Grandstream Networks DP750 User manual

Home
PBXware
SERVERware
TELCOware
SIPmon
SIPProt
Desktop & Mobile
BRM
UADs
Appliances
EOL
From Bicom Systems Wiki
Contents
1 Introduction
■
2 Video Tutorial
■
3 Requirements
■
3.1 Identifying device model
■
3.2 Device firmware
■
3.3 DHCP server
■
3.4 PBXware version
■
4 Installation
■
4.1 Power adapter
■
4.2 Power over Ethernet (PoE)
■
4.3 Find the device IP address
■
4.4 Reset to factory settings
■
5 Registering device
■
5.1 Manual configuration
■
5.2 Auto Provisioning
■
Introduction

This Configuration Guide is written as general guide on how to configure the Grandstream
device model DP750 to work with PBXware 4.1.3.
Video Tutorial
Video tutorial explaining Auto Provisioning setup for Grandstream Phone on PBXware 4.
Video tutorial explaining Auto Provisioning setup for Grandstream Phone on PBXware 5.
Requirements
Identifying device model
To start and successfully complete registration of your Grandstream device you need to know
which device model you will setup.
From the back of each Grandstream device there are exact model information that you should
check. Although different device models can have exactly the same requirements and
installation procedure, device models can also have significantly different requirements and
installation procedure, so that ignorance of your own model may result in the inability to
successfully set up your device.
Device firmware
Make sure that your device is loaded with appropriate firmware version, 1.0.3.23.
■
To find out the firmware version of your Grandstream device model open a new browser
■
window and enter your device IP address in order to access the device web administration
interface login screen. Example: http://192.168.1.22.
Login to device web administration interface with your username and password. Please note,
■

factory default login details are username: admin and password: admin.
DHCP server
Fully configured and operational DHCP server.
PBXware version
PBXware version 4.1.3.0
In order to find out the PBXware version:
Login to PBXware
■
Navigate to Settings: About.
■
On the top of About page is a code similar to this one PBXware Edition: Business, Release:
4.1.3.0 (387597b7), Running: 1.8.32.1-gc-b47edc45, PBXware Proxy v4.1.3 (62b7bcd),
API: 4.1, libmemcached version: 1.0.14, where Release denotes the exact version of your
PBXware.
Installation
This chapter describes how to install and connect the device to the electrical power and data
network as well as how to apply factory settings.
The following topics are covered:
Power adapter
■
Power over Ethernet (PoE)
■
Factory Settings
■
Power adapter
Connect the Network and Power
Connect the DC plug on the power adapter to the DC port on the device and connect the other
■
end of the power adapter into an electrical power outlet.
Connect the ethernet cable between the Internet port on the device and the network port on a
■
router or switch to access LAN.
NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.
Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.
Power over Ethernet (PoE)
Connect the Network (only)
Using a regular ethernet cable, your device can be powered from a Power over Ethernet (PoE)
compliant router or switch.
Connect the Ethernet cable between the Internet port on the device and an available port on
■
the in-line power router or switch.

NOTE: If you are using Power over Ethernet (PoE), you don't need to connect the AC adapter.
Make sure the Ethernet cable and router or switch is Power over Ethernet (PoE) compliant.
Find the device IP address
Find out your Grandstream device IP Address.
Press the Menu button on the handset.
■
Go to Status menu.
■
The IP address will be displayed on the handset display.
Reset to factory settings
This step is not required for brand new out-of-the-box devices, however, if the device has been
already used then it is a must.
Open a new browser window and enter your device IP address in order to access the device
■
web administration interface login screen. Example: http://192.168.1.22.
Login to device web administration interface with your username and password. Please note,
■
factory default login details are username: admin and password: admin.
Click on Maintenance in the top navigation menu.
■
Click on Factory Reset in the left navigation menu.
■
Click Reset button in the Configure WEB UI button section. Device will be reset to the
■
factory settings and reboot.
Wait sometime prior for device to reboot.
■
NOTE: Do not unplug or remove power to the device while it is updating firmware and
configurations.
Registering device
This chapter describes how to identify Grandstream device model, requirements that must be
met and how to register the device using manual configuration or auto provisioning.
The following topics are covered:
Manual configuration
■
Auto provisioning
■
Manual configuration
This chapter describes how to set UAD settings, create PBXware extension and register the
device.
The following topics are covered:
UAD settings
■

Creating extension
■
Registering device
■
UAD Settings
UAD settings
Login to PBXware web administration interface
Open a new browser window and enter the IP address in order to access the PBXware web
■
administration login screen. Example: http://192.168.1.10.
Login to PBXware with your e-mail address and password.
■
UAD settings
Navigate to Settings:UAD.
■
Make sure Grandstream UAD is enabled. To check the UAD status click on the edit icon
■
corresponding to your Grandstream device.
Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.
■
Click on the Save button to save changes.
■
Creating extension
Creating Extension
Add Extension
Navigate to Extensions. Click on Add Extension.
■
The standard options window will be shown below.
■
Select Grandstream device model from the UAD select box.
■
Select Location: Local or Remote.
■
Local is for all extensions registered on the LAN and Remote is for all extensions
registered from remote networks, WAN, Internet etc.

Click on the Next step button.
■
Extension values
Enter values into the required field text boxes.
REQUIRED FIELDS:
Name
■
Enter a name for the extension being created. Example: John Smith.
E-mail
■
Enter the e-mail address associated with this extension. This e-mail address will receive all
system notification messages. Example: [email protected]
Department
■
Department to which extension will belong to. Example: Sales.
Click on the Save button.
■
Registering device
This chapter describes how to register Grandstream device using Hostname or IP Address.
Hostname or IP Address
Login to device web administration interface
Open a new browser window and enter your device IP address in order to access the device
■
web administration interface login screen. Example: http://192.168.1.22
Login to device web administration interface with your username and password. Please note,
■
factory default login details are username: admin and password: admin.
Click on Profiles in the top menu.
■
Enter or set the following details into the respective fields.
■
REQUIRED FIELDS:
Account Active
■
Make sure the Yes radio box is selected.
Sip Server
■
Enter the Hostname or IP Address of the PBXware.

- Example for Hostname: voip.bicomsystems.com
- Example for IP Address: 192.168.1.10
Click Save button.
■
Click on Dect in the top menu.
■
Click on SIP Account Settings in the left menu.
■
SIP User ID
■
PBXware extension number, example 1003.
Authenticate ID
■
Usually the same number as the SIP User ID.
Password
■
The Secret of the extension as received in the e-mail associated with this extension.
Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created
extension.
Click on the Save and Apply button.
■
If everything is done as above described, you should have successfully registered your device
■
to PBXware. Dial *123 to verify registration.
Auto Provisioning
This chapter describes how to set UAD settings, create PBXware extension and register the
device using DHCP or Static IP address.
The following topics are covered:
UAD Settings
■
Creating Extension
■
Registering device
■
UAD Settings

UAD settings
Login to PBXware web administration interface.
Open a new browser window and enter the IP address in order to access the PBXware web
■
administration login screen. Example: http://192.168.1.10.
Login to PBXware with your e-mail address and password.
■
UAD settings.
Navigate to Settings:UAD.
■
Make sure Grandstream UAD is enabled. To check the UAD status click on the edit icon
■
corresponding to your Grandstream device.
Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.
■
Click on the Save button to save changes.
■
Creating Extension
Creating Extension
Add Extension
Navigate to Extensions. Click on Add Extension.
■
The standard options window will be shown below.
■
Select Grandstream device model from the UAD select box.
■
Select Location: Local or Remote.
■
Local is for all extensions registered on the LAN and Remote is for all extensions
registered from remote networks, WAN, Internet etc.
Click on the Next step button.
■
Extension values
Enter values into the required field text boxes.
REQUIRED FIELDS:
Name
■
Enter a name for the extension being created. Example: John Smith.

E-mail
■
Enter the e-mail address associated with this extension. This e-mail address will receive all
system notification messages. Example: [email protected]
Auto Provisioning
■
Set to Yes.
MAC Address
■
Enter Grandstream device MAC address. Example: 000B82123456. MAC address can be
found at the back of the device.
Click on the Save button.
■
Registering device
This chapter describes how to register Grandstream device using DHCP, TFTP or HTTP &
HTTPS.
The following topics are covered:
DHCP
■
TFTP or HTTP & HTTPS
■
DHCP
Configure DHCP
Make sure your DHCP router is configured to use option 66 to automatically instruct device
■
with the URL for auto provisioning. For more information refer to your router documentation
or contact your network administrator.
Phone first boot or user initiated reboot
Auto provisioning process will start during device first boot or after reboot process has been
■
initiated by user. DHCP server will instruct the device where from to pickup appropriate
configuration file. If everything is done as above described, you should have successfully
registered your device to PBXware. Dial *123 to verify registration.
TFTP or HTTP & HTTPS
Open a new browser window and enter your device IP address, e.g. http://192.168.1.22.
■
Enter username and password and press Confirm button. NOTE: Factory default login
■
details are username: admin and password: admin.
Click on Maintenance at the top navigation menu.
■
Click on Provisioning at the left menu.
■
Enter Auto Provisioning username and password into HTTP/HTTPS User Name and
■

HTTP/HTTPS Password fields.
Choose what server type you intend to use in the Provisioning via field: TFTP, HTTP and
■
HTTPS. NOTE: Our recommendation is to use the HTTP.
If the Server Type is HTTP or HTTPS enter Hostname or IP Address, followed
then by /prov in the Config Server Path field.
Example for Hostname using HTTP: abc.bicomsystems.com/prov
Example for Hostname using HTTPS: abc.bicomsystems.com/prov
Example for IP Address using HTTP: 192.168.1.10/prov
Example for IP Address USING HTTPS: 192.168.1.10/prov
If you choose to use server type TFTP enter Hostname or IP Address in the
Config Server Path field.
Example for Hostname: voip.bicomsystems.com

Example for IP Address: 192.168.1.10
Click on Save and Apply button.
■
Click Reboot button in the top right of the web interface.
■
You'll have to wait couple of seconds for the configuration to be updated. NOTE: Do not power
■
off your device.
Auto provisioning process will start during device reboot process, device will pickup
■
appropriate configuration file from PBXware. If everything is done as above described, you
should have successfully registered your device to PBXware. Dial *123 to verify registration.
Retrieved from "http://wiki.bicomsystems.com/Grandstream_DP750"
Disclaimers - About Bicom Systems Wiki