Gossen MetraWatt METRACLIP 62 User manual

Operating Instructions
METRACLIP62
Clip-On Ammeter
3-349-391-15
2/3.10
www. .com [e-mail]1.800.561.8187

2 GMC-I Messtechnik GmbH
Operating Overview
1
2
15
4
5
6
7
8
9
3
14
13
12
11
10
U: < 300 V !
I: max. 10 A !
www. .com [e-mail]1.800.561.8187

GMC-I Messtechnik GmbH 3
1 Clip guide (+ shield)
2 Clip jaw
3 Clip clearance safety barrier:
Do not reach beyond the safety collar!
4 Button for opening clip
5 MAX HOLD key: display max. current measured value
6
MIN HOLD key: display min. current measured value
7RANGE UP key: increase measuring range
8POWER key: switch on instrument (LCD test)
/ switch off instrument
9 LCD panel
10 Eyelet for carrying strap
11 ACA key: activate AC measurement
12 DCA key: activate DC measurement
13 RANGE DOWN key: reduce measuring range
14 DATA HOLD key: save measured value
by „freezing“ display
15
ZERO ADJ key: DCA: zero balancing
(activate before each DC measurement
!)
ACA: define reference value
Standard Equipment
1 Clip-on ammeter
1 Immitation leather bag
1 Set of batteries
1 Operating instructions
www. .com [e-mail]1.800.561.8187

4 GMC-I Messtechnik GmbH
Table of Contents Page
1 Safety Precautions ..............................4
1.1 Special Features of the Hall Effect Sensor ........ 6
2 Operation .............................................7
2.1 Initial Start-Up ............................................... 7
2.2 Stipulations for All Measurements ................... 8
2.3 Measuring Leakage Current at Grounded
Conductors .................................................. 10
2.4 Measuring Leakage Current at
Single-Phase or 3-Phase Systems ................ 11
2.5 Measuring Line Current ................................ 12
3 Characteristic Values .........................13
4 Maintenance ......................................16
4.1 Battery Replacement .................................... 16
4.2 Housing ...................................................... 17
1 Safety Precautions
The METRACLIP62 clip-on ammeter has been
manufactured and tested in accordance with
safety regulations IEC 61010-1/EN 61010-1/
VDE 0411-1 and IEC 61010-2-032/
EN 61010-2-032/VDE 0411-2-032.
If used for its intended purpose, the safety of
the user and of the device is assured. The
device may only be operated by properly
trained personnel who are capable of recog-
www. .com [e-mail]1.800.561.8187

GMC-I Messtechnik GmbH 5
nizing the dangers associated with the mea-
surement of electrical current and voltage.
Read the operating instructions completely and
carefully before using the device, and follow all
instructions included therein.
Meanings of symbols on the instrument:
Warning concerning a source of dan ger
(Attention: observe documentation!)
Continuous, doubled or reinforced
insulation
Indicates EC conformity
Applying the clip to dangerous active
conductors is permitted
The clip-on ammeter may not be used:
• If the battery compartment lid has been
removed
• If visible damage is apparent
• With damaged connector cables
• If it no longer functions flawlessly
• After lengthy periods of storage under
unfavorable conditions (e.g. humidity,
dust, temperature).
!
www. .com [e-mail]1.800.561.8187

6 GMC-I Messtechnik GmbH
Attention!
!
Do not perform measurements in the
event of over-ranging!
Current which exceeds the measuring
range may not be measured.
Do not perform measurements at bare
wires!
Do not perform measurements at busbars!
Safe Handling
• The housing and the handles must be free
of dust, grease and moisture.
• The operator’s fingers may not be
extended beyond the safety collar during
measurement.
• Avoid excessive mechanical stress such
as impact and vibration, as well as high
temperatures, moisture and strong
magnetic fields.
• The battery compartment lid must be
secured with the appropriate Phillips head
screw.
1.1 Special Features of the Hall Effect Sensor
Eliminating the influence of magnetization
The clip-on ammeter METRACLIP62 uses the
hall effect for its measurements. The charac-
teristics of the hall effect are subject to a hys-
www. .com [e-mail]1.800.561.8187

GMC-I Messtechnik GmbH 7
teresis due to magnetization. As a result, the
zero adjustment point for DC measurements
may vary. Open and close the clip jaws several
times in a row and press the ZERO ADJ key prior
to each DC measurement in order to elimitate
this effect. When measuring current conduct-
ing cables, close and open the clip jaws slowly
and firmly in order to avoid any impact on the
sensitive hall effect sensor.
Remedy in the Event of Exceeding the Measuring
Range
If the maximum measurable current has been
exceeded by a large degree, zero balancing
can no longer be effected due to the satura-
tion of the current clip.
Remedy:
➭Turn the measuring instrument on with the
POWER key.
➭Adjust the smallest measuring range with
the RANGE DOWN key (200 mA AC).
➭Close the clip around a conductor with
10 A AC and reduce the current in the
conductor gradually to 0 A. This elimi-
nates magnetic saturation.
2Operation
2.1 Initial Start-Up
Insert the two batteries (see chapter 4.1, page
16.
www. .com [e-mail]1.800.561.8187

8 GMC-I Messtechnik GmbH
2.2 Stipulations for All Measurements
Attention!
!
In order to prevent damage to the in-
strument and the user, the maximum
input quantities may not be exceeded:
Voltage range 300 V AC/DC,
current range 20 A AC/DC.
Note

Exercise caution when opening and closing
the clip jaws around an active conductor.
Save Measured Value Function – DATA HOLD
During the performance of measurements
under conditions which impair easy reading of
display values, the DATA HOLD key can be
activated in order to freeze the momentary
measured value at the display. The DH symbol
appears at the display.
Before starting any new measurements, the
DATA HOLD key must be activated once again in
order to reset the data hold function.
Display of Extreme Value Function – MAX HOLD / MIN HOLD
In order to indicate the highest (MAX HOLD) or
lowest current measured value (MIN HOLD) dur-
ing a measurement, briefly press the corre-
sponding key before starting the measure-
ment; the symbol MAX-H or MIN-H appears.
During this function, the automatic shutdown
www. .com [e-mail]1.800.561.8187

GMC-I Messtechnik GmbH 9
mode is deactivated. Press the key again to
cancel this function.
Selecting Current Type – ACA / DCA
The measuring instrument is always set to
direct current when switched on. Press the
ACA or DCA key to change to the other current
type.
Zero Balancing or Reference Value Function
– ZERO ADJUST
Zero Balancing for DC measurements DCA
Even if the clip jaws are not closed around a
conductor, measured values are continuously
displayed when the measuring instrument is
set to DC measurement. It is therefore gener-
ally necessary to press the ZERO ADJUST key
after selecting the measuring range and before
starting DC measurements. After pressing the
ZERO ADJ key, the symbol ZERO ADJ is displayed
and 0.0, 0or 0.00 appears on the LCD.
After changing the measuring range or the
current type, the function must be reactivated.
Reference Value for AC measurements ACA
If the ZERO ADJUST key is pressed during an AC
measurement, the measured value is stored
as a reference value and deducted from future
measurements. After pressing the ZERO ADJ.
key, the symbol ZERO ADJ is displayed and
0.0, 0or 0.00 appears on the LCD.
www. .com [e-mail]1.800.561.8187

10 GMC-I Messtechnik GmbH
2.3 Measuring Leakage Current at Grounded
Conductors
➭Turn the measuring instrument on with the
POWER key.
➭Select the current type via the ACA or DCA
key.
➭Set the RANGE UP or RANGE DOWN key to the
appropriate range for the current to be
measured.
Otherwise, set the measuring range
switch to the highest of the three ranges in
order to avoid possible over-ranging.
➭Prior to DC measurements:
Perform zero balancing via the ZERO AD-
JUST key.
➭Close the clip around the current conduct-
ing cable under test as well as around the
current transformer.
➭Read the measured value from the dis-
play.
➭After measurement has been completed:
Remove the clip from the cable and turn
the measuring instrument off by pressing
the POWER key.
www. .com [e-mail]1.800.561.8187