Note: in order to use a DMX
ontroller you must make sure the
ba k panel is in DMX mode. To do
this press “MENU” until the LED
s reen reads [A001], and the press
“ENTER” to onfirm.
Channel Fun tion
CH1 Dim
CH2 Red
CH3 Green
CH4 Blue
CH5 Strobe
CH6 Preset
CH7 Speed
I.Operation
This light has 4 fun tions:
1. DMX512 with 7 hannels
2. Automati operation
3. Sound A tivated
4. Master/slave
III. DMX Channel List
(For use with ontroller) IV. Spe ifi ations
II. Menu:
Menu Panel
(lo ated on ba k)
●DMX512 with 7 hannels,
Automati operations, Sound
a tivated, and Master/slave
●Super bright 3W LED Lamp
12 Red, 12 Green, 12 Blue.
●Color temperature less than
6000K
●0 – 100% light dimmer
●Multi-flash effe t 1 – 10 time
per se open/ lose
●Low power onsumption. Est.
100,000 hour life span
●Voltage: AC90V-240V/50 or
60Hz
●Power: 120W
1. [A001]: This is the DMX Function of this fixture. You can press “UP or “DOWN to set it
from [A000] up to [A512], and then press “ENTER to confirm it. This function allows you to
put the light fixture in DMX mode so that you may use a controller if needed.
2. [ADYE]: Is the DMX come back mode. You can press “UP or “Down to set it from
[ADNO] to [ADYE] to choose if the light can come back to DMX mode automatically when
there is DMX signal or not. Press “ENTER to confirm it. This is the power setting save
feature. This will allow your settings to come back to how you left them if you lose power.
3. [AU01]: These are the preset colors. You can press “UP or “DOWN to set it from
[AU01] up to [AU07], then press “ENTER to confirm it. Each number is a different preset
color you can use.
4. [FFxx]: Is the color alternating feature. You can press “UP or “DOWN to set the speeds
from [FF00] up to [FF99], then press “ENTER to confirm it. This feature automatically
cycles the light through different colors.
5. [EExx]: Is the color cross fade in/fade out. You can press “UP or “DOWN to set the
speed from [EE00] up to [EE99], then press “ENTER to confirm it. In this setting the light
will cycle through preset colors with a fade effect. The fade will blend with the previous
color before fully changing.
6. [CCxx]: Is the color fade in/fade out. You can press “UP or “DOWN to set the speed
from [CC00] up to [CC99], then press enter to confirm. In this feature the colors will
automatically cycle but the color will fade completely out before allowing the new color to
fade in.
7. [Fxxx]: Is the strobe effect. You can press “UP or “DOWN to set the speed from [F000]
to [F255] and then press “ENTER to confirm. This allows you to change the speed at which
the light blinks. Use the color mixing listed below to choose what color you would like to
have strobe.
8. [SOUD]: Is the sound activated strobe effect. You can press “UP or “DOWN to set it
from [SOUD] to [SOND] to choose the sound activated strobe effect. This effect will make
the light blink when a noise is picked up by the internal microphone in this fixture.
9. [SOND]: Is the sound activated automatic operation effect. This features will change the
light in it's cycle every time the internal microphone in this fixture picks up a noise.
10. [Rxxx]: Is the red color dim. You can press “UP or “DOWN to set it from [R000] up to
[R255] to dim the red color, then press “ENTER to confirm it.
11. [Gxxx]: Is the green color dim. You can press “UP or “DOWN to set it from [G000] up
to [G255] to dim the green color, then press “ENTER to confirm it.
12. [Bxxx]: Is the blue color dim. You can press “UP or “DOWN to set it from [B000] up to
[B255] to dim the blue color, then press “ENTER to confirm it.
.
(For use without controller)
