GreenWorks 51017 User manual

120 Bar / 340 L/H

The cleaner is intended only for the cleaning of vehicles,
boats,buildings,etc,by the removal of stubborn dirt using
clean water and chemical detergents.
For domestic use only,not for professional use,and only
for operation at temperature above 0°C
INTENDED USE
ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

greenworks Tools
Fig.1
( )
ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

Rated Voltage
Rated Pressure
Permissible Pressure
Power Rating
Maximum Water Flow
Maximum Water Inlet Pressure
Maximum Water Inlet Temperature
Maximum Water Temperature
LWA(sound power level)
LPA(sound pressure level)
Protection Degree
Vibration
..........................................................................................................
.......................................................................................................................
.................................................................................................................
...........................................................................................................................
...............................................................................................................
...................................................................................................
.................................................................................................
.........................................................................................................
............................................................................................
........................................................................................................................
..................................................................................................................
220-240V ~ 50 Hz
9.5 MPa
12 MPa
1600W
Rated Water Flow .............................................................................................................................................. 4.5 l/lim
5.6 l/min
0.7 MPa
40°C
94 dB(A)
82 dB(A) K=3dB(A)
IPX5
4.0 m/s² K=1.5 m/s²
9. High pressure
hose
10. Spray wand 11. Gun
8. Detergent tank
Fig. 2
keep the extension cord clesr of the working area. Position the cord so that it will not get caught on lumber,
tools or other obstructions while you are working with a power tool. Failure to do so can result in serious
personal injury.
2. Gun storage hook
1. On/Off switch
6. Wheels
4. Electric cord storage hook
7. Electric cord hook
5.Water intake
3. Handle assembly
ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

Remove the nozzle from the detergent tank and pour the
detergent into tank
If in doubt,call Greenworks Tools Customer Service for
assistance Operation of a product that may have been
improperly preassembled could result in serious
personal injury.
ASSEMBLING WAND TO WASHER GUN.
Installing Wand to Pressure Washer Gun
Insert the male baynet end(1) of the wand into the
female bayonet outlet(3) firmly.While pushing in the
wand firmly,turn clockwise(2) until tabs lock into place
to ensure a leak-free connection.
Fig.4
Fig.3
Fig. 5
Greenworks Tools
(See Figure 4.)
(See Figure 5.)
(See Figure 3.)
ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

Fig.6
NOTE: Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If
any detergent is spilled during the filling process,
make sure the unit is cleaned and dried before
proceeding.
NOTE:Use a funnel, if needed, to prevent accidental
spilling of the detergent outside the tank. If any detergent
is spilled during the filling process,make sure the unit is
cleaned and dried before proceeding.
(See Figure 6.)
120
EN 60335-2-79:2009
ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly.Check to see that the nozzle is secure.
Fig. 7
Install the detergent bottle on the spray wand
(See Figure 7.)
ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

Fig.8
(See Figure 8.) Fig.10
Telescopic handle use: (See Figure 10.)
Pull up and fully extend handle for use.
For transporting, pull as shown.
To lower handle; push handle until it lock into place
for storage.


I M P O R T A N T
This handle is for pulling the unit.Do not lift the unit by
this handle.
ENGLISH(Original Instructions)
FR DE
EN
ES IT PT SV DA NO FI RU PL

ENGLISH(Original Instructions)
PROBLEM
Motor will not start.
Unit does not reach
high pressure.
Output pressure varies
high and low.
POSSIBLE CAUSE
On/O ff switch is in the
“OFF” (O) position.
Power cord is not plugged in.
Defective extension cable.
Electrical outlet does not supply
adequate power.
Diameter of garden hose is
too small.
Water supply is restricted.
Not enough water supply
Water inlet filter is clogged.
Power nozzle is in low-
pressure position.
Pump is sucking air.
Not enough inlet water supply.
Pump is sucking air.
SOLUTION
Turn switch to the “ON”
( | ) position. Squeeze gun trigger.
Plug in power cord.
Try without extension cable.
Try a different outlet.
Replace with a 1” (25 mm) or 5/8”
(16 mm) garden hose.
Check garden hose for kinks,
leaks and blockage.
Open water source fully.
Remove filter and rinse in
warm water.
Turn power nozzle to high-
pressure position.
Check that hoses and fittings are airtight.
Turn “OFF” machine, and purge pump by
squeezing trigger gun until a steady flow
of water emerges through the nozzle.
Check that hoses and fittings are airtight.
Turn “OFF” machine, and purge pump by
squeezing trigger gun until a steady flow
of water emerges through the nozzle.
Water inlet filter is clogged. Remove filter and rinse with
warm water.
Turn water on fully.Check garden
hose for kinks, leaks or blockage

ENGLISH(Original Instructions)
PROBLEM
Unit does not reach
high pressure.
Pump is noisy
Water leaks from pump
(up to 10 drops per min-
ute is permissible).
Oil is dripping
Spray wand, extension,
or nozzle leaks.
Garden hose connection
leaks.
POSSIBLE CAUSE
Diameter of garden hose is
too small.
Detergent bottle or suction
tube not properly connected.
Detergent is too thick.
Filter on detergent suction
tube is clogged.
Damaged or clogged deter-
gent suction tube.
Nozzle is in high-pressure
position.
Discharge nozzle is ob-
structed.
Pump is sucking air
Water seals are damaged or
worn.
Oil seals are damaged or
worn.
Broken o-ring or plastic insert.
Missing/worn rubber washer.
SOLUTION
Add more detergent.
Check connections.
Dilute detergent.
remove build-up.
Run warm water through filter to
Remove obstruction or replace
detergent suction tube.
Turn nozzle tip to low-pressure
position.
fine needle.
Blow out or remove debris with a
Call the Toll-Free Hotline
Call the Toll-Free Hotline
Insert new washer.
Call the Toll-Free Hotline.
Tighten fittings.Loose fittings.
Loose fittings.
Water filter is clogged. warm wate. Remove water filter and rinse in
airtight. Turn off machine and
Check that hoses and fittings are
purge pump by squeezing trigger
gun until a steady flow of water
emerges through the nozzle.
Check that all fittings are tight.

ENGLISH(Original Instructions)
PROBLEM
Motor buzzes but fails
to run.
No Water
POSSIBLE CAUSE
Supply voltage below minimum.
System has residual pressure.
Voltage loss due to
extension cord.
Pressure washer not used for
long periods.
Residual friction among com-
ponents. Unit might hum.
Quick connect assembly is
attached in reverse.
Water supply is OFF.
Kink in the garden hose.
SOLUTION
Verify that only the pressure
washer is running on this circuit.
Turn unit “OFF”, squeeze trigger
on spray wand to release pressure,
then turn unit “ON”
Unplug any extension cords attached
and plug the unit directly
into the outlet.
Call the Toll-Free Hotline.
Disconnect water supply and
power ON for 2 to 3 seconds,
repeat couple times or until the
motor starts.
Verify that Inlet adapter (G2) is
attached to machine’s water inlet
and that the quick connect coupler
(G1) is attached to garden hose.
Turn ON water supply.
Remove kink in garden hose.
12
DISPOSAL
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.

ENGLISH(Original Instructions)
13
LIMITED WARRANTY
EN
LIMITED WARRANTY
Warrants this outdoor product to be free of defects in material and workmanship for 24 months from the date
of purchase by the original purchaser, subject to the limitations below. Please keep your invoice as proof of
date of purchase.
This warranty is only applicable where the product is used for personal and non-commercial purposes.
This warranty does not cover damage or liability caused by / due to misuse, abuse, accidental or intentional
acts by user, improper handling, unreasonable use, negligence, failure by end user to follow operating
procedures outlined in the user’s manual, attempted repair by non-qualified professional, unauthorized repair,
modification, or use of accessories and/or attachments not specifically recommended by authorized party.
Please see your local dealer for list of authorized service centers in your area.This warranty does not cover
belts, brushes, bags, bulbs or any part which ordinary wear and tear results in required replacement during
warranty period. This warranty does not cover transportation cost or consumable items such as fuses and
batteries.This limited warranty is void if the product’s original identification (trade mark, serial number)
markings have been defaced, altered or removed or if product is not purchased from an authorized reseller
or if product is sold AS IS and / or WITH ALL FAULTS.
Where permitted, the provisions of this limited warranty are in lieu of any other written warranty,
whether express or implied, written or oral, including any warranty of MERCHANTABILITY OR FITNESS
FORAPARTICULAR PURPOSE. IN NO EVENT SHALLWE BE LIABLE FOR SPECIAL, INCIDENTAL,
CONSEQUENTIALOR INCIDENTALDAMAGES. OUR MAXIMUM LIABILITY SHALL NOT EXCEED THE
ACTUAL PURCHASE PRICE PAID BY YOU FOR THE PRODUCT.
This warranty is valid only in the European Union, Australia and New Zealand. Outside these arears,
please contact your authorized GreenworksTools dealer to determine if another warranty applies.
AUTHORISED SERVICE CENTRE

ENGLISH(Original Instructions)
14
EC DECLARATION OF CONFORMITY FOR MACHINERY
Manufacturer:Changzhou Globe Tools Co., Ltd.
Address: No.65 Xinggang Road Zhonglou Zone Changzhou, Jiangsu 213000 P.R.China
Name and address of the person authorised to compile the technical file:
Name: Dennis Jacobson (Director of Outdoor Power Equipment)
Address: GLOBE TOOLS EUROPE AB,
åtbyggargatan 14
120 68 Stockholm
Sweden
Herewith we declare that the product
Category...................................................................................................High Pressure Washer
Model........................................................................................................51017
Serial number.........................................................................................See product rating label
Year of Construction...............................................................................See product rating label
2006/95/EC (LVD-Directive)
2004/108/EC (EMC-Directive), and
And furthermore, we declare that
EN 60335-2-79:2009
EN 60335-1:2002+A11:2004+ A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+15:2011
EN 62233:2008
EN 55014-1:2006+A1:2009
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN ISO 3744:1995
LlevelrewopdnuosderusaeM WA: 91.5 dB(A)
)A(Bd94levelrewopdnuosdeetnarauG
Conformity assessment method to Annex V/ Directive 2000/14/EC
EN
Place, date: Changzhou, 30/12/2011 Signature: Gary Gao Naixin (BEng, CEng, MIET)
Vice president of Engineering