Graco Pulse 25P363 User manual

3A6943A
EN
Instructions
Pulse™ Remote
Extender
For use with Pulse Fluid Management System Components only. The Pulse Extender
creates a supplementary Pulse Device Network. It connects to the Pulse HUB over the
facilities LAN.
Not approved for use in European explosive atmosphere locations.
For Indoor use only.
Part 25P363
.
Important Safety Instructions
Read all warnings and instructions in this
manual before using the equipment.
Save these instructions.

Pulse Remote Extender Overview
23A6943A
Pulse Remote Extender Overview
Component Identification
The Pulse Remote Extender manages remotely
deployed Pulse components. The components reside on
a Personal Area Network (PAN) hosted by the Pulse
Remote Extender. The Pulse Remote Extender sends
component information to the Pulse HUB using a user
supplied Local Area Network (LAN) connection (FIG. 1).
1 Button: Not used.
2 LED Status Lights
Power: indicates power is on when lit
Xbee: indicates hardware/configuration is active when lit
Network: indicates network is active when lit
3 Power Inlet Port (5VDC)
4 Ethernet (Network) Connection
FIG. 1: Pulse Remote Extender Components
1
4
3
2

Installation
3A6943A 3
Installation
Place the Pulse Remote Extender in the main part of the
facility, located either high on a wall or on the ceiling.
Install the Pulse Remote Extender on an unobstructed
line of sight of any Meters, Pump Air Controls or Tank
Level Monitors (FIG. 2).
Installation should comply with all applicable local, state
and national fire, electrical and safety codes and
regulations.
FIG. 2: Example of Facility Layout

Operation
43A6943A
Operation
The Remote Extender is configured for Dynamic Host
Configuration Protocol (DHCP). On most networks, the
Remote Extender automatically connects to the local
network. It is recommended that the facility’s IT depart-
ment be contacted to provide the Remote Extender a
reserved IP address located on the same sub-network
as the Pulse HUB.
Remote Extender Discovery
1. Pulse HUB is stable on the local network at a fixed
IP address.
2. Connect the Ethernet to the Remote Extender
(FIG. 3).
3. Connect the power adapter to the Inlet Port. The
other end of the power adapter is plugged into a
120-240VAC electrical outlet.
4. Place Pulse HUB into Discovery Mode to begin the
process of connecting the Remote Extender to the
Pulse HUB.
NOTE: If the Remote Extender is in the initial listening
state, this should only take a few seconds.
5. After the Remote Extender is found, exit Discovery
Mode on the Pulse HUB.
Device Discovery
1. From the Pulse software, navigate to the Device
Network Screen.
2. There are multiple sections listed under the Device
Network header, one for the HUB and others for the
Remote Extenders.
3. Toggle on Discovery Mode under the Remote
Extender section.
4. Register devices with the Remote Extender
following the instructions for your devices, similar to
the device registration process for the HUB.
FIG. 3: Connecting Ethernet

Troubleshooting
3A6943A 5
Troubleshooting
Problem Cause Solution
Power LED is not lit Not being powered Verify the power supply is connected
to a power source.
Verify that the device is connected to
a power source.
Hardware Failure Disconnect power and reconnect. If
problem persists, replace hardware.
XBee LED is not lit Hardware/Configuration Failure Disconnect power and reconnect. If
problem persists after 60 sec.,
replace the hardware.
Network LED is not lit Hardware/Configuration Failure Disconnect power and reconnect. If
problem persists after 60 sec.,
replace the hardware.
Network LED flashing yellow, slower
than once per second
No Ethernet connection. Disconnect Ethernet cable and
reconnect. If that does not solve the
issue, replace the Ethernet cable.
Network LED is flashing yellow,
faster than twice per second
DHCP server is not responding.
The device may not be connected to
the DHCP server, even if there is a
link to a hub or switch.
Check with network administrator.

Technical Specifications
63A6943A
Technical Specifications
Pulse Extender
US Metric
Dimensions 3.0 x 3.0 x 3.0 in. 7.62 x 7.62 x 7.62 cm
Weight 0.15 lb 0.07 kg
Operating Voltage 5VDC
Power Consumption Typical: 1.2 W, Max: 2.5 W
Operating Temperature 32° F to 104° F 0° C to 40° C
Relative Humidity 5% to 95% (non-condensing)
RF Frequency Band 2.4 GHz (ISM)
Maximum Transmit Power 6.3 mW (+8dBm)
RF Range 200 ft. 60 m

Graco Standard Warranty
3A6943A 7
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.

All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A6943
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2019, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision A, June 2019
Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: [phone] or Toll Free: 1-800-533-9655, Fax: [phone]