructed Effective Range
Modulation Mode
Operating Temperature
Operating Humidity
Imaging Sensor Type
Picture Total Pixels
Minimum Illumination
Night Vision Distance
Bandwidth
Battery WorkingTime
Motion Alarm Distance
Sound Detection Sensitivity
Consumption Current(Max.)
Power Supply
Dimensions(W D H)
Weight(About)
LCD Screen Type
Effective Pixels
Receiving Sensitivity
Consumption Current(Max.)
Battery WorkingTime
Power Supply
Dimensions(W D H)
Weight(About)
ISM 2,400~2,483 MHz
10mW/CE; 2mW/FCC
2,414MHz; 2,432MHz;
2,450MHz; 2,468MHz
100m(Min.)
FM
-10 ~ +50 / +14 ~ +122
85%
CMOS
PAL: 720 480Pixels;
NTSC: 724 576Pixels
0Lux (IR ON)
5m
18M
5 hours (IROff)
5m
>63dB
DC+8V/500mA
86 48 135mm
146g
2.4 TFT-LCD
480 240
-85dBm
200mA
5 hours
DC+8V/500mA
86 54 143mm
142 g
120mA(IR OFF) &220mW(IR ON)

6. FCC information
This device complies with part15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference,
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user s authority to operate the
equipment.

Warning:
Changes or modifications to this unit not expressly approved by the
party responsible for compliance will void the user’s authority to
operate the equipment. Any change to the equipment will void FCC grant.
This equipment has been tested and found to comply with the limits
for a Class B digital device,pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
The equipment compliance with FCC radiation exposure limit set forth for
uncontrolled Environment