Greenlee ES750 User manual

99926288 © 2011 Greenlee Textron Inc. IM 1322 REV 9 1/11
INSTRUCTION MANUAL
ES750
Battery-powered Cable Cutter
45380—with 120 V Charger
45381—with 220 V Charger
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
Register this product at www.greenlee.com

2
KEEP THIS MANUAL
Table of Contents
Description, Safety, and Purpose of this Manual ................................................................ 2
Important Safety Information........................................................................................... 3–7
Specications...................................................................................................................... 8
Operation............................................................................................................................. 9
Charger.............................................................................................................................. 10
Troubleshooting................................................................................................................. 11
Maintenance...................................................................................................................... 12
Illustration.......................................................................................................................... 13
Parts List ..................................................................................................................... 14–15
Description
The Greenlee Battery-powered Cable Cutter is intended to cut up to 750 kcmil copper
and aluminum cable. The cable cutter is driven by a 12-volt motor and is powered by a
rechargeable NiCd (nickel cadmium) battery. The motor is protected by a circuit breaker.
Safety
Safety is essential in the use and maintenance of Greenlee tools and equipment.
This manual and any markings on the tool provide information for avoiding hazards and
unsafe practices related to the use of this tool. Observe all of the safety information
provided.
Purpose of this Manual
This manual is intended to familiarize all personnel with the safe operation and
maintenance procedures for the Greenlee ES750 Battery-powered Cable Cutter.
Keep this manual available to all personnel.
Replacement manuals are available upon request at no charge at www.greenlee.com.
All specications are nominal and may change as design improvements occur.
Greenlee Textron Inc. shall not be liable for damages resulting from misapplication
or misuse of its products.
Do not discard this product or throw away!
For recycling information, go to www.greenlee.com.

3
ES750
IMPORTANT SAFETY INFORMATION
SAFETY ALERT SYMBOL
This symbol is used to call your attention to hazards or unsafe practices which could
result in an injury or property damage. The signal word, dened below, indicates the
severity of the hazard. The message after the signal word provides information for
preventing or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result in severe injury or death.
Hazards which, if not avoided, COULD result in severe injury or death.
Hazards or unsafe practices which, if not avoided, MAY result in injury or property
damage.
Read and understand all of the instructions and safety information in
this manual before operating or servicing this tool.
Failure to observe this warning could result in severe injury or death.

4
IMPORTANT SAFETY INFORMATION
Cable Cutter
Electric shock hazard:
This tool is not insulated. When using this unit near energized electrical
lines, use proper personal protective equipment.
Failure to observe this warning could result in severe injury or death.
Wear eye protection when operating or servicing this tool.
Failure to wear eye protection could result in serious eye injury from
ying debris.
• Keephandsawayfromblade.
• Removethebatterybeforeinspectingorservicingthetool.
Failure to observe these warnings could result in severe injury or death.
• Usethistoolformanufacturer’sintendeduseonly.Useotherthanthatwhichis
described in this manual can result in injury or property damage.
• DonotcutsteelorACSR.
• Inspectthetoolbeforeeachuse.Replaceanyworn,damaged,ormissingitemswith
Greenlee replacement parts. A damaged or improperly assembled tool can break and
strike nearby personnel.
Failure to observe these precautions may result in injury or property damage.

5
ES750
Battery
IMPORTANT SAFETY INFORMATION
Do not dispose of battery in a re. The battery will vent harmful vapors and
can explode.
Failure to observe this warning could result in severe injury or death.
Do not allow any object to contact the battery terminals.
• Donotimmersebatteriesinliquid.Liquidmaycreateashortcircuitanddamagethe
battery.
• Donotplacethebatteryintoapocket,toolpouch,ortoolboxwithconductive
objects. Conductive objects may create a short circuit and damage the battery.
• Donotplaceabatteryonmoistgroundorgrass.Moisturemaycreateashortcircuit
and damage the battery.
Failure to observe these precautions may result in injury or property damage.
• Donotchargethebatteryifitiscoolerthan50°F(10°C)orwarmerthan
95°F(35°C).Damagetothebatterycanresult.
• Donotstorethebatteryatmorethan140°F(60°C).Damagetothebatterycanresult.
• Donotuseanothermanufacturer’scharger.Othermanufacturers’chargersmay
overcharge and damage the battery.
Failure to observe these precautions may result in injury or property damage.
• Donotexposethebatterytoliquidssuchaswater,oil,orsolvents.Liquidswill
damage the battery.
• Donotattempttoopenthebattery.Itcontainsnouser-serviceableparts.
• Usethisbatteryformanufacturer’sintendeduseonly.Useotherthanthatwhichis
described in this manual can result in injury or property damage.
• Inspectthebatterybeforeeachuse.Donotuseadamagedbattery.
Failure to observe these precautions may result in injury or property damage.

6
IMPORTANT SAFETY INFORMATION
Charger
Electric shock hazard:
• Useindoorsonly.
• Donotexposethechargertorain,snow,orwetconditions.
• Unplugthechargerfromthepowersourcebeforecleaningthe
charger.
Failure to observe these warnings could result in severe injury or death.
Greenlee recommends plugging the charger directly into a receptacle. If an extension
cord must be used:
• Selectanextensioncordwithacongurationthatexactlymatchesthatofthe
charger’splug.
• Inspecttheextensioncordforwearordamage.
Use of an improper or damaged extension cord could result in electric shock or re.
• Donotobstructtheventilationslots.Thisdevicegeneratesheatwhilecharging.
Excessive internal heat can result in a re.
• Donotuseorstorethechargernearaheatsource.Thisdevicegeneratesheatwhile
charging. Excessive internal heat can result in a re.
Failure to observe these warnings could result in severe injury or death.

7
ES750
IMPORTANT SAFETY INFORMATION
Charger (cont’d)
Use this charger to charge the supplied 12-volt rechargeable NiCd (nickel cadmium)
batteries only. Other batteries may burst if charged with this charger.
Failure to observe this warning could result in severe injury or death.
Do not place anything other than the supplied 12-volt rechargeable NiCd (nickel
cadmium) battery into the battery pocket.
• Keepdirtandforeignobjectsoutofthebatterypocket.
• Donotcreateashortcircuitacrossthecontactsinthebatterypocket.
Failure to observe this precaution may result in injury or property damage.
• Donotconnectthechargertoagenerator.Voltageuctuationscandamagethe
charger.
• Inspectthechargerbeforeeachuse.Replacetheunitifeitherthechargerorcord
show signs of damage or wear.
• Donotattempttorepairthecharger.Itcontainsnouser-serviceableparts.
• Usethistoolformanufacturer’sintendeduseonly.Useotherthanthatwhichis
described in this manual can result in injury or property damage.
Failure to observe these precautions may result in injury or property damage.

8
Specifications
Cutter
Weight (with battery)............................................................................................5 lb, 8 oz
Weight (with battery, charger, and case) ...........................................................9 lb, 10 oz
Height.................................................................................................................... 13-5/8"
Width ....................................................................................................................... 6-1/2"
Depth....................................................................................................................... 4-1/8"
Wire Type.......................................................................................... Copper or aluminum
Maximum Wire Size............................................................................................750 kcmil
Motor.....................................................................................................................12 VDC
Battery
Type .................................................................................. Rechargeable nickel-cadmium
Voltage........................................................................................................................ 12 V
Charger
Voltage.............................................................................................. 120 VAC or 220 VAC
Trigger
RESET
(yellow button)

9
ES750
Operation
1. Slide the direction control lever to select either FORWARD or REVERSE. Press the
switch to activate the cable cutter. Release the switch after the movable blade is
disengaged from the driver.
2. Place the cable to be cut against the stationary blade until it is engaged by the driver.
Close the movable blade around the cable.
3. Slide the direction control lever to FORWARD. Press the switch. After the cable is
completely cut, release the switch.
4. Slide the direction control lever to the center (LOCK) position.
Circuit Breaker
The following may cause the circuit breaker to trip:
• Cuttingmaterialthatistoolarge
• Cuttingmaterialthatistoohard
• Overheatingduetocontinuoususe
• Drawingexcessivecurrent
If the circuit breaker trips, the tool will stop. If necessary, allow the tool to cool down.
Press the RESET button. (Wait 10 seconds to 1 minute before resetting.)
Do not cut steel or ACSR.
REVERSE
Driver
Fixed Blade
Movable Blade
FORWARD
LOCK

10
Charger
The battery charger will recharge the battery in approximately one hour.
Do not connect the charger to a generator. Voltage uctuations may damage
the charger.
1. Setthechargeronarmlevelsurfaceoutofdirectsunlight.Besurethatthecharger’s
ventilation slots are not blocked.
2. Connect the charger to an appropriate power supply.
3. Insert the battery into the battery pocket of the charger. The LED will light to indicate
that the battery is charging. After approximately one hour, the LED will turn off to
indicate that the battery is fully charged.
4. Remove the battery from the charger.
Note: Allow the charger to cool for at least 15 minutes before charging another battery.