GrainWood Montauk RMT0711 User manual

18"
32 ½"
52 ½"
RMT0711
RMT0712
RMT0720
RMT0724
Rustic Walnut
Rustic Off-White
Rustic Grey
Driftwood
Finish
Model #
2-person assembly
PH #2
Thank you for choosing Grain Wood Furniture, it is an honor to be in your home!
If you have any questions, feedback, or need replacement parts please contact us at:
grainwoodfurniture.com/help or [email protected]
Made in Brazil
REV - 09/2021 page 1/17
Montauk Collection
5-Drawer Chest
Assembly Instructions

page 2/17
Enjoy your 100% solid wood furniture!
PLEASE READ BELOW BEFORE BEGINNING ASSEMBLY
grainwoodfurniture.com/assembly-troubleshooting
ŸEnlist help from a friend or family member as most items require two
people for proper assembly.
ŸChoose a spacious, open area near where the piece will be located once
assembled. It is easier to move parts than to relocate the furniture after it
is fully assembled.
ŸDo not throw away packaging material until assembly is complete.
ŸAssemble the item on a soft surface, such as cardboard or an old blanket
in order to protect the finish from possible dents or scratches.
ŸLay out the parts in order and count them twice. In case any parts are
missing or damaged, document the problem with pictures and contact
support so we can make it right.
ŸSolid wood furniture may present imperfections such as wood knots,
minor splits or cracks which are a natural aspect of the material.
Whenever stability of the furniture is not compromised, we recommend
customers perform cosmetic touch-ups with wax crayon fillers sold at all
major hardware stores.
ŸIt is best to use the tools provided in the box, such as a hex key, because
they may be specially sized for the piece of furniture.
ŸWe do not recommend the use of power drills as they can damage your
furniture if not used correctly.
ŸUse a carpenter's square or hardcover book to check angles when
assembling drawers and doors. If they are not at 90 degrees, they will not
close properly.
ŸIf you have any problems, we are here to help. Just go to
grainwoodfurniture.com/help.
ŸSee grainwoodfurniture.com/care-guide for suggestions that will help
your furniture last for years.

A1 4,0x30 56 + 2
3,5x16 26 + 2
C1
D21
D34
8,0x30 72 + 2
4
3
A15 M4x22 20 + 2
B31 6,0x10 40 + 2
G1 10x10
50x50
28
G17 4
H6 10
A5
PZ04
2 + 1
F9
F8
2
FURNITURE ANTI-TIPPING RESTRAINT KIT
15x30 1
A8
3,0x20
4,0x45 12
A40
5
5
E13
E14
page 3/17
HARDWARE LIST
Before starting assembly
please verify the hardware
set is complete.
For missing hardware please
contact us at
grainwoodfurniture.com/help
WARNING:
CHOKING HAZARD
Small parts, not for children.
To be assembled by an adult.
!ATTENTION

5x
page 4/17
Part # Part #
05 09
45
02 04
Cleat Left side
2 1
06 10
2 5
01 03
1 1
Middle crosspiece Drawer right side
Rear crosspiece Drawer left side
07 15
08 16
11
13
HW
21
52
5
5
5
1
Upper/ lower crosspiece Profile “H”
Drawer front Back panel
Drawer bottom
Drawer back
Drawer bottom support
Hardware
12
Top Right side
Description Description
Qty. Qty.
BOX 1 BOX 2
01
04
06
06
06
05
05
05
05
07
07
03
15
02
16
16 02
10 11
13
12 09
08

5x
D21
D21
D21
2x
2x
2x
4x
5x
5x
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1
C1 C1
C1
C1
C1
C1
C1
C1
C1
C1
D34
A5
D34
A5
D34
A5
D34
A5
C1
1) Tip:
Use a hammer in case dowels
are hard to install by hand.
page 5/17
02
10
09
13
07
05
06
01
D34 03
D21 04
C1 8,0x30 72
A5 3,5x16 03

2)
E13
E13
E14
E14
page 6/17
E13
E13
E13
E13
E13
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
BACK
BOTTOM
TOP
FINISHED FRONT
03
B31 6,0x10 10
E13 5
RIGHT Side
Glide wheels should be
positioned towards the
front and bottom of the
side panel.
Need help?
Scan the QR code.
B31 B31E13
03

3)
E13
E13
E14
E14
B31
B31
B31
B31
B31
B31
B31
B31
B31
B31
E14
E14
E14
E14
E14
FINISHED FRONT
BACK
TOP
BOTTOM
B31 6,0x10 10
5
E14 LEFT Side
Glide wheels should be
positioned towards the
front and bottom of the
side panel.
Need help?
Scan the QR code.
04
page 7/17
B31
B31 E14
04

A40
A40
A40
A40
A40
A40
A40
4)
5)
A1
A1
A1
A1
A1
A1
06
FINISHED FRONT
BACK
TOP
A1 4,0x30 6
02
01
02
05
05
05
06
05
03
01
page 8/17
Attention: There
are no
predrilled holes
for the A1
screws on part
01.
Attention: There
are no predrilled
holes for the A1
screws on part
03.
A40 4,0x45 6
A1
A1 06
05

A1
A1
A1
A1
A1
6)
A1 A1
A1
A1
4,0x30
4,0x30
2
8
A1
A1
A1
A1
A1
A1
7)
07
07
07
07
07
03
07
03
04
01
06
05
page 9/17
Attention: There are no
predrilled holes for the
A1 screws on part 03.
Attention: There
are no predrilled
holes for the A1
screws on part
04.
A1 07

G17
G17
G17
G17
A5
A5
A5
A40 A40
A40 A40 A40
8)
A5
3,5x16 3
A5
4
G17
4,0x45 6
A40
ü
!
G1
!
G1
!G1
û
ü
G1
G1
G1
G1
9)
G1
G1 10x10 4
Make sure back panels are perfectly aligned with
side panels and top and there are NO gaps.
page 10/17
16
16
Attention: There are no
predrilled holes for the
A40 and A42 screws
G17