grandimpianti BTEL15*N4065 Owner's manual

Programming
MDC
Frontload Washers
Refer to Page 4 for Model Numbers
FLW8R
FLW8R
Part No. 801293R9
September 2007
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

801293 1
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
NOTE: The WARNING and IMPORTANT
instructions appearing in this manual are not meant
to cover all possible conditions and situations that
may occur. It must be understood that common
sense, caution, and carefulness are factors which
cannot be built into these washers. These factors
MUST BE supplied by the person(s) installing,
maintaining, or operating the washer.
Always contact the distributor, service agent, or the
manufacturer about any problems or conditions you do
not understand.
Failure to install, maintain, and/or operate
this machine according to the
manufacturer's instructions may result in
conditions which can produce bodily injury
and/or property damage. W030
WARNING

© Published by permission of the copyright owner.
2801293
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
Table of
Contents
Model Identification ........................................................................... 4
Preliminary Information.................................................................... 5
About the Control ................................................................................. 5
Glossary of Terms................................................................................. 5
Power Failure Recovery ....................................................................... 5
MDC Identification............................................................................. 6
SELECT CYCLE Keypads................................................................... 6
PREWASH Keypad.............................................................................. 6
START Keypad .................................................................................... 6
Display Identification ......................................................................... 8
Light Emitting Diodes (LEDs) ............................................................. 8
START LED......................................................................................... 8
WASH LED.......................................................................................... 8
RINSE LED .......................................................................................... 8
SPIN LED............................................................................................. 8
DOOR LOCKED LED ......................................................................... 8
Four 7-Segment Digits.......................................................................... 8
Washer Operation .............................................................................. 9
Start Up................................................................................................. 9
Ready Mode.......................................................................................... 9
OPL/Free Vend Mode........................................................................... 9
Closing Washer Door ........................................................................... 9
Signals................................................................................................... 9
MDC Special Features........................................................................ 10
Programming MDC .............................................................................. 10
Collecting Audit Information ............................................................... 10
Testing Machine and MDC Functions.................................................. 10
Rapid Advance Feature......................................................................... 10
Coin Drop ............................................................................................. 10
Start Pulse Operation ............................................................................ 10
Service Door and Coin Vault Openings ............................................... 10
Opening the Service Door .................................................................. 11
Washers Prepped for Central Pay System ....................................... 11
Entering the Manual Mode................................................................ 12
How to Enter the Manual Mode ........................................................... 12
Programming MDC............................................................................ 13
What Can Be Programmed? ................................................................. 13
Programmable Options Available......................................................... 13
1. Vend Price “-001”........................................................................ 14
2. Coin #1 Value “-002” .................................................................. 15
3. Coin #2 Value “-003” .................................................................. 16
4. Start Pulse Value “-004” .............................................................. 17
5. NORMAL 90 Prewash Fill/Agitate Time “-005”........................ 18
6. NORMAL 90 Wash Fill/Agitate Time “-006” ............................ 19
7. NORMAL 90 Rinse Fill/Agitate Time “-007” ............................ 20
8. NORMAL 90 Extra Rinse Fill/Agitate Time “-008”................... 21
9. NORMAL 90 Final Rinse Fill/Agitate Time “-009” ................... 22
10. NORMAL 60 Prewash Fill/Agitate Time “-010”...................... 23
11. NORMAL 60 Wash Fill/Agitate Time “-011” .......................... 24
12. NORMAL 60 Rinse Fill/Agitate Time “-012” .......................... 25
13. NORMAL 60 Extra Rinse Fill/Agitate Time “-013”................. 26

801293 3
© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
14. NORMAL 60 Final Rinse Fill/Agitate Time “-014” ................. 27
15. NORMAL 40 Prewash Fill/Agitate Time “-015”...................... 28
16. NORMAL 40 Wash Fill/Agitate Time “-016” .......................... 29
17. NORMAL 40 Rinse Fill/Agitate Time “-017” .......................... 30
18. NORMAL 40 Extra Rinse Fill/Agitate Time “-018”................. 31
19. NORMAL 40 Final Rinse Fill/Agitate Time “-019” ................. 32
20. PERM PRESS 60 Prewash Fill/Agitate Time “-020”................ 33
21. PERM PRESS 60 Wash Fill/Agitate Time “-021”.................... 34
22. PERM PRESS 60 Rinse Fill/Agitate Time “-022” .................... 35
23. PERM PRESS 60 Extra Rinse
Fill/Agitate Time “-023” ................................................................ 36
24. PERM PRESS 60 Final Rinse
Fill/Agitate Time “-024” ................................................................ 37
25. DELICATES 30 Prewash Fill/Agitate Time “-025” ................. 38
26. DELICATES 30 Wash Fill/Agitate Time “-026”...................... 39
27. DELICATES 30 Rinse Fill/Agitate Time “-027”...................... 40
28. DELICATES 30 Extra Rinse Fill/Agitate Time “-028” ............ 41
29. DELICATES 30 Final Rinse Fill/Agitate Time “-029”............. 42
30. Configuration “-030” ................................................................. 43
31. Default Cycle “-031” ................................................................. 46
Collecting Audit Information ............................................................ 47
How to Enter Audit Feature.................................................................. 47
Entering the Audit Feature by Manual Mode .................................. 47
Entering the Audit Feature with the Coin Vault Open .................... 47
How to Read Audit Data....................................................................... 47
How to Exit Audit Feature When Using Manual Mode ....................... 47
Testing Machine and MDC Functions.............................................. 48
How to Enter Testing Feature............................................................... 48
How to Start Tests ................................................................................ 48
How to Exit Testing Feature................................................................. 48
Diagnostic Test Descriptions................................................................ 49
Show Fill Time Test......................................................................... 49
Show Drain Time Test ..................................................................... 49
Temperature Sensor Display Test.................................................... 49
Production Test Cycle........................................................................... 50
To Enter Production Test Cycle....................................................... 50
To Exit Production Test Cycle......................................................... 50
Rapid Advance Feature...................................................................... 53
How to Enter Rapid Advance from Ready Mode................................. 53
How to Enter Rapid Advance During an Active Cycle........................ 53
How to Use Rapid Advance ................................................................. 53
How to Exit Rapid Advance Feature .................................................... 53
Default Washer Settings..................................................................... 54
Default Settings .................................................................................... 54
Default Cycle ........................................................................................ 54

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 801293
4
Model Identification
Information in this manual is applicable to these washer
models:
*Add Letter To Designate Color. W – White Q – Bisque N – Stainless Steel
BTEL15*N4065 NTGL19*N4067
BTEL17*N4065 NTGL79*N4067
BTEL75*N4065 NTGX19*N4067
BTEL77*N4065 NTGX79*N4067
BTEX15*N4065 NWFL44*N4000
BTEX17*N4065 NWFL45*N4000
BTEX75*N4065 NWFL64*N4000
BTEX77*N4065 NWFL84*N4000
BWFLE4*N4000 NWFL85*N4000
BWFLE5*N4000 NWFX64*N4000
BWFL74*N4000 NWFX65*N4000
BWFL75*N4000 NWFX74*N4000
BWFXE4*N4000 NWFX75*N4000
BWFXE5*N4000 STEX17*N4064
BWFX74*N4000 STEX17*N5754
BWFX75*N4000 STEX77*N4064
HTEX17*N4064 STEY17*N4064
HTEY17*N4064 STEY17*N5754
HWFX64*N4000 STEY77*N4064
HWFY64*N4000 SWFL74*N4000
HWFY65*N4000 SWFX64*N4000
NTEL17*N4064 SWFX65*N4000
NTEL77*N4064 SWFX74*N4000
NTEX17*N4064 SWFX75*N4000
NTEX17*N4067 SWFY64*N4000
NTEX77*N4064 SWFY65*N4000
NTEX77*N4067

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 5
801293
Preliminary Information
About the Control
MDC on the commercial washer is a programmable
control that lets the owner control machine features by
pressing sequences of SELECT CYCLE keypads.
MDC allows the owner to program cycle steps, set
vend prices, retrieve audit information and run
diagnostic tests. Washers shipped from the factory
have a default cycle (PERM PRESS 60) built in.
IMPORTANT: In the event of a power failure,
MDC will not have to be reprogrammed. It is
designed with a memory system that will remember
how it was programmed (for up to six years) until
the electrical power is restored.
IMPORTANT: It is extremely important that the
washer has a positive ground and that all
mechanical and electrical connections to MDC are
made before applying power to or operating the
washer.
Glossary of Terms
The following are a few terms and abbreviations to
learn. These are referred to throughout the manual:
Four-Digit Display – This term refers to the window
area of the control that displays values.
LED (Light Emitting Diode) – This term refers to the
lights on the keypads and status words of the control.
Power Failure Recovery
If power fails during an active cycle, the cycle status is
saved in memory. If door is locked when power is
restored, the washer will automatically resume the
cycle. If door is unlocked when power is restored, the
user must press the START keypad to resume the
cycle.

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 801293
6
MDC Identification
SELECT CYCLE Keypads
SELECT CYCLE keypads are used to select the
specific washer cycle. These keypads include
NORMAL 90, NORMAL 60, NORMAL 40, PERM
PRESS 60, and DELICATES 30. The selection of one
of these keypads will light up the corresponding LED.
The SELECT CYCLE keypads are not active after the
first fill cycle of the washer. Pressing the flashing
START keypad will confirm selection and cycle will
begin when vend is satisfied.
NOTE: The number on each keypad corresponds
to the wash temperature in °C.
PREWASH Keypad
The PREWASH keypad is used to add a prewash
setting to any select cycle. The PREWASH keypad
must be pressed when the control is in the Start Mode.
The PREWASH LED will light when PREWASH is
active.
START Keypad
The START keypad is used to start the washer after the
full vend price has been satisfied.
The SELECT CYCLE, PREWASH, and START
keypads are used in various combinations for
programming cycles, retrieving audit information,
running diagnostic tests, and other operations
described in Entering Manual Mode.
NORMAL 90
NORMAL 60
NORMAL 40
PERM PRESS 60
DELICATES 30
FLW1946N
90
FLW1947N
60
FLW1948N
40
FLW1949N
60
FLW1950N
30
PREWASH
START
FLW13R
FLW14R

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT
MDC Identification
7
801293
Figure 1
FLW8R
1Four 7-Segment Digits
2Four-Digit Display
3LED Status Lights
4SELECT CYCLE Keypads
5START Keypad
6LED Light
6
2
3
1
5
4

© Published by permission of the copyright owner – DO NOT COPY or TRANSMIT 801293
8
Display Identification
Light Emitting Diodes (LEDs)
LIGHT EMITTING DIODES (LEDs) are used to
indicate the chosen cycle status. Refer to LED
descriptions below.
START LED
The START keypad LED flashes whenever the washer
is not in a cycle and the full vend price has been
satisfied. When the START keypad is pressed, the
cycle will begin or resume. The START LED will shut
off when the START keypad is pressed.
WASH LED
The WASH LED is lit at the beginning of a wash cycle
and will remain lit until the wash cycle is complete.
RINSE LED
RINSE LED is lit at the beginning of the rinse or extra
rinse cycle and will remain lit until the cycle is
complete.
SPIN LED
SPIN LED is lit for all spins.
DOOR LOCKED LED
DOOR LOCKED LED is lit whenever the door is
locked. The door cannot be opened when the DOOR
LOCKED LED is lit.
Four 7-Segment Digits
The 7-SEGMENT DIGITS are used to display the
time remaining in a cycle, vend price, error messages
and descriptive codes. When displaying the time
remaining, the time value is displayed on the right side
of the display. When displaying the vend price, the
value is displayed on the left side of the display.
During diagnostic testing or manual programming of
the control, these digits will display descriptive codes
and values (as described in Entering the Manual
Mode).