Greentouch Scott Living 1267FM-28-201 Quickspecs

Wall/Corner Media Fireplace
with 28-IN Infrared Electric
Insert
ASSEMBLY, CARE & USE INSTRUCTIONS
MODEL # 1267FM-28-201
ITEM # 1068262
Date Purchased _______________________
Questions, problems, missing parts?
Before returning to your retailer,
call our customer service department at
1-855-571-1044 9 a.m. - 5 p.m., EST, Monday - Friday.
www.greentouchhome.com
Français p. 17
Español p. 33

2
PACKAGE CONTENTS
A
B
C
D
E
F
I
J
K
L
H
G
M
PART DESCRIPTION QUANTITY
ATop 1
B Corner Panel 1
C Left Wall 1
D Right Wall 1
E Left Front Panel 1
F Right Front Panel 1
G Center Panel 1
H Wood Door Panel 1
I L Corner Support Rod 1
J Base 1
PART DESCRIPTION QUANTITY
K Insert 1
L Remote Control 1
M Battery 2

3
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
AA BB CC DD
PART DESCRIPTION QUANTITY
AA Long Bolt 25
BB Washer 25
CC Wooden Dowel 18
DD Touch-up Pen 1

4
SAFETY INFORMATION
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock and injury to persons, including the
following:
DANGER
• Read all instructions before using this heater.
• If the information in this manual is not followed
exactly, an electric shock or fire may result causing
property damage, personal injury or loss of life.
• This product is intended to fit most plasma and
LCD televisions (up to 56 inches and weighing a
maximum of 80 pounds). Using this item with loads
heavier than the stated maximum can result in
tipping and/or instability, which can result in injury or
even death.
WARNING
• This appliance is hot when in use. To avoid burns,
DO NOT let bare skin touch hot surfaces. Keep
combustible material, such as furniture, pillows,
bedding, papers, clothes and curtains at least 3 feet
from this appliance and keep them away from the
sides and rear.
• Extreme caution is necessary when any heater
is used by or near children or individuals with
disabilities and whenever the fireplace is left
operating and unattended.
• DO NOT run cord under carpeting. DO NOT cover
cord with throw rugs, runners, or similar coverings.
DO NOT route cord under funiture or appliances.
Arrange cord away from traffic areas and where it
will not be tripped over.
• DO NOT insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the appliance.
• This appliance has hot and arcing or sparking parts
inside. DO NOT use it in areas where gasoline,
paint or flammable vapors or liquids are used or
stored. This fireplace should not be used as a
drying rack for clothing. Christmas stockings or
decorations should not be hung in the area of it.
• Use this appliance only as described in the manual.
Any other use is NOT recommended by the
manufacturer and may cause fire, electric shock or
injury to persons.
CAUTION
• If possible, ALWAYS unplug this appliance when
not in use.
• DO NOT operate any heater with a damaged
cord or plug or after the heater malfunctions. DO
NOT operate any heater if it has been dropped
or damaged in any manner. Disconnect power
at service panel and have heater inspected by a
reputable electrician before reusing.
• Any repairs to this fireplace should be carried out
by a qualified service person.
• Under no circumstances should this fireplace be
modified. Parts having to be removed for servicing
must be replaced prior to operating this fireplace
again.
• DO NOT use outdoors.
• This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. NEVER
place heater where it may fall into a bathtub or
other water container.
• To disconnect this appliance, turn controls to the off
position, then remove plug from outlet.
• ONLY connect to properly grounded outlets.
• This appliance, when installed, must be electrically
grounded in accordance with local codes, with the
current CSA C22.1 Canadian Electrical Code or
follow U.S.A. Installations, follow local codes and
the National Electrical Code, ANSI/NFPA N0.70.

5
SAFETY INFORMATION (CONT'D)
• To prevent a possible fire, DO NOT block air intakes
or exhaust in any manner. DO NOT use on soft
surfaces, like a bed, where opening may become
blocked.
• The heaters MUST NOT be located immediately
below a socket-outlet.
• ALWAYS plug heaters directly into a wall outlet /
receptacle. NEVER use with an extension cord or
re-loadable power tap (outlet / power strip).
• DO NOT slide insert on top of wood to avoid
scratching wood surface.
• DO NOT place any object on top of the insert or
block the air intakes / vents as this can cause the
unit to overheat and could cause a fire.
Electrical Connection
• A 15-Amp, 120-volt, 60 Hz circuit with a properly
grounded outlet is required. Preferably, the fireplace
will be on a dedicated circuit as other appliances
on the same circuit may cause the circuit breaker
to trip or the fuse to blow when the heater is in
operation. The unit comes standard with 6-ft. three-
wire cord, exiting from the rear of the fireplace. DO
NOT exceed the current rating of the current tap.
Grounding Instructions
• This heater is for use on 120 volt.The cord has a
plug as shown below. See illustration or grounding
instruction. An adapter as shown at C is available
for connecting three-blade grounding type plugs
to two-slot receptacles. The green grounding plug
extending from the adapter must be connected to
a permanent ground such as a properly grounded
outlet box. The adapter should not be used if a
three-slot grounded receptacle is available.
SAVE THESE INSTRUCTIONS
A B C
Grounding Pin
Grounding Means
Metal
Screw
Cover of
Grounding
Box
Adapter

6
PREPARATION
Before beginning assembly of product, make
sure all parts are present. Compare parts with
package contents list and hardware contents list.
If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Assembly Time: 50 minutes
Tools Required for Assembly (not included):
Phillips screwdriver
ASSEMBLY INSTRUCTIONS
1. From behind the assembly, align the holes on
left front panel (E) with the corresponding holes
on left wall (C). securing with two washers (BB)
and two long bolts (AA).
Repeat for right wall (D)
Hardware Used
AA Long Bolt x 4
BB Washer x 4
1
F
D
E
C
BB AA
2. Insert four wooden dowels (CC) into holes on left
outer side of base (J). Place assembly from Step
1 onto base (J), securing with three washers
(BB) and three long bolts (AA).
Repeat for right wall (D).
Hardware Used
AA Long Bolt x 6
BB Washer x 6
CC Wooden Dowel x 8
J
CC
BB
AA
1
1
2
2

7
ASSEMBLY INSTRUCTIONS (CONT’D)
3. Insert two wooden dowels (CC) into the top
middle holes on both left front panel (E) and right
front panel (F). Carefully position the center
panel (G) into place between left front panel (E)
and right front panel (F). Secure each side with
one washer (BB) and one long bolt (AA).
Hardware Used
AA Long Bolt x 2
BB Washer x 2
CC Wooden Dowel x 2
G
CC
AA
BB
1
3
2
4. Insert two wooden dowels (CC) into the top
outer holes on both left wall (C) and right wall
(D). Attach top (A), securing from underneath
with seven washers (BB) and seven long bolts
(AA).
Hardware Used
AA Long Bolt x 7
BB Washer x 7
CC Wooden Dowel x 4
A
CC
BB
AA
1
4
2
5. From behind the assembly, remove the
preassembled insert brackets from the opening area.
Save brackets and screws for future use.
2
2
5
1

8
ASSEMBLY INSTRUCTIONS (CONT’D)
Note: Before proceeding to the next step, with
the help of another person, move the mantel
close to the final desired location.
6. With the help of another person, position insert
(K) into middle opening of mantel assembly.
Note: DO NOT plug insert (K) into power outlet
yet.
CAUTION: DO NOT slide insert on top of wood
to avoid scratching wood surface.
K
6
7. Re-attach insert brackets with previously
removed screws to secure insert (K).
Assembly is now complete. With the help of
another person, move the assembly to the final
desired location. Once in final position you may
plug the insert (K) into the power outlet.
1
1
K
7
2
CORNER ASSEMBLY (OPTIONAL)
1. From behind the assembly, Attach L corner
support rod (I), secure with one washer (BB) and
one bolt (AA).
Hardware Used
AA Long Bolt x 1
BB Washer x 1
I
BB
AA
1

9
CORNER ASSEMBLY (CONT’D)
2. Insert four wooden dowels (CC) into the top
back holes of mantel, Attach corner panel (B),
secure with five washers (BB) and five long bolts
(AA).
Assembly is now complete. With the help of
another person, move the assembly to the final
desired location. Once in final position you may
plug the insert (K) into the power outlet.
Hardware Used
AA Long Bolt x 5
BB Washer x 5
CC Wooden Dowel x 4
B
CC
BB
AA
2
NOTE: Use the pre-assembled levelers on the
base of the fireplace to level the unit. Twist the
levelers counter clockwise to increase the height,
twist the clockwise to decrease the height.

10
CHANGE DOOR PANELS (OPTIONAL)
Note: The pre-installed glass door panels can be switched out with the included wood door panel (H).
1. Remove the silicone trim along the outer edges of the glass panel on the inside of the flip down
door. Start at a corner and pull to remove the four pieces. Be careful not to damage the silicone
trim as it will be used to secure the new panel.
2. Remove the glass panel from the door frame, then insert the included wood door panel (H).
3. Using your finger press the silicone trim back into place. Move around the outer edge of the panel
until all four sides are secure.
H
2
1
1
4
3
2
3
1
2
3
4

11
OPERATING INSTRUCTIONS
Control Panel
M
Remote Control
AAA 1.5V
AAA 1.5V
To use the remote control,
first insert two AAA batteries
(included) into the remote control.
Ensure the polarities of the
battery match the inside of the
battery compartment.
Note: The control panel is a touch screen. It will appear black. Touch the control panel once to “wake up” the
controls. This will cause the controls to light up. Which ever icon you touch will display it’s last setting when
you do this. At this time you can press the corresponding icon to the function you would like to adjust. After 5
seconds the touch screen will fade to black.
M
Power Function
• Press the POWER ICON to turn the main power to the unit ON or OFF.
• When the unit is powered ON, the lights under the emberbed will glow to indicate the unit has
power.
• If any functions are stored in memory then they will resume at the last setting.
Flame Brightness Function
• Press the FLAME BRIGHTNESS ICON to adjust the flame brightness.
• If the unit main power is OFF, you can press the FLAME BRIGHTNESS ICON to power ON the unit
and flame brightness will resume at the last setting.
• Press the FLAME BRIGHTNESS ICON again to scroll up through the flame brightness settings: 1, 2,
3, 4, 5, OF.
Temperature Function
• If the unit is powered OFF, you can press the TEMPERATURE ICON to power ON the unit. The
emberbed will glow at the lowest brightness setting unless a different setting was saved in the
memory.
• Press and hold the TIMER ICON for 5 seconds to toggle between 5°F (3°C) increments and 1ºF
(1°C) increments when setting the temperature. The factory default temperature is 5°F (3°C)
increments.
Note: This option is only available if using the control panel.
• Hold down the TEMPERATURE ICON for 5 seconds to toggle between Fahrenheit and Celsius. An
“F” or “C” will display next to the temperature.
Note: This option is only available if using the control panel.
• Press and hold the TEMPERATURE ICON for 10 seconds to disengage the heater function. Press
and hold the TEMPERATURE ICON for 10 seconds again to engage the heater function. (See
HEATER OVERRIDE section below for more details).
Increase/Decrease Button
Note: This option is only available if using the remote control.
• Press the INCREASE/DECREASE button to adjust the heater’s thermostat setting.
• Press the INCREASE/DECREASE button again to scroll up through the pre-set temperature
settings: The thermostat setting range is 65°F (18°C) to 90ºF (32°C), HI (High).
• Set the temperature to “HI” to have the heater run continually.

12
OPERATING INSTRUCTIONS (CONT’D)
Timer Function
• Press the TIMER ICON to set the countdown for the unit’s main power.
• If the unit is powered OFF, you can press the TIMER ICON to power ON the unit. The emberbed
will glow at the lowest brightness setting unless a different setting was saved in the memory.
• Press the TIMER ICON again to scroll through the timer settings, which are: 30, 1H, 2H, 3H, 4H,
5H, 6H, 7H, 8H, 9H, OF. (30 means 30 minutes, OF means OFF)
• When the timer reaches zero, it will turn OFF the main power and will maintain all the settings in
memory.
HEATER OVERRIDE
The power to the heater can be disengaged to prevent the heater from being accidentally or unintentionally
powering on. This feature is primarily added to help prevent children from powering on the heater when it is
not desired.
• To engage the heater override function press and hold the TEMPERATURE ICON for 10 seconds. The
symbol E3 will display. The heater function is now locked. If the TEMPERATURE ICON is pressed again E3
will appear then fade.The Flame and Timer functions will operate normally. Only the heater and blower are
disengaged.
• To unlock the heater function, press and hold the TEMPERATURE ICON for 10 seconds. The symbol E3 will
display. The heater function is now engaged. By pressing the TEMPERATURE ICON again you will be able
to adjust the heat temperature to your desired temperature.
MEMORY FUNCTION
This unit has a memory function that allows you to turn off the MAIN POWER and retains all the other function
settings (excluding the TIMER function).
• When the unit’s main power is OFF, press the POWER ICON once on the insert control panel or on the
remote control to power the unit ON and “wake up” the individual function at the last setting. Press the icon
again to adjust it and press the main POWER ICON on the insert or on the remote control to turn the unit
OFF and save the new setting into memory.
• When the unit is powered ON, the LED readout will show the saved temperature setting. If a temperature
setting was not saved, it will show the flame brightness setting saved in memory. If neither one has a setting
saved to memory, then only the emberbed will glow (as a power light indicator).
• To reset the memory, hold down the main POWER ICON for 10 seconds at any time. When this happens,
the LED readout will blink with two zeros three times and the unit will be shut down.
• Another way to reset the memory is to unplug the unit from the wall.

13
CARE AND MAINTENANCE
• Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool whenever you are
cleaning the heater or fireplace.
• Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or household
cleaners as these products will damage the metal trim.
• The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life
and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and air intake/
output vents is recommended.
• When the heater is not in use, the power cord should be stored properly to avoid contact with hot or sharp
objects.
• Any other servicing should be performed by an authorized service representative.
Replacing the Remote Control Batteries
When the remote control (L) stops operating or its range
seems reduced, it is time to replace the batteries. Note:
The batteries should be removed if the product is to be left
unused for a long time.
1. The battery compartment is located on the back of the
remote control (L).
2. Remove battery cover from the back of remote control (L)
and remove old batteries.
3. Insert 2pcs AAA batteries, ensuring the polarities of the
battery match the inside of the battery compartment.
4. Re-insert the battery door.
AAA 1.5V
AAA 1.5V
L
Note: Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc), or rechargeable (nicad, nimh, etc) batteries.
Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from the
product.
Harmful if swallowed.
Disposal of Used Battery
A battery may contain hazardous substances that could be endangering the environment and human health.
• This symbol marked on the battery and/or packaging indicates that used
battery shall not be treated as municipal waste. Instead it shall be left at
the appropriate collection point for recycling.
• By ensuring the used battery is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health. The recycling of materials will help to conserve natural resources.
• Do not dispose of batteries in fire. Batteries may explode or leak.
For more information about collection and recycling of used batteries,
please contact your local municipality, your waste disposal service or the
point-of-sale where you purchased this battery.

14
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Error E1 displayed on
control panel.
The overheat sensor has
been engaged.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding
the heater. Until the problem is solved, the error will only
appear/sound when the heater button is pressed.
Error E2 displayed on
control panel.
The thermostat sensor
is broken or not working
correctly.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding
the heater. Until the problem is solved, the error will only
appear/sound when the heater button is pressed.
Error E3 displayed on
control panel.
Heater override function is
engaged
To unlock the heater, simply press and hold the temperature
button for 10 seconds (See page 12 Heater Override
Section for more details).
No power; logs do not
glow.
The unit does not have
power.
Check that the power cord is securely plugged into a
standard 120V outlet. Then check to make sure the unit is
powered on.
No flame effect but
logs are glowing.
The flame effect is
powered off.
Push the flame brightness button until desired level is
achieved.
Heater and blower
do not power on but
rest of functions are
working.
Heater override function is
engaged
To unlock the heater, simply press and hold the temperature
button for 10 seconds (See page 12 Heater Override
Section for more details).
Power cord gets warm
to the touch.
Normal operation. This is normal for a heater appliance as it requires more
current to operate. Check the connections of the appliance
cord and the outlet. Make sure the plug fits tightly into the
outlet. During use, check the plug and outlet frequently to
determine if it is HOT; if so, discontinue use of the appliance
and consult with a qualified electrician to check or change
the overheating outlet(s).
Remote control does
not work.
Weak or failing batteries. Replace with 2 AAA batteries (See page 13 for more
information.)
Remote control signal
is weak and only
works sometimes.
Pressing the buttons too
quickly.
Press the buttons slowly and steadily to ensure the
transmitter recognizes the request.
Using the remote control
too far away or at an off
angle.
Move closer to the insert; the remote control will only work
within a distance of 20 feet and 45 degrees to either side
from the front of the fireplace insert.
Fan motor continues
to blow after unit is
powered off.
Normal operation. This is a standard feature; the blower runs for an additional
time to cool off heater tubes.

15
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants that your new Electric fireplace is free from manufacturing and material
defects for a period of one year from date of purchase, subject to the following conditions and
limitations.
Install and operate this Electric fireplace in accordance with the installation and operating instructions
furnished with the product at all times. Any unauthorized repair, alteration, willful abuse, accident, or
misuse of the product shall nullify this warranty.
This warranty is non-transferable, and is made to the original owner, provided that the purchase was
made through an authorized supplier of the product.
The warranty is limited to the repair or replacement of part(s) found to be defective in material or
workmanship, provided that such part(s) have been subjected to normal conditions of use and service,
after said defect is confirmed by the manufacturer’s inspection.
The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by
refunding the wholesale price of the defective part(s).
Any installation, labor, construction, transportation, or other related costs/expenses arising from
defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor
shall the manufacturer assume responsibility for same.
The owner/user assumes all other risks, if any, including the risk of any direct, indirect or consequential
loss or damage arising out of the use, or inability to use the product, except as provided by law.
All other warranties-expressed or implied-with respect to the product, its components and accessories,
or any obligations/liabilities on the part of the manufacturer are hereby expressly excluded.
The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other
liabilities with respect to the sale of the product.
The warranties as outlined within this document do not apply to non accessories used in conjunction
with the installation of this product.
This warranty is void if:
1.The fireplace is subjected to prolonged periods of dampness or condensation.
2.Any unauthorized alteration, willful abuse, accident, or misuse of the product.
3.You do not have the original receipt of purchase.

16
REPLACEMENT PARTS
For replacement parts, call our customer service department at 1-855-571-1044, 9 a.m. - 5 p.m., EST,
Monday - Friday.
E
L
K
F
G
Q
H
A
HH II JJ LL KK MM NN
PART DESCRIPTION PART #
ATop 1267FM-28-201-TOP
E
Insert surround set PF-1267FM-28-201-
CARRARA
F
G
HFlip-down door center
panels
PH-1267FM-28-201-
CENTER PANELS
Q
K Insert 2822-FG-C5
L Remote Control PU18-33CB-RC
HH KD Hardware pack PH-1267FM-28-201
II Flip-down door
hardware set PU17-1267FM-II/JJ/LLJJ
LL
KK Flip-down door handle PU17-1267FM-HANDLE
MM Leveler T-1007
NN Insert Bracket INSERT-STONE SIDE-MB

Cheminée multimédia murale /
d’angle avec foyer électrique
encastrable infrarouge de 28 po
INSTRUCTIONS D’UTILISATION, D’ASSEMBLAGE
ET DE MAINTENANCE
MODÈLE # 1267FM-28-201
ARTICLE # 1068262
Date d’achat _______________________
Des questions, des problèmes, des pièces manquantes?
Avant de retourner l’article au détaillant,
appelez notre service à la clientèle au
1-855-571-1044, entre 9 h et 17 h (HNE), du lundi au vendredi.
www.greentouchhome.com
English p. 1
Español p. 33

18
CONTENU DE L’EMBALLAGE
A
B
C
D
E
F
I
J
K
L
H
G
M
PIÈCE DESCRIPTION QUANTITÉ
A Dessus 1
B Panneau de coin 1
C Cloison gauche 1
D Cloison droite 1
E Panneau avant gauche 1
F Panneau avant droit 1
G Panneau central 1
H Panneau de porte en bois 1
ITige de support de coin en L 1
J Base 1
PIÈCE DESCRIPTION QUANTITÉ
K Foyer encastrable 1
L Télécommande 1
M Pile 2

19
CONTENUS MATÉRIELS (NON REPRÉSENTÉS EN TAILLE RÉELLE)
AA BB CC DD
PIÈCE DESCRIPTION QUANTITÉ
AA Boulon long 25
BB Rondelle 25
CC Groujon en bois 18
DD Crayon à retouche 1

20
CONSIGNES DE SÉCURITÉ
CONSIGNES IMPORTANTES
Lorsque vous utilisez un appareil électrique, respectez
les mesures de sécurité élémentaires suivantes afin
de réduire les risques d’incendie, de choc électrique
et de blessure :
DANGER
• Lisez toutes les instructions avant d'utiliser cet
appareil de chauffage.
• Respectez scrupuleusement les directives du
présent manuel pour prévenir les chocs électriques
ou les incendies pouvant causer des dommages
ainsi que des blessures graves ou mortelles.
• Cet article a été conçu pour accueillir la plupart des
téléviseurs à écran plasma et ACL (jusqu’à 56 po
et d’un poids maximal de 36.36 kg). Le fait d’utiliser
cet appareil avec des produits dont le poids excède
la charge maximale indiquée peut entraîner un
basculement ou de l’instabilité et causer des
blessures ou même la mort.
AVERTISSEMENT
• Cet appareil est chaud lorsqu’il est en fonction.
Afin d’éviter les brûlures, ne touchez PAS aux
surfaces chaudes. Assurez-vous que les matières
combustibles, comme les meubles, les oreillers, la
literie, le papier, les vêtements et les rideaux, se
trouvent à au moins 0,91 m de l’appareil.
• Faites preuve d’une extrême prudence lorsqu’un
radiateur est utilisé à proximité d’enfants ou de
personnes handicapées, de même que lorsque
vous laissez le foyer en marche sans surveillance.
• Ne placez PAS le cordon sous un tapis. Ne couvrez
PAS le cordon d’alimentation avec une carpette, un
tapis de couloir, ni tout autre article similaire. Placez
le cordon dans un endroit peu passant et où il ne
pourra pas être accroché.
• N’insérez JAMAIS un objet, quel qu’il soit, dans
les ouvertures de ventilation ou de sortie d’air de
l’appareil afin de prévenir les dommages ainsi que
les risques de choc électrique et d’incendie.
• Cet appareil renferme des pièces chaudes qui
produisent des arcs électriques ou des étincelles.
N’utilisez PAS l’appareil là où de l’essence, de la
peinture, de la vapeur ou des liquides inflammables
sont utilisés ou entreposés. Ce foyer ne doit
pas être utilisé pour faire sécher les vêtements.
Ne suspendez PAS de bas de Noël ou d’autres
décorations à proximité du foyer.
• N’utilisez cet appareil que pour l’usage prévu
dans ce manuel. Toute autre utilisation n’est PAS
recommandée par le fabricant et peut provoquer un
incendie, un choc électrique ou des blessures.
ATTENTION
• Dans la mesure du possible, débranchez
TOUJOURS cet appareil lorsqu’il n’est pas utilisé.
• N’utilisez PAS un appareil muni d’une fiche ou d’un
cordon endommagés ou qui a subi une défaillance.
Ne faites PAS fonctionner un appareil qui est tombé
ou qui a été endommagé de quelque façon que ce
soit. Coupez l’alimentation électrique à partir du
tableau de distribution et faites inspecter l’appareil
par un électricien qualifié avant de le réutiliser.
• Confiez toute réparation de ce foyer à un technicien
qualifié.
• Ne modifiez jamais ce foyer. Replacez les pièces
qui ont dû être retirées pour l’entretien avant
d’utiliser de nouveau le foyer.
• N’utilisez PAS cet article à l’extérieur.
• Cet appareil n’est pas conçu pour être utilisé
dans une salle de bains, une salle de lavage ou
tout autre endroit humide semblable. Ne placez
JAMAIS l’article dans un endroit où il pourrait
tomber dans une baignoire ou un autre contenant
rempli d’eau.
• Pour débrancher cet appareil, tournez les
commandes en position d’arrêt, puis retirez la fiche
de la prise.