Great day UVRS100BL User manual

PAGE 1 OF 4
THE RUMBLE SEAT
MODEL: UVRS100BL-300 LB. WEIGHT CAP.
READ ALL INSTRUCTIONS AND THE ADDITIONAL LIST OF WARNINGS BEFORE USING THE
RUMBLE SEAT
NOTE: Failure to read instructions before use could result in injury or death.
Instructions for Installation and Use:
FIG. 1
PAGE 2 OF 4
**NOTE**PLEASE REMOVE ALL PARTS
FROM BOX AND CHECK THE PARTS
AGAINST THE CONTENTS LIST BEFORE
BEGINNING ASSEMBLY. ANY MISSING
OR DAMAGED PARTS NEED TO BE
REPORTED TO GREAT DAY, INC.
CONTENTS: SEE FIG. 1
1–BACKREST FRAME WITH 2 CUSHIONS
1–SEAT FRAME WITH 2 CUSHIONS
1–SEATBELT STRAP W/ 2 MALE BUCKLES
4–5/16” QUICK PINS
2–ARMRESTS
1–HARDWARE PACKET
2–LEG ASSEMBLIES W/ MOUNTING
BRACKETS
HARDWARE PACKET INCLUDES:
4–5/16” X 2 1/2" BOLTS
4–5/16” X 1” BOLTS
4–5/16” FENDER WASHERS
8–5/16” X 1 3/4" BOLTS
2–5/16” X 2” BOLTS
14 –5/16” LOCKNUTS
24 –5/16” FLAT WASHERS
2–FEMALE SEAT BELT BUCKLES
2–SAFETY ATTACHING STRAPS W/THUMB
RELEASE BUCKLES

PAGE 2 OF 4
FIG. 2 FIG. 2A FIG. 2B
FIG. 3 FIG. 3A
FIG. 4
FIG. 5
STEP 1: SEE FIG. 2-
ATTACH LEG ASSEMBLIES TO THE BOTTOM OF THE SEAT FRAME USING 4-5/16” x 1 3/4”
BOLTS, 8-FLAT WASHERS & 4-LOCK NUTS. **NOTE**THERE ARE 4 DIFFERENT LEG
ASSEMBLY POSITIONS (2 ON SEAT FRAME & 2 ON LEG ASSEMBLIES) TO ENSURE PROPER
LEVEL POSITIONING IN THE BED OF YOUR PARTICULAR UTV. SEE FIG. 2A & FIG. 2B.**
STEP 3: SEE FIG. 4
SECURE BACK FRAME TO SEAT
FRAME USING 2-5 /16” x 2” BOLTS,
WASHERS & LOCKNUTS. TIGHTEN
SECURELY.
STEP 2: SEE FIG. 3 & 3A
REMOVE FEMALE ENDS OF SEAT
BELTS FROM PACKET & PLACE
LOOP END AROUND EAR OF SEAT
SECTION. THIS IS THE UPRIGHT
WHERE THE SEAT SECTION &
BACKREST SECTION ATTACH
TOGETHER. REPEAT FOR
SECOND FEMALE END OF SEAT
BELT. TIGHTEN SECURELY.
STEP 4: SEE FIG. 5
ATTACH ARMRESTS TO SEAT
FRAME AND BACKREST FRAME
USING 4-5 /16” x 2 1/2” BOLTS,
WASHERS & LOCKNUTS.
TIGHTEN SECURELY.

PAGE 3 OF 4
FIG. 6
FIG. 7
FIG. 8
FIG. 9
STEP 5: SEE FIG.6
PLACE FULLY ASSEMBLED RUMBLE SEAT
INTO THE CARGO AREA OF UTV WITH
RUMBLE SEAT BACKREST AGAINST THE CAB
OF UTV.
**NOTE**THE RUMBLE SEAT IS INTENDED TO
FACE THE REAR OF THE UTV WITH
BACKREST AS CLOSE TO THE ROLL BARS AS
POSSIBLE.
STEP 6: SEE FIG. 7
MARK LOCATION TO DRILL THE 4 HOLES
FOR ATTACHING THE MOUNTING
BRACKETS TO THE BED OF THE UTV.
STEP 8: SEE FIG. 9
BOLT THE MOUNTING BRACKETS
TO THE BED OF THE UTV USING 4 –
5/16” X 1” OR 4 - 5/16” X 1 3/4"
BOLTS, (WHICHEVER LENGTH IS
APPROPRIATE FOR THE UTV) & 4 –
5/16” FENDER WASHERS (ON THE
UNDERSIDE OF CARGO BED), & 4 –
5/16” LOCKNUTS. TIGHTEN
SECURELY.
STEP 7: SEE FIG. 8
REMOVE RUMBLE SEAT & DRILL
THE 4 MARKED LOCATIONS IN THE
BED OF THE UTV USING A 7/16”
DRILL BIT. **NOTE**BE SURE YOU
ARE NOT DRILLING INTO FUEL
TANK OR FUEL LINES.

PAGE 4 OF 4
FIG. 10
FIG. 10A FIG. 10B
PAGE 5 OF 5
DO NOT USE THE RUMBLE SEAT WITHOUT SAFETY ATTACHING STRAPS IN PLACE.
IT IS ABSOLUTELY IMPERATIVE THAT THE SAFETY ATTACHING STRAPS BE INSTALLED AS
SHOWN IN STEP 9 TO PREVENT ACCIDENTAL OR UNINTENDED TILTING OF UTV BED!
SAFETY BELTS MUST BE WORN AT ALL TIMES WHEN SEATED IN THE RUMBLE SEAT.
TO THE OWNER/OPERATOR OF THE UTV: DO NOT ALLOW ANY PERSON TO SIT ON
RUMBLE SEATS WITHOUT HAVING THE SEATBELTS CONNECTED AND SECURED!
DO NOT EXCEED THE 300 LB. WEIGHT CAPACITY (TOTAL WEIGHT OF BOTH PASSENGERS)
OF THE RUMBLE SEAT.
For more information about this or other products, contact us at:
Great Day, Inc.
604 Kimbrough Dr. * Tallulah, LA 71282 * [phone] * www.greatdayinc.com
STEP 9: SEE FIG. 10 & FIG. 10A
ATTACH THE RUMBLE SEAT TO UTV
FRAME USING SAFETY ATTACHMENT
STRAPS. PUT LOOP ENDS AROUND
BACK OF RUMBLE SEAT FRAME AND
UTV ARM REST/SEAT FRAME. SEE
FIG. 10B -SECURE WITH QUICK
RELEASE BUCKLE.
**NOTE**THE RUMBLE SEAT MAY BE REMOVED FROM UTV BY REMOVING THE QUICK
PINS THAT SECURE THE FRAME TO THE MOUNTING BRACKETS.