Graco XD30 Series User manual

Instructions
XD30 Series High
Capacity Hose
Reels 3A0138J
EN
Used in applications requiring long range dispense, transfer or evacuation of fuels, air,
water, lubricants and other automotive fluids such as oil, grease and transmission fluids.
For professional use only.
Not for use in explosive atmospheres.
Application markets include: mobile equipment servic-
ing, heavy construction and industrial plants.
HS Models: Page 3
HN Models: Page 4
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
ti13980
HN Models HS Models

Warnings
23A0138J
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back
to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where
applicable.
WARNING
FIRE AND EXPLOSION HAZARD
When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be
aware that flammable fumes can ignite or explode. To help prevent fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources, such as cigarettes and portable electric lamps.
• Keep work area free of debris, including rags and spilled or open containers of solvent and gaso-
line.
• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
• Ground all equipment in the work area.
• Use only grounded hoses.
• If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
SKIN INJECTION HAZARD
High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This
may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical
treatment.
• Do not point dispensing device at anyone or at any part of the body.
• Do not put your hand over the fluid outlet.
• Do not stop or deflect leaks with your hand, body, glove, or rag.
• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking,
or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses and couplings daily. Replace worn or damaged parts immediately.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS from distributor or retailer.
• Do not leave the work area while equipment is energized or under pressure. Turn off all equipment
and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine man-
ufacturer’s replacement parts only.
• Do not alter or modify equipment.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.

Warnings
3A0138J 3
HS Models
Each model shown in the table below is available in several colors. The last character of each model no. indicates the
hose reel color. A = white + NPT, B = Metallic Blue + NPT, F = Yellow + NPT, and G = Desert Sand + NPT, P = white
+ BSPT, R = Metallic Blue + BSPT, U = Yellow + BSPT. On the table below, this last character is represented by the
generic # symbol. For example, to show the complete model number for a white HSHC5 model hose reel, the symbol
# is replaced with “A”. The complete model number is: HSHC5A.
NOTE: Truck mounted hose reels may require the hose/dispense valve be walked back into the hose reel for full
retraction.
MOVING PARTS HAZARD
Moving parts can pinch, cut or amputate fingers and other body parts.
• Keep clear of moving parts.
• Do not operate equipment with protective guards or covers removed.
• Pressurized equipment can start without warning. Before checking, moving, or servicing equip-
ment, follow the Pressure Relief Procedure and disconnect all power sources.
WARNING
Model No. Series Application Recommended
Mounting Position Hose Size Maximum Pressure
PSI Bar Mpa
HSHC5# A Grease Truck 1/2 inch 5000 345 34.5
HSHC5# B Grease Truck and Overhead 1/2 inch 5000 345 34.5
HSHFF# A & B Bare: Pressure Washer Truck and Overhead NA 5000 345 34.5
HSLC8# A & B Air/Water Truck and Overhead 1/2 inch 300 20.7 2.07
HSLD5# A & B Air/Water Truck and Overhead 3/4 inch 300 20.7 2.07
HSLE3# A & B Fuel/ Evacuation Truck and Overhead 1 inch 125 8.6 .86
HSMC8# A Oil Truck 1/2 inch 1500 103.4 10.34
HSMC8# B Oil Truck and Overhead 1/2 inch 1500 103.4 10.34
HSMD5# A Oil Truck 3/4 inch 1250 86 8.6
HSMD5# B Oil Truck and Overhead 3/4 inch 1250 86 8.6
HSMDD# A Bare: MP- LP 3/4” Truck NA 2000 138 13.8
HSMDD# B Bare: MP- LP 3/4” Truck and Overhead NA 2000 138 13.8
HSPB8# A & B Pressure Washer Truck and Overhead 3/8 inch 4000 275 27.5
HSHCD# A Bare: HP 1/2” Truck NA 5000 345 34.5
HSHCD# B Bare: HP 1/2” Truck and Overhead NA 5000 345 34.5
HSMCF# A & B Bare: LP 1/2” Truck and Overhead NA 2000 138 13.8
HSHB7# A Grease Truck and Overhead 3/8 inch 5000 345 34.5
HSPC5# A Pressure Washer Truck and Overhead 1/2 inch 4500 310.3 31.0

Warnings
43A0138J
HN Models
Each model shown in the table below is available in several colors. The last character of each model no. indicates the
hose reel color. A = white, B = Metallic Blue, F = Yellow, and G = Desert Sand. On the table below, this last character
is represented by the generic # symbol. For example, to show the complete model number for a white HNHC5 model
hose reel, the symbol # is replaced with “A”. The complete model number is: HNHC5A.
Model No. Application Hose
Size Maximum Pressure
PSI Bar Mpa
HNHC5# Grease 1/2 inch 5000 345 34.5
HNHFF# Bare: Pressure Washer NA 5000 345 34.5
HNLC8# Air/Water 1/2 inch 300 20.7 2.07
HNLD5# Air/Water 3/4 inch 300 20.7 2.07
HNLE3# Fuel/Evacuation 1 inch 125 8.6 0.86
HNMC8# Oil 1/2 inch 1500 103.4 10.34
HNMD5# Oil 3/4 inch 1250 86 8.6
HNMDD# Bare: MP- LP 3/4” NA 2000 138 13.8
HNPB8# Pressure Washer 3/8 inch 4000 275 27.5
HNHCD# Bare: HP 1/2” NA 5000 345 34.5
HNHB7# Grease 3/8 inch 5000 345 34.5
HNPC5# Pressure Washer 1/2 inch 4500 310.3 31.0
.

Installation
3A0138J 5
Installation
Typical Installation Layout
A Main air supply
B Pump air supply
CAirfilter
D Air regulator
E Bleed-type master air valve (user supplied, required)
FPump
G Grounding wire (user supplied, required for pump and
hose reel)
H Thermal relief valve (user supplied, required)
J Fluid drain valve (user supplied, required)
K Fluid shut-off valve
L Fluid line
M Hose reel
N Dispensing valve
P Flexible inlet hose
A ground wire (G), bleed-type master air valve (E), thermal relief valve (H) and fluid drain
valve (J) are required in your system installation. These (user supplied) components help reduce
the risk of serious injury.
•Theground wire (G) must be connected to the pump grounding lug and to a true earth
ground to prevent static sparking that could result when fluid is dispensed through the hose.
See your local code for specific requirements.
• The hose reel must be grounded.
•Thebleed-type master air valve (E) relieves air trapped between this valve and the pump
after the air is shut off. Trapped air can cause the pump to cycle unexpectedly, therefore
locate the valve close to the pump.
•Thethermal relief valve (H) and fluid drain valve (J) assist in relieving fluid pressure in the
displacement pump, hose and dispense valve. Triggering the dispensing valve (N) to relieve
pressure may not be sufficient. Open the fluid drain valve (J) to relieve fluid pressure that
may be captured elsewhere in the system.
FIG. 1
B
A
C
DE
F
G
J
H
ti13981
P
K
K
L
N
M
G

Installation
63A0138J
Pressure Relief Procedure
1. 2.

Installation
3A0138J 7
All Mountings
NOTE: Reels perform best when arm allows hose to pull
straight off the spool as shown in FIG. 2 and FIG. 3.
To reduce the risk of injury, be sure the mounting sur-
face and mounting screws are strong enough to sup-
port the reels, weight of the fluids and stress caused
by hard pulls on the service hoses. See Technical
Data, page 23 for weights of hose reel assemblies.
FIG. 2
FIG. 3

Installation
83A0138J
Wall Mounting
Ceiling Mounting
1. A = Screws 2. A = Screws
A
ti13982
A
ti13983
Maximum distance to
floor - 16 ft (4.87 m)
1. A = Screws 2. A = Screws
A
A
Maximum distance to
floor - 16 ft (4.87 m)

Installation
3A0138J 9
Truck Bed Mounting
Changing Position of Guide Arms (30)
HS Models Only
1. A = Screws
A
1. Remove nuts (33). Reposition guide arms (30) to
new location. 2. Reinstall nuts (33). Torque to 25 - 35 ft lbs (33.9 to
47.5 N·m).
33
30
33
30

Installation
10 3A0138J
Changing Hose Guide (31) Position
HS Models Only.
1. Remove screws (52) and nuts (53) (not shown).
Reposition hose guide (31) to new location. 2. Reinstall screws (52) and nuts (53) (not shown).
Torque to 25 - 35 ft lbs (33.9 to 47.5 N·m).
52
31
52
52 31
52

Installation
3A0138J 11
Flushing
Before installing meter or dispense valve to end of hose, flush supply line with a solvent compatible with the fluid you
are dispensing.
1. Place end of hose in waste container. 2. Blow out entire lubricant supply line with air.
3. Flush equipment with a compatible solvent until fluid
runs clear. 4. Pump dispensing lubricant through line until all sol- vent is flushed out.

Adjusting Spring Tension
12 3A0138J
Adjusting Spring Tension
Increasing Spring Tension
The spring is always under great tension, which if
released in an uncontrolled manner could cause seri-
ous injury.
• Never allow the reel to spin freely. Uncontrolled
spinning could cause serious injury if you are hit by
the hose.
• Always grasp the tool firmly with both hands when
adjusting tension. Spring tension can cause the
tool to move violently.
• The reel must be bolted securely in place when
making adjustments.
1. Loosen (A) 3-5 turns. Do not remove (A)! 2. Loosen (B) 3-5 turns. Do not remove (B) yet.
A
B

Adjusting Spring Tension
3A0138J 13
3. Insert tool (C) in opening. Hold tool (C) firmly to
engage spring force before removing screws (B). 4. Turn tool (C) one full turn clockwise.
5. Replace one screw (B). Leave tool (C) in place. 6. Remove tool (C).
7. Pull hose to test tension. Repeat 3 - 7 if necessary. 8. Replace and tighten screws (B) and (A).
if
B
C
B
C
B
C
B
BA

Adjusting Spring Tension
14 3A0138J
Decreasing Spring Tension
The spring is always under great tension, which if
released in an uncontrolled manner could cause seri-
ous injury.
• Never allow the reel to spin freely. Uncontrolled
spinning could cause serious injury if you are hit by
the hose.
• Always grasp the tool firmly with both hands when
adjusting tension. Spring tension can cause the
tool to move violently.
• The reel must be bolted securely in place when
making adjustments.
1. Loosen (A) 3-5 turns. Do not remove (A)! 2. Loosen (B) 3-5 turns. Do not remove (B) yet.
3. Insert tool (C) in opening. Hold tool (C) firmly to
engage spring force before removing screws (B). 4. Turn tool (C) one full turn counter-clockwise.
A
B

Adjusting Spring Tension
3A0138J 15
5. Replace one screw (B). Leave tool (C) in place. 6. Remove tool (C).
B
C
B
C
B
C

Adjusting Spring Tension
16 3A0138J
7. Pull hose to test tension. Repeat 3 - 7 if necessary. 8. Replace and tighten screws (B) and (A).
if
B
BA

Hose Stopper Installation
3A0138J 17
Hose Stopper Installation
Installing Meter
1. 2.
ti13525
1.

Parts: HS Models
18 3A0138J
Parts: HS Models
(For a complete list of model numbers, see page 3)
Ref.
No. Part No. Description Qty
1‡ SHAFT, spring (not shown) 1
2 15Y781 WASHER, flat (not shown) 1
3† SHAFT, swivel, (HSLC8,
HSMC8,HSLD5, HSLE3, HSMD5
and HSMDD models)
1
4‡ KEY, square (not shown) 1
6‡ BEARING, needle, swivel side (not
shown) 1
7‡ WASHER, flat, spring side 1
8‡ BEARING, needle, spring side (not
shown) 1
9‡ FLANGE, set, black 1
10‡ SPRING, power, 21 turn (not
shown) 1
11‡ COVER, spring, black (not shown) 1
12‡ GASKET (not shown) 1
14 15Y122 ADJUSTER, power spring 1
15 277867 WASHER, flat, square center 1
16 15U581 WASHER, flat 31 id 1
17 16A719 WASHER, flat 1
18 278151 SCREW, swivel shaft 1
19 107100 SCREW, cap 2
20†PACKING, o-ring 2
21†RING, backup I 2
22† SWIVEL, elbow (HSLC8, HSMC8
models 1
SWIVEL, elbow (HSLD5, HSLE3,
HSMD5, and HSMDD models 1
23 155470 FITTING, swivel, union (HSHC5,
HSLC8, HSHCD, HSMC8, HSPC5
models)
1
160327 FITTING, swivel, union (HSLD5,
HSLE3, HSMD5, and HSMDD
models
1
161037 FITTING, swivel, union (HSHFF,
HSPB8, HSHB7 models) 1
24 16A146 BASE, painted, all models white 1
16A147 BASE, painted, all models metallic
blue 1
16A148 BASE, painted, all models yellow 1
16A149 BASE, painted, all models desert
sand 1
25 15U448 RING, retaining, ext, 22mm 1
26 16A134 PEDESTAL, arm, swivel side, all
models white 1
16A135 PEDESTAL, arm, swivel side, all
models metallic blue 1
16A136 PEDESTAL, arm, swivel side, all
models, yellow 1
16A137 PEDESTAL, arm, swivel side, all
models desert sand 1
27 16A691 SCREW, socket head 2
28 24C986 HOSE, coupled, 50 ft (HSHC5
models) 1
24C987 HOSE, coupled, 75 ft (HSLC8 mod-
els) 1
24C988 HOSE, coupled, 50 ft (HSLD5 mod-
els) 1
24C989 HOSE, coupled, 30 ft (HSLE3 mod-
els) 1
24C990 HOSE, coupled, 75 ft (HSMC8
models) 1
24C991 HOSE, coupled, 50 ft (HSMD5
models) 1
24C992 HOSE, coupled, 75 ft (HSPB8 mod-
els) 1
126076 HOSE, coupled, 75 ft (HSHB7
models) 1
126075 HOSE, coupled, 50 ft (HSPC5
models) 1
30 16A121 ARM, guide, all models, white 2
16A122 ARM, guide, all models, metallic
blue 2
16A123 ARM, guide, all models, yellow 2
16A124 ARM, guide, all models, desert
sand 2
31 16A140 GUIDE, hose, all models, white 1
16A141 GUIDE, hose, all models, metallic
blue 1
16A142 GUIDE, hose, all models, yellow 1
16A143 GUIDE, hose, all models, desert
sand 1
32 186580 NUT, hex (HSHC5, HSHCF,
HSLC8, HSMC, HSPB8, HSPC5,
HSHB7 models)
1
15Y905 NUT, hex (HSLD5, HSLE3,
HSMD5, and HSMDD models)
33 104541 NUT, lock 8
34 BRACKET, roller 1
35 PIN, roller 2
36 BOLT, m6x 20 lg w/patch 4
37 ROLLER, hose 2
38 PIN, roller 2
39 ROLLER, hose 2
40NUT, lock, hex 1
41BUSHING, pawl (not shown) 1
42KIT, pawl, ratchet 1
43BOLT, m10 x 40 lg 1
44SPRING, sst 1
4615W036 LABEL, Warning 1
48SCREW, button head m6 4
49218341 STOP, hose (HSHC5, HSLC8,
HSMC8, HSPB8, HSHB7, HSPC5
models)
2
Ref.
No. Part No. Description Qty

Parts: HS Models
3A0138J 19
237873 STOP, hose (HSLD5 and HSMD5
models) 2
237874 STOP, hose (HSLE3 models) 2
50SCREW, mach, phil, pn hd 2
51NUT, hex, jam 2
52 111799 SCREW, cap, hex hd 6
53 16A390 NUT, hex 6
59RATCHET, Aluminum 1
60## ASSEMBLY, high pressure swivel
(HSHC5, HSHFF, HSPB8, HSHCD,
HSHB7, HSPC5)
1
Replacement Danger and Warning labels, tags and
cards are available at no cost.
† Included in Low / Medium Pressure Swivel and Seal
Replacement Kit 24C993- 1/2” NPSM, 24P059 - 1/2”
BSPT, or 24C994 - 3/4” NPSM, 24P060 - 3/4” BSPT
Included in Ratchet and Latch Replacement Kit
24C995
Included in Hose Guide Kit 24C996
Included in Bulk Head Hose Guide Kit 24C997
‡ Included in Spool Replacement Kit 24C998
Included in Hose Stop Replacement Kit 218341,
237873 or 237874
Included in Low / Medium Pressure Swivel Seal
Replacement Kit 24D134
## Included in High Pressure Swivel Assembly Kit
128920 - 1/2” NPSM, 128921 - 1/2” BSPT
Ref.
No. Part No. Description Qty

Parts: HS Models
20 3A0138J
50
51
49
39
38
37
35
36
34
31
52
53
53 30
30
52
23
48 59
44
33
28
42 43
40 46 19
24
3
21
20 26
27
7
16
25
15
32
17
18
14
9
22
Low/Medium
Pressure
Reels Only
High Pressure Reels
Only
60