Greenfield TS3 User manual

Single Stage Carbonblock TS3 Filter
Install Guide

Step 1 - Inventory Parts Received
1. This Instruction Sheet
2. Filter housing (assembled)
3. 2 small mounting screws
4. Water Supply Black Tee Connector
(3/8 push connector x 3/8 male
compression x 3/8 female compression)
5. Water dispenser (optional)
6. Direct Connect Faucet parts (optional)
7. Connecting tubing (3/8 plastic)
8. Faucet hose connector fitting
9. Filter housing wrenches
Step 2 - Prepare Filter Housing
1. Select a suitable location for the filter housing.
a. Location should be accessible for filter cleaning and/or replacement
Step 3 - Install the Water Supply Tee Connector
1. Turn o!the cold water supply valve under the sink. If there is no valve, turn o!the water to
your house at the main meter.
2. Open the cold water faucet to let o!the pressure. Make sure the valve is o!and the faucet is
not dripping.
3. Unscrew the nut that holds the cold water supply line into the pipe where you just turned the
water o!from.
4. Install the Tee Connector onto the exposed threads and tighten. BE CAREFUL NOT TO
CROSS THREAD
5. Screw water faucet supply line back onto the tee connector.
NOTE: Do NOT turn the cold water line back on yet, the water will flow directly out of the tee
connector and flood your kitchen.
Step 3 Alternative Option: Direct to Kitchen Faucet Install
If connecting directly to the cold water faucet and not using the provided water dispenser, use
the two fittings supplied with your Direct Connect Faucet Kit.

1. A stainless female thread x push connector (Connects to the water supply valve then to filter
housing inlet)
2. A brass 3/8” male compression fitting x push connector. (Connects to the cold water faucet to
filter housing outlet)
Step 4 - Install the Accessory Water Dispenser
1. Select a suitable location for the accessory water dispenser as close to the sink as possible
allowing convenient space under the sink for assembly. If not using the extra sink hole, drill the
sink top with a 1/2” bit to accommodate the inlet pipe.
2. Assemble the water dispenser to the sink top:
a. Insert the valve through the sink top with the rubber washer underneath the chrome plate on
top of the sink surface.
c. Thread lock washer and brass/plastic nut onto the thread assembly underneath the sink and
tighten by hand and if necessary, carefully with a wrench.
d. Attach the push-fit faucet connector directly onto the metal pipe end.
Step 5 - Install Connecting Tube
1. Cut two pieces of the 3/8” plastic tubing to fit from the water supply to the inlet of the filter
housing and from the outlet of the filter to the water dispenser.
A. Tubing from water supply to filter housing inlet:
a. Insert one end of tubing into the outlet push connector of the tee fitting.
(seat completely into push connector fitting), and insert lock clip.
b. Insert other end of tubing into inlet push connector of filter housing.
(seat completely into push connector fitting), and insert lock clip.
B. Tubing from filter outlet on top of the housing to the water dispenser.
a. Both ends of tubing are to be inserted into the push connectors.

b. Insert blue lock clips onto the sleeve of all push connectors.
Step 7- Start-Up
1. Open the tap fully by lifting the lever to its vertical position to allow trapped air and water to
flow out of the system.
2. Turn water on at the main inlet of the cold water supply. Water should start flowing out of the
faucet once housing has filled with water.
4. Once water begins to flow out of the faucet after air is expelled, turn o!water flow and let
stand for 20 minutes. Turn water flow back on and flush the system for a five minutes to allow
residual particles to be expelled during this first flush; this is normal. The system is now ready
for use. Taste will improve once filters are completely flushed of residual particles.
6. As water passes through the new filters, tiny oxygen bubbles may appear causing your water
to appear white or murky. This is normal and harmless and will disappear after a few days of
use.
6. For a 24 hour period after installation, periodically check your unit to ensure there are no
leaks.
Optional - Secure the bracket and head assembly to the side of the sink cabinet in the desired
location with the two (2) small mounting screws.
Troubleshooting
1. No flow of water through the system: Check the plastic tubing for kinks, or obstructions.
2. Water leaks:
a. At the push fittings: inspect to be sure tubing has been fully sealed.
b. At the tee connector: ensure all fittings are tight.
c. At the housing: verify that the housing has been fully tightened.
Rated Service Flows For Filters: 1 gpm or less for optimal filtration.
Maximum Working Pressure: (125 psig) Maximum Working Temperature: 38° C (100° F)
Minimum Operating Pressure: (10 psig) Minimum Operating Temperature: 5° C (41° F)

Cleaning and Maintenance Sanitizing Your Filter Housing
1. Your under sink filter can be sanitized yearly for two consecutive years. Remove the filter
from the housing and place the filter in direct sunlight for 48 hours and then insert back into the
housing and reattach to the bracket.
For Support Call 208-462-0626