Gree GPC12AE-A3NNA8A User manual

Change for Life
Owner's Manual
Portable Air Conditioner
Portable Air Conditioner
Thank you for choosing Portable Air Conditioner,please read this owner’s
manual carefully before operation and retain it for future reference.
GPC12AE-A3NNA8A
GPH12AE-A3NNA8A

SUMMARY
1. SUMMARY .................................................1
※. USAGE NOTICE ........................................ 3-- 4
7. ACCESSORIES AND INSTALLATION OF HEAT EXHAUST HOSE 12--14
9. ELECTRIC SCHEMATIC DIAGRAM .........................16
2. WORKING PRINCIPLE.......................................1
3. STRUCTURE...............................................2
4. OPERATING METHODS ................................ 3--6
5. .....7--9
8. CARE AND MAINTENANCE ...........................15--16
10. TROUBLESHOOTING .....................................17
11. USER NOTICES .........................................18
12. AFTER SALES SERVICE..................................19
13. INSTALLATION AND MAINTENANCE OF HEALTHY FILTER ..20
6. OPERATION OF THE REMOTE CONTROLLER ............ 10--11
.
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER

－2－
SUMMARY
－1－
This MOBILE AIR CONDITIONER is a small, movable air conditioner. It possessed the functions
of COOL, DRY and the Separate Ventilation, and depends on different places, it can
be moved as will.
It is fit for home and office use, especially fit for the house with many rooms.With the compact
configuration, excellent workmanship, elegant appearance, it looks like a standing Benz car. It is
convenient for moving, energy saving, and with low noise.
Note: Please read this manual carefully before operating the unit, the manual is used for reference,
and the technical parameters are subject to change without notice.
WORKING PRINCIPLE
With the help of upper motor, the airflow of indoor pass through the evaporator becomes the
cooled wind, but with the help of lower motor, the airflow of indoor pass through the condenser
becomes the heated wind. There is two duct systems designed in its structure.The heated wind is discharged
by the rear outlet, the cooled wind is discharged by the front outlet,flow-guided by the louver,and it
brings the gentle cooling airflow,and the low temperature environment is maintained.
The Working Principle
Cooled wind
Upper motor
Lower motor
Evaporator
Airflow 1
Airflow 2
Capillary
Heated wind
Condenser

-2-
STRUCTURE
Front
Rear
Control panel
Air outlet
Handle
Upper air inlet grille
Heat air exhaust vent
Power cord
Lower air inlet grille

16℃- 30℃.
The working range of COOL mode and DRY mode：
Place requirements:
OPERATING METHODS
- 3 -
※.USAGE NOTICE
Unpack the Air Conditioner
Remove packaging materials
Remove and properly dispose the packaging materials. Remove tape and glue residue from surfaces before
WARNING
Excessive Weight Hazard
Use two or more people to move and install the air conditioner.
Failure to do so can result in back or other injury.
turning on the air conditioner. Rub a small amount of liquid dish soap over the adhesive with your fingers.
Wipe with warm water and dry it.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue.
These products can damage the surface of your air conditioner.
•
•
•
Place the air conditioner on a smooth level floor that strong enough to support the unit.
Allow at least 12 inches (50 cm) of air space on all sides of the unit for good air ventilation.
Place the unit in an area where the temperature will not fall below 16℃(61 ). The coils will be covered
with frost at temperatures below 16℃(61 ), and this may reduce performance.
NOTE: The portable air conditioner has wheels for easy movement, but it should only be rolled on smooth and
flat surfaces.Do not attempt to roll the portable air conditioner on carpet or over objects.
12″(50 cm)
min.
12″(50 cm)
min.
The appliance is for indoor use only,but shall not be installed in the laundry.•
The Max Cooling operation temperature for the air conditioner is 35 ℃.
The appliance shall be installed in accordance with national wiring regulations.
•
°F(86 )
°F
°F
°F
°F

Power must adopt the rated voltage and special circuit for AC. And diameter of power cord should be big enough.
- 4 -
Electrical Requirements
death, fire, or electrical shock.
WARNING
Electrical Shock Hazard
Plug into a grounded 3-prong outlet.
Failure to follow these instructions can result in
Do not use an extension cord.
Do not use an adapter.
Do not remove ground prong.
Time-delay fuse or time-delay circuit breaker is recommended to be used.
All wiring must comply with local and national electrical codes and should be installed by a qualified electrician.
If you have any questions, contact a qualified electrician.
※.USAGE NOTICE
OPERATING METHODS
The wiring must be operated by the professional personnel by
circuit. Don't connect earth wire to water pipe or gas pipe. When the air conditioner is not used, please pull
out the power plug or cut off power supply.
following the national regulation.There must be
electric leakage protect switch and magnetic and heat drop-off air switch that with enough capacity in fixed
Including an air switch with suitable capacity, please note the following table. Air switch should be included
20A
Air switch capacityAir-conditioner (W)
GPC12AE-A3NNA8A
GPH12AE-A3NNA8A
magnet buckle and heating buckle function, it can protect the circuit-short and overload. (Caution: please do
not use the fuse only for protect the circuit)

ON/OFF key
MODE key
COOL mode
LED screen
DRY mode
FAN mode
WATER FULLlight
Control panel and the function
1. "ON/ OFF " key
Press once to start and press once more to stop the unit.
2."MODE" key
Press this button to change the operation mode in order of: GPC12AE-A3NNA8A:
COOL → DRY → FAN → COOL → DRY → FAN HEAT .
→
COOL ; GPH12AE-A3NNA8A:
3. key
In "COOL" or “HEAT”mode, press
" ""
Names and Functions Remote Controller
"
will increase morfdetcelesebnacerutarepmetehT
Press
.
" once, the temperature will decrease 1 "once,
"
℃( 1 )
°F
"
the temperature
“” “ ”key
- 5-
OPERATING METHODS
.
1
℃( 1 F)
°16℃(61 )～30℃( 86
°F°F).
GPC12AE-A3NNA8A:
ON/OFF key
MODE key
COOL mode
LED screen
DRY mode
FAN mode
HEAT mode
“” “ ”key
GPH12AE-A3NNA8A :

1). To select a place near the door and window, install the exhaust duct.
2). Press"MODE"key to select"COOL" mode.
3). Press key to set the suitable temp.
or
When the unit is running in the COOL mode, in order to keep the good cooling effect,
please pay more attention to:
1) If there is the direct sunlight near the window, please use the curtain to shield .
2) Donot use other heat sources in the air conditioner room.
Please close the door and window, in order to obtain the better dehumidifying effect:
Press "MODE" key, select the "DRY" mode, the unit will run in the "DRY" mode, at the
same time, the upper motor is running at the low speed, it is not adjustable.
COOL mode
1). Press “MODE ” key to select “HEAT”mode .
2). Press
HEAT
(not for only
cooling unit )
mode
CAUTION
DRY mode
When the unit runs in FAN mode, it can select 3 speeds.
FAN mode
When the tanks gets full
GPH12AE-A3NNA8A:HEAT light ) will flash and the buzzer will sound eight times,
the indicator(GPC12AE-A3NNA8A:WATER FULL light ;
LED window shows error code “ H8 ”, at the same time the unit stop running. We should
drain off the water .
WATER
DRAINAGE
"
"""
- 6-
OPERATING METHODS
16℃( 61 )～30℃86 .
°F°F
key to set the suitable temp.
or "
"""16℃( 61 )～30℃86 .
°F°F

- 7 -
●
AUTO
COOL
DRY
FAN
HEAT (Note:no for coolling only
unit As for cooling only unit, it won’t
have any action when it receives
the signal of heating operation.
FAN FAN speed button
Press this button once, fan speed will change
as below: Auto
Low speed Middle speed
High speed
Note:Under the Dry mode, the fan speed isn't
●
Simpleness swing mode is defaulted for wireless
remote control, in this mode, press this button,
(＋/－)
16 ～30
℃
●
Note: Be sure that there are no obstructions between receiver and remote control; Don't drop
or throw the remote control; Don't let any liquid in the remote control and put the remote control
directly under the sunlight or any place where is very hot
.
Signal transmitter
Remote control
ON/OFF
ON/OFF button
Press this button, the unit will be started or stopped,
which can clear the timer or sleeping function of
last time.
●
)
TEMP. button
(＋/－)
When press +button,the setting temp. will b e
eht,nottub-sserpnehW,)1(1ybdesaercni
setting temp. will be decreased by 1
The temp. will be changed quickly
the button continuously and setting temp. range
℃
is
by pressing
●
●
●
Swing up and down button
℃
below.
Press this button, the running mode will change as
Mode button
MODE
could turn on or turn off the Up and down
swing function.
When unit is turned off, synchronously press
"+" and Up and down swing buttons, it could
be switched between the simpleness swing
mode and stationary swing mode, at this time,
blinks 2 seconds.
In Stationary swing mode, press this button,the
angle for Up and down swing as show in below:
When up and down swing louver is working,
when turn off the unit, the siwng louver will
●
immediately stop at current position.
shows up and down swing louver swings back
and forth as show in the above figure.
adjustable, low fan speed is imperative,
but when operating this button, the wireless
remote control will send this signal.
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
°F
(1 )
°F
℃°F°F
FAN
AUTO
OPER
HEALTH
AIR
FILTER
TURBO
ON/OFF
X-FAN
HOUR
HUMIDITY
ON/OFF
MODE
FAN
X-FAN
TURBO
TEMP TIMER
SLEEP LIGHT

- 8-
HEALTH function:there is no this function
for this unit. If press this key,the main unit
will click, but it also runs under original status.
wireless remote control, fan speed automatically
rotates, when repress this button, the fan speed
will run at previous setting fan speed.
TIMER
●
●
NOTE: This Remote control is universal, it could be used formany units, some buttons
of this control which are not available to this unit will not be described below.
On the status of the unit on, press this
button to set timer off. On the status of
the unit off, press this button to set timer
on. Press this key once, words Hour on(off)
will appear and flicker. In which case, press
+/- button to adjust time (press+/- button
the setting time range is from 0.5 to 24 hr. ;
continuously to change timing value quickly ),
then remote controller will send out the signal
immediately and hour on/off will stop flickering.
If the time of that no press timer button
under flickering status is above 5s,the timer
setting will quit. If the timer has been set,
press this button once again to quit it.
press this key once again to fix the time,
There is no this function for this unit.If
press this key,the main unit will click,but
it also runs under original status.
Temp. display button
TEMP
●
●Save energy function: this unit has no this
function, press this button, the main unit will
click, "SE" will be displayed on the LED of
Remote control
button Left and right swing button
Timer button
●The key can be changed between setting
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
temperature and surrounding temperature,
and the main unit ill click.w
FAN
AUTO
OPER
HEALTH
AIR
FILTER
TURBO
ON/OFF
X-FAN
HOUR
HUMIDITY
ON/OFF
MODE
FAN
X-FAN
TURBO
TEMP
TIMER
SLEEP LIGHT