GPM VENETIA SHOVENSON User manual

GOLBAL PROCUREMENT AND MARKETING LIMITED
HOME VENETIA SHOE CABINET
Assembly instruction- Please keep for future reference
Dimensions No.People Assembly Time OW#
Width: 60 cm
Depth: 32 cm
Height: 86.5 cm
45 mins
(approx)
Important-Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
thank you
For purchasing this
GPM Limited
product
1
SHOVENSON SHOVENGRY
SHOVENSON
SHOVENGRY
810mm
600mm
320mm
130mm
55mm

Safety and Care Advice
!
Important-Please read these instructions fully before starting assembly
If you are unhappy with the product and wish to return it,
please following the retailer’s returns procedure.
Components - Panels
Make sure you have enough
space to lay out the parts
before starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close to
its final position (in the same
room) as possible.
Assemble on a soft, level
surface to avoid damaging the
unit or your floor.
We do not recommend the
use of power
drill/drivers for
inserting screw,
as this could
damage the unit.
only use hand screwdrivers.
Dispose of all packaging
carefully and responsibly.
Care and Maintenance
This product should not be
discarded with household
waste.Take to your local
authority waste disposal centre.
From time to time check
that there are no loose
screws on this unit.
Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
Check you have all the
components and tools listed
on pages 2,3 and 4.
Remove all fittings from the
plastic bags and separate
them into their groups.
Keep children and animals
away from the work area,
small parts could choke if
swallowed.
2
1
2
3
4
5
76
15
14
13
13
12
8
9
10 11

Components - Panels
Please check that you have all the components listed below before constructing your item.
Important-Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
If you have damaged or missing components,
email: [e-mail]
Part No Description Qty Thickness
(mm)
1
2
3
4
5
6
7
8
9
10
Right Side Panel
Bottom Panel
Top Panel
15 mm
15 mm
15 mm
15 mm
15 mm
3 mm
15 mm
15 mm
1
1
1
1
1
1
1
1
1
3
Back Panel
Left Side panel
15 mm
Drawer Front Panel
Drawer Side Panel
Drawer Back Panel
Drawer Base Panel
11
1
Centre Front Panel
Back Panel
3 mm
Shelf Panel
Shelf Panel
Left Door panel
Right Door Panel 15 mm
15 mm
15 mm
1
12
13
14
15 3 mm
1
15 mm
2
1
1

Components - Fixings
Please check that you have all the components listed below before constructing your item.
Important-Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, please email [e-mail]
If you have damaged or missing components,
email: [e-mail]
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
0
mm
10
515 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180
Ruler - Use this to measure your screws (mm)
Tools Required ( Not Provided)
(A) (B) (D)( C )
(L) (M)
(O)( N ) (P)
4
HARDWARE
ANTI - TIPPING KITS
M3.5 X 20mm X 2 Wall Plug X 2 Strap X 1
Bracket X 2
M4 X 32mm X 2
(E)
(F) (G) (I)( H ) (J)
(K)
JCBC M5 X 40mm X 6 M4 X 32mm X 10 M3.5 X 14mm X 46
Dowel (M8X25) X 6
Nail X 32
Plastic Shelf Support X 8
Mini Fit X 2 set
Drawer Slide 12” X 1 set Allen Key X 1
Bolt Nut
(Q) ®
Handle X 3 Plastic Leg X 4 L- Bracket X 2
Hinges X 4

D
F
13 x2
D
D
12
FRONT
RIGHT
3
L
CCC
FRONT
LEFT
1
L
CCC
Attach drawer slide rail to Panel boards & with screw onto the specific pre-drilled pilot holes as shown below.
L
13
C
Assembly Instructions If you have damaged or missing components,
email: [e-mail]
Step 2
Step 1
5
3
F
G
G
1
F
G
G
2a. Attach Dowel to Panel , &
F1313
2b. Attach Minifit bolt to Drawer front panel & Minifit Nut to
D12 D
Drawer Side panel .
13
of Panel & .
2c. Attach Shelf support stud onto the predrilled holes
G
13

A
A
A
A
1
2
3
4
5
C
J
5b. Attach Top panel using
L-Bracket with Screw
5
JC
5a. Attach Panel , , , & with
Screw using Allen key to tighten.
12345
A
1 st 2nd
INSERT
RIGHT
POISITION
3rd
LOCK
H
B
DB
B
12
13
13
14
15
E
3b. Fasten drawer side panel to front panel to minifit
using Screw driver to lock. Secure the drawer back panel
with screw using a screw driver to tighten.
13 1 2 D
14
B
3c. Attach base board with Nail to the
drawer base using a small hammer.
15 E
3a. Attach Handle to drawer Front panel with Screw and tighten with Screw driver.
H12 B
Step 3
Step 4
Step 5
6
L
L
C
C
CL
C
C
Attach drawer slide rail to drawer base
with screw and tighten with screw driver.
L
C

2nd
P
1st
WALL
Drill
Bit
6mm
N
Q
Install Door hinger
with Screw using
Screw driver to tighten.
K
C
C
K
10
14
11
8
9
Lay on Shelf panel & as shown
89
6c. Attach Leg with screw as shown.
IC
6a. Attach back board & to the back of cabinet,
with Nail using a small hammer.
67
E
Step 6
Step 7
Step 9
7
6b. Attach Anti tipping kit bracket
with Screw
Q
O
I
C
E
6
7
Q
O
Slide assembled Drawer unit into place.
Step 8
4th Q
Q
R
Attach the Anti-tipping kit onto wall
following the steps as shown.
COMPLETE