GREISINGER G 7500 Series User manual

Operating Manual
Water analysis –hand-held
meter
G 7500 series
Keep for later use.
www.ghm-group.de
Companies / Brands of the GHM
Englisch

H87.0.0X.6C-01 Operating manual G 7500 Series page 2 of 34
Index
1GENERAL NOTE ...............................................................................................................3
2SAFETY................................................................................................................................3
2.1 INTENDED USE ..................................................................................................................3
2.2 SAFETY GUIDELINES..........................................................................................................3
2.3 QUALIFIED PERSONNEL......................................................................................................3
2.4 SAFETY SIGNS AND SYMBOLS ............................................................................................4
2.5 FORESEEABLE MISUSE .......................................................................................................5
2.6 SAFETY INSTRUCTIONS......................................................................................................5
3PRODUCT SPECIFICATION...........................................................................................7
3.1 SCOPE OF DELIVERY ..........................................................................................................7
3.2 OPERATING AND MAINTENANCE.......................................................................................7
3.3 CONNECTIONS...................................................................................................................7
3.4 SUPPORT AND RETAINING CLIP...........................................................................................8
4OPERATION.......................................................................................................................9
4.1 KEYPAD ............................................................................................................................9
4.2 STATUS LINE ...................................................................................................................10
4.3 DISPLAY ELEMENTS.........................................................................................................10
5START OPERATION.......................................................................................................11
6BASICS OF THE MEASUREMENT..............................................................................11
6.1 PHMEASUREMENT ..........................................................................................................11
6.2 BASICS ABOUT CONDUCTIVITY........................................................................................15
6.3 CONDUCTIVITY MEASUREMENT.......................................................................................15
6.4 ELECTRODES /MEASURING CELLS ...................................................................................15
6.5 TEMPERATURE COMPENSATION.......................................................................................16
6.6 DESIGN OF THE SENSOR GWO 5610................................................................................17
6.7 COMMISSIONING /FILLING OF THE SENSOR GWO 5610...................................................19
6.8 SENSOR GWO 5610 MAINTENANCE ................................................................................20
6.9 BASICS ABOUT OXYGEN MEASURING...............................................................................21
6.10 AMBIENT PRESSURE AND MEASURING DEPTH OF THE ELECTRODE ................................21
6.11 CORRECTION OF SALINITY............................................................................................21
7CONFIGURATION...........................................................................................................22
7.1 DEVICE MENU..................................................................................................................22
7.2 PHCHANNEL MENU .........................................................................................................25
7.3 TEMPERATURE CHANNEL MENU.......................................................................................27
7.4 OXYGEN CHANNEL MENU.................................................................................................27
7.5 CONDUCTIVITY CHANNEL MENU......................................................................................28
8ERROR CODES (IN DATASET)....................................................................................29
9CALIBRATION.................................................................................................................30
9.1 GENERAL INFORMATION..................................................................................................30
9.2 PHCALIBRATION.............................................................................................................30
9.3 O2CALIBRATION .............................................................................................................30
10 CALIBRATION AND ADJUSTMENT SERVICE.....................................................31
11 REPLACING RECHARGEABLE BATTERIES .......................................................31
12 RESHIPMENT AND DISPOSAL.................................................................................32

H87.0.0X.6C-01 Operating manual G 7500 Series page 3 of 34
12.1 RESHIPMENT ................................................................................................................ 32
12.2 DISPOSAL..................................................................................................................... 32
13 SPECIFICATION ..........................................................................................................33
13.1 MEASUREMENTS AND ACCURACY................................................................................. 33
13.2 GENERAL SPECIFICATION.............................................................................................. 34
14 TERMS OF LICENSE...................................................................................................34
14.1 FREERTOS.................................................................................................................. 34
14.2 FATFS.......................................................................................................................... 34
1 General Note
Read this document carefully and get used to the operation of the device before you
use it. Keep this document within easy reach near the device for consulting in case
of doubt.
2 Safety
2.1 Intended Use
The device is exclusively designed for measuring of pH and conductivity or pH and
dissolved oxygen in water (saltwater and freshwater).
Personnel which starts up, operates and maintains the device has to have sufficient
knowledge of the measuring procedure and the meaning of the resulting measured
values, this manual delivers a valuable help for this. The instructions of the manual
have to be understood, regarded and followed.
To be sure that there´s no risk arising due to misinterpretation of measured values,
the operator must have further knowledge in case of doubt - the user is liable for any
harm/damage resulting from misinterpretation due to insufficient knowledge.
The manufacturer will assume no liability or warranty in case of usage for other
purpose than the intended one, ignoring this manual, operating by unqualified staff
as well as unauthorized modifications to the device.
2.2 Safety guidelines
This device has been designed and tested in accordance with the safety regulations
for electronic devices.
However, its trouble-free operation and reliability cannot be guaranteed unless the
standard safety measures and special safety advises given in this manual will be
adhered to when using the device.
2.3 qualified personnel
The device may only be installed by qualified personnel who have read and
understood this manual and who are able to use the devices professionally. Qualified
personnel are persons who are familiar with the installation, assembly,
commissioning and operation of these devices and who have the necessary
qualifications to carry out their duties.

H87.0.0X.6C-01 Operating manual G 7500 Series page 4 of 34
2.4 Safety signs and symbols
The following signs in this document highlight warnings:
Caution! This symbol warns of imminent danger, death, serious
injuries and significant damage to property at non-observance.
This symbol indicates danger for living tissue as well as a variety of
materials, which can be damaged or destroyed when coming into
contact with this chemical. Caustic effect, protective equipment
required!
This Symbol indicates dangers to all living beings that may result in
death or acute or chronic health hazards when inhaled, swallowed, or
absorbed through the skin of this chemical.
This Symbol indicates irritant substances that can cause inflammation
on short-term, prolonged or repeated contact with the skin or mucous
membranes.
Attention! This symbol warns of possible dangers or dangerous
situations that can provoke damage to the device or environment at
non-observance.
Note! This Symbol indicates operations which, if ignored, may have an
indirect effect on operation, possibly leading to incorrect measurement
results or triggering an unforeseen reaction.
This symbol instructs the use of eye protection which protects the eyes
from harmful influences when working with powerful light, UV radiation,
laser, chemicals, dust, splinters or weather influences.
This symbol instructs the use of protective gloves which offer
protection from mechanical, thermal, chemical, biological or electrical
hazards.

H87.0.0X.6C-01 Operating manual G 7500 Series page 5 of 34
2.5 Foreseeable misuse
The fault-free function and operational safety of the product can only be guaranteed if
generally applicable safety precautions and the device-specific safety instructions for
this document are observed.
If these notices are disregarded, personal injury or death, as well as property damage
can occur.
This device must not at all be used in potentially explosive
environment! The usage of this device at potentially explosive areas
increases danger of deflagration, explosion or fire due to sparking.
This device is not suitable for medical applications.
The device is not suitable for direct contact with food products.
Take samples and dispose them correctly after the measurement.
2.6 Safety instructions
This device has been designed and tested in accordance with the safety regulations
for electronic devices.
However, its trouble-free operation and reliability cannot be guaranteed unless the
standard safety measures and special safety advises given in this manual will be
adhered to when using the device.
The O2 sensor contains potassium hydroxide. This causes burns. All
contact with the skin, clothing and eyes should be avoided.
Nevertheless, should contact occur, take
the following measures.
–Eyes: Flush with flowing water for at least 15 minutes, seek medical
attention!
–Skin: Wash with large amounts of water for several minutes!
–Clothing: Remove immediately!
–If swallowed: Drink large amounts of water, do not induce vomiting
and seek medical
Attention!
If there is a risk whatsoever involved in running it, the device has to be
switched off immediately and to be marked accordingly to avoid re-
starting.
Operator safety may be a risk if:
- there is visible damage to the device
- the device is not working as specified
- the device has been stored under unsuitable conditions for a longer
time.
In case of doubt, please return device to manufacturer for repair or
maintenance.

H87.0.0X.6C-01 Operating manual G 7500 Series page 6 of 34
Do not use this product as safety or emergency stop devices or in any
other application where failure of the product could result in personal
injury or material damage.
Failure to comply with these instructions could result in death or
serious injury and material damage
When interacting with chemicals at least the following points must be
ensured:
1. Obey all notes on the container of chemicals.
2. Obey all notes in the safety specification sheet of chemicals.
3. Consider any statutory provisions guidelines and guidelines of
chemicals when disposing!
This is also for accidentally spilled chemicals, dried residues,
soiled rags or similar.
4. Always wear suitable protective clothing (e.g. protection goggles,
safety gloves, face mask, etc.)!
5. Never eat, drink or smoke in the operational area of chemicals!
6. In case of problems instantly consult skilled personnel.
Suitable clean-up possibilities (eye wash, etc.) must exist
within spitting distance!
Trouble-free operation and reliability of the device can only be
guaranteed if the device is not subjected to any other climatic
conditions than those stated under specification

H87.0.0X.6C-01 Operating manual G 7500 Series page 7 of 34
3 Product Specification
3.1 Scope of delivery
The scope of supply includes:
Device with 3 rechargeable batteries type AAA
Short manual
Operating manual and calibration protocol as pdf file in mass storage memory.
3.2 Operating and Maintenance
1.Battery operation:
If the battery has been used up and needs to be recharged, the device will display
BAT. in the upper status line. The device will, however, continue operating correctly
for a certain time.
The battery has been completely discharged, if batteries empty is shown in the
main display and the red backlight will blink. The device will than turn off
automatically.
The device has a deep discharge protection, when the batteries
reach a limit value, the device can no longer be turned on!
2.Treat device and electrodes carefully. Use only in accordance with above
specification (do not throw, hit against etc.).
The measuring values can be influenced by contamination.
3.3 Connections
Front view
Connector
Probetype (standard)
BNC
pH (GE 125)
Banana
6 mm
(GND)
Resistive temperature probe
(PT 1000 or NTC 10 k)
common, needed only for
separate temperature probe
Banana
6 mm (T)
Resistive temperature probe
(GE 125 banana plug)
7-pol. LTW
Oxygen (GWO 5610) or
conductivity (LF 425)
Micro USB
For power supply or device
communication
Waterproofness is only guaranteed for plug connections in the
plugged-in state in combination with waterproof cable plugs.
The temperature measurement can be influenced by conductive
liquids on the banana sockets. We recommend always keeping the
connections dry.

H87.0.0X.6C-01 Operating manual G 7500 Series page 8 of 34
3.4 support and retaining clip
The stand is provided as a means to prop up or support the device in a stable
surface, for hanging on the wall or for attachment to a belt.
Instruction:
-Leave the stand collapsed in order to lay the product flat on a stable surface or
to hang it on a belt.
-Pull the grip labelled open in order to fold it out to a 90° angle. Now, the
product can be positioned on a stable surface.
-Pull the grip labelled open again in order to fold it out to a 180° angle. Now the
product can be hung.
-The product can be positioned ideally so that the display can always be read
clearly and easily depending on its use.
Pop-up clip closed
Pop-up clip at position 90°
Pop-up clip at position 180°
Device attached to a belt
Device set up on a table
Device suspended from
magnetic holder
GMH 1300

H87.0.0X.6C-01 Operating manual G 7500 Series page 9 of 34
4 Operation
4.1 Keypad
With the keypad the device functions, display
mode, etc. can be set by user interaction.
The display will contain specific information for the
F1 and F2 soft-keys.
F1 and F2 soft-key
Depending to the device state (view, menu,
channel, …) the dark accentuated texts in the
display directly above the soft-keys are describing
the soft-keys function (e.g. ‘back’ for F1 and
‘change’ for F2).
power button
Will turn the device on (only when rechargeable
batteries are not empty) or off (only when the logger
is not running).
device settings
Will open the device-settings-menu.
Here anything that’s not related to a physical
measuring e.g. the date, time USB-mode and
language can be changed.
directional pad (up, down, right, left)
For navigation within a menu, for changing the
selected channel (up and down) or changing the
view (right and left).

H87.0.0X.6C-01 Operating manual G 7500 Series page 10 of 34
4.2 Status line
The status line is the first line in the display.
Display
Meaning
Current time
If time is flashing, time must be reseted
!
Internal memory error. When this error won’t
disappear after restarting the device, it should
be returned for repairing. The device will go to a
safe fallback mode were device settings are
stored and recalled from the mass storage
memory if this is available.
S
Saving to the internal mass storage memory
takes longer than intended. When the S will be
shown permanently in the display, please let
Windows check the mass storage device for
errors. When the S still shows up, the device
needs to be send back for repairing.
A
Alarm of a channel is active
USB
USB connection has been established.
LOG
Logger is active
BAT
Rechargeable battery capacity critically low
Battery indicator
If the battery capacity flashes, the battery is
being charged
4.3 Display elements
Views can be changed by the right and left keys of the directional pad. With the keys
up and down the channel can be changed.
Table view
Chart view
Large view
All channels in one row
Chart of one channel
Display of one channel
with specific parameters
(here: electrode quality
and temperature
compensation)

H87.0.0X.6C-01 Operating manual G 7500 Series page 11 of 34
4.3.1 Menu
Depending on the selected channel, you can switch to the channel configuration
menu by pressing the function key F2. Here, channel-specific settings can be made.
5 Start operation
Charge the rechargeable batteries by connecting a power supply or the computer to
the micro USB connector.
Connect all desired probes or electrodes.
Turn on the device by pressing the power button.
Change date, time and language by pressing the device settings key and save the
changes made.
6 Basics of the measurement
At first the basics of all measurements will be depicted. Some channel specific
settings depend on these basics.
6.1 pH measurement
The pH value describes the acidic or alkaline behavior of an aqueous solution.
pH values below 7 are acidic (smaller values indicate higher acidity), and values
above 7 are alkaline; pH 7 = neutral.
The pH measurement is very precise, but also sensitive. The measured signals are
very weak (high-impedance), especially when measured in weak or low-ion media.
Therefore, always take measures to
To determine the pH value of a solution, its temperature needs to be
known. The reason is that most liquids change their pH value with the
temperature.
- avoid interference (electrostatic charges, etc.)
- keep plug contacts clean and dry
- prevent electrodes (except special waterproof versions) from extended
immersion above the shaft
- calibrate the electrode at sufficient intervals (see below). The frequency of
calibration can range from every hour to several weeks, depending on the
electrode and the application.
- use a suitable electrode. See chapter Fehler! Verweisquelle konnte nicht
gefunden werden.

H87.0.0X.6C-01 Operating manual G 7500 Series page 12 of 34
6.1.1 Design
1. Coaxial cable
2. Reference electrode
3. Measuring electrode
4. Refill opening
5. Electrolyte
6. Internal buffer
7. Diaphragm
8. Glass membrane / source layer
The diaphragm, which establishes a connection between the electrolyte and the liquid
to be measured, can be designed in different ways. Clogging or soiling of the
diaphragm is a frequent cause of a malfunctioning or sluggish electrode. Always
handle the glass membrane with extreme care. The so-called source layer forms
there. This is crucial for the measurement and must always be kept moist.
There are also electrodes with integrated temperature sensors.
6.1.2 pH electrode
Normally, so-called pH single-rod measuring chains are used. They
include all necessary components that are integrated in an electrode.

H87.0.0X.6C-01 Operating manual G 7500 Series page 13 of 34
6.1.3 Further information
pH electrode is a wear part. If the signal is very slow or the required values are no
longer observed after careful cleaning and possible regeneration, the electrode must
be replaced. When using the electrodes, be aware that various substances in
aqueous solutions can corrode glass and that chemicals can produce a chemical
reaction with the KCl solution in the electrode, which can result in blockage of the
diaphragm.
Examples:
In solutions that contain proteins, such as for measurements in medical and
biological applications, KCl can cause denaturation of the protein.
Coagulated paints
Solutions that contain high concentrations of silver ions
Substances that accumulate on the glass membrane or the diaphragm affect the
measurement and must be removed regularly. This can be achieved for example
with automatic cleaning systems.
6.1.4 Choosing a pH electrode
GE 100 BNC is a universal electrode with two ceramic diaphragms and liquid
GE 101 BNC is preferably used for small sample amounts. It comprises a glass
electrode with two ceramic diaphragms and liquid electrolyte.
GE 104 BNC is preferably used for measurements in low-ionic media, such as
rainwater, aquarium water and deionised water.
GE 114 WD is a universally applicable, durable and low-maintenance gel
electrode with Pellon diaphragm. It can be used for measurements in drinking
water, swimming pools, aquaria and slightly contaminated waste water.
GE 117 BNC is a temperature-compensated gel electrode with two ceramic
diaphragms and PH 13.5 cable screw coupling.
GE 120 BNC is an insertion electrode and is preferably used for measurements
in cheese, fruit and meat. For measurements in products containing proteins,
the electrode must be cleaned with a special cleaner. For this purpose, we
recommend the GRL 100 pepsin cleaning solution.
GE 125 BNC is a waterproof, universally applicable, durable and low-
maintenance gel electrode with ceramic diaphragm. It can be immersed above
the shaft for an extended time.
GE 151 BNC is a glass electrode and is preferably used in galvanic
applications for paints and lacquers.
GE 173 BNC is an alkaline-resistant glass electrode with ground diaphragm
and gel electrolyte for chemical and waste water applications.

H87.0.0X.6C-01 Operating manual G 7500 Series page 14 of 34
6.1.5 Service life
The service life of electrodes is normally at least 8 to 10 months. When
cared for properly, this can usually increase to more than 2 years. The
actual life will vary depending on the particular application.
6.1.6 Care and maintenance
The GAK 1400 working and calibration set includes all necessary
products for calibration, care and maintenance of the electrode.
Normal cleaning takes place with the GRL 100 pepsin cleaning
solution into which the electrode is immersed for 5 minutes before
being rinsed off with clean water.
Crystallization of the 3 mol/l KCL solution is unavoidable. Crystallized
potassium chloride on the protective cap and shaft can easily be
removed with a fingernail or cloth and is therefore does not constitute
a defect or cause for complaint.
Dirty electrodes must be cleaned. The suitable cleaning agents for the pH glass
membrane are listed in the table below.
Impurities
Cleaners
General residue
Mild detergent
Inorganic coatings
1 mol/l HCl solution or GRL 100 pepsin
cleaning solution
Metal compounds
1 mol/l HCl solution or GRL 100 pepsin
cleaning solution
Oil and grease
Special cleaner or solvent
Biological coatings with protein
1% pepsin enzyme in 0.1 molar GRL 100
HCl solution
Biological coatings with protein
Acetone
Extremely resistant residues
Hydrogen peroxide or sodium hypochloride
The material of the pH probe must always be protected. Plastic shafts must not be
cleaned in solvents, etc. If in doubt, contact the manufacturer to inquire about suitable
cleaners for the existing electrode. This is also important in the case of aggressive
substances or other substances that are not primarily water-based!

H87.0.0X.6C-01 Operating manual G 7500 Series page 15 of 34
6.2 Basics about conductivity
Definition of conductivity :
The ability of a material to conduct electric current:   

l: length of the material
A: diameter
R: measured resistance
Unit 󰇟󰇠  
  , common for liquids:   and  
The conductivity is the reciprocal value of the resistivity.
(The conductance is the reciprocal value of the measured resistance R)
6.3 Conductivity measurement
The conductivity measurement is a rather uncomplicated measurement. The
standard measuring cells are stable for a long time if used correctly and can be
adjusted by slope correction.
Range
1
2
3
4
45..500 mS/cm
5.0..50.0
mS/cm
500..5000
µS/cm
0.0..500.0
µS/cm
Within the integrated automatic range selection, the range with the best resolution is
automatically selected.
6.4 Electrodes / measuring cells
6.4.1 Design and selection
Basically there are two types of measuring cells: 2-pole and 4-pole cells. The
operation is done similarly; the 4-pole measuring cells can compensate polarization
effects and –up to some degree –soiling due to its complex measuring method.
2-pole measuring cell
4-pole measuring cell
6.4.2 Calibration / Adjustment of measuring cells
Especially in harsh environments and over long time the cell constants of measuring
cells are drifting. Depending on the application and usage we recommend a regular
checking of the precision of the measuring chain: instrument + cell. For this there are
control solutions available (GKL 100, 101, 102). At normal usage a checking each
half year is recommended.

H87.0.0X.6C-01 Operating manual G 7500 Series page 16 of 34
6.5 Temperature compensation
The conductivity of aqueous solutions depends on its temperature. The temperature
dependency is strongly dependent on the type of solution. The temperature
compensation recalculates solutions’ conductivity to a consistent reference
temperature. The most common reference temperature is 25 °C, but 20 °C can also
be selected.
6.5.1 Temperature compensation “NLF” according to EN 27888
For most applications (e.g. in the area of fish farming, surface or drinking water
measurements, etc.) the non-linear temperature compensation for natural water
(“nLF”, according to EN 27888) is sufficiently accurate.
Recommended application range of nLF-compensation: between 60 µS/cm and 1000
µS/cm.
6.5.2 Linear temperature compensation
If the actual function needed for exact temperature compensation is not known,
“linear temperature compensation” is normally selected (Menu, t.Cor = Lin, t.Lin
corresponds), i.e. one assumes that the actual temperature dependency at the
considered concentration range is approximately equal:
 
  
 󰇛  󰇜
Temperature coefficient of about 2.0 %/K are most common.
A temperature coefficient can be determined for example by measuring a solution
with deactivated temperature compensation at two different temperatures (T1 and
T2).
 󰇛 󰇜
󰇛 󰇜
TKlin is the value input at the menu
LFT1 conductivity at temperature T1
LFT2 conductivity at temperature T2

H87.0.0X.6C-01 Operating manual G 7500 Series page 17 of 34
6.6 Design of the sensor GWO 5610
6.6.1 General
The oxygen sensor is an active sensor. It consists of a platinum cathode, a lead
anode and potassium hydroxide (KOH) as an electrolyte. If oxygen is present, it is
reduced on the platinum cathode and the sensor delivers a signal. If no oxygen is
present, no signal is delivered. The anode is consumed by the oxygen measurement.
The sensor ages. Furthermore, the sensor loses water through the permeable
membrane, in particular, when it is stored in dry air. Therefore, it should be checked
and maintained regularly and replaced as necessary.
The electrode contains potassium hydroxide. This causes burns. All
contact with the skin, clothing and eyes should be avoided.
Nevertheless, should contact occur, take the following measures.
Eyes: Flush with flowing water for at least 15 minutes, seek medical
attention!
Consult a doctor.
Always store oxygen sensor GWO 5610 wet!
- In a storage bottle filled with water or
- place in a container with water.
After prolonged storage before the measurement, clean the membrane
with a soft paper towel of possible coverings (algae, bacteria, ...).
6.6.2 Design
Shaft
Membrane
head
Refill opening
Storage bottle
Platinum electrode

H87.0.0X.6C-01 Operating manual G 7500 Series page 18 of 34
Platinum electrode
If oxygen is present, it is reduced on the platinum electrode and the sensor delivers a
signal. Soiling on the platinum electrode or between the membrane and electrode can
influence the measurement.
Storage bottle
The storage bottle is provided to keep the membrane moist. The service life of the
sensor is extended as a result. Distilled or deionized water is in the storage bottle; do
not add any other liquids!
Membrane head
The membrane head is covered with a thin plastic membrane. Faulty measurements
will occur if the membrane is damaged or there are large air bubbles or even an air
bubble ring on the membrane. This can also be the cause if a sensor can no longer
be calibrated. The GWOK 02 membrane head is a spare part and can be re-ordered
separately.
Refill opening
Electrolyte must be filled or added for the initial commissioning of a sensor which is
delivered dry, when performing maintenance or after use at high temperatures.
6.6.3 Service life
The sensor signal deteriorates relatively quickly at the end of the service life of the
sensors. The electrode evaluation in %, therefore, can only be used as a guide value.
A value of 70% does not mean that exactly 70% of the service life is still available,
rather that the electrode signal has 70% of a comparison signal.
The sensor evaluation is updated by the measuring device after a
successfully performed calibration of the oxygen sensor.
The nominal service life can be reduced significantly due to use. Influential factors
include:
▪ Storage / operating temperature
▪ Contamination of the measured water
▪ Mechanical stress of the sensor membrane
▪ Storage in dry air
▪ Continuous use in elevated carbon dioxide concentrations
6.6.4 Operating position
The oxygen sensor should be arranged vertically upwards with the connecting cable.
A slight angle of inclination does not impair the measurement.

H87.0.0X.6C-01 Operating manual G 7500 Series page 19 of 34
6.6.5 Measurement accuracy
The measurement accuracy can be impaired by:
▪ An inadequate flow below the necessary value of approx. 30cm/sec.
▪ The water temperature and sensor temperature must be the same. The most
accurate measurements are provided when the measuring temperature is
calibrated.
6.6.6 Visible residues inside the membrane cap
As a reaction product, lead oxides (brown or red, from reaction with oxygen) and lead
carbonate (white, from reaction with carbon dioxide) are created during operation on
the lead anode. These substances can collect on the membrane, but they do not
usually affect the measurement function. Most of these substances can be removed
during the maintenance of the sensor.
Prior to screwing on the membrane cap, they should be removed as far as possible in
order to prevent particles from being trapped between the membrane and the
platinum cup. A rapid or excessive formation of lead carbonate after commissioning is
an indication of air in the sensor. This is usually due to incomplete filling or a leak due
to improper fitting of the cap / fill screw or membrane leak.
6.7 Commissioning / filling of the sensor GWO 5610
The electrode contains potassium hydroxide. This causes burns. All
contact with the skin, clothing and eyes should be avoided.
Nevertheless, should contact occur, take the following measures.
a) Eyes: Flush with flowing water for at least 15 minutes, seek medical
attention!
b) Skin: Wash with large amounts of water for several minutes!
c) Clothing: Remove immediately!
d) If swallowed: Drink large amounts of water, do not induce vomiting
and seek medical attention!
Protective goggles must be worn for all of the following activities!
Protective gloves must be worn for all of the following activities!
The sensor is delivered dry. Therefore, the sensor is well-suited for storage. The
sensor must be filled in good time before the measurement. A wait time of approx. 2
hours after filling should be planned in order to allow the sensor to stabilize.

H87.0.0X.6C-01 Operating manual G 7500 Series page 20 of 34
6.8 Sensor GWO 5610 maintenance
After every calibration the sensor quality in % will be shown in the large digit display.
When the quality is below 25 % the sensor should be maintained.
Attention! The electrolyte is corrosive.
To maintain electrode please proceed as follows:
1. Unscrew diaphragm head and wipe clean of electrolyte solution using a paper
cloth. Do not touch electrolyte. If your skin had contact with electrolyte,
immediately rinse thoroughly with clear water.
2. Clean silver cathode with sand paper (grain size 240). Do not polish silver
cathode, surface should stay rough. Remove all dust.
3. Remove filling screw and top up lost electrolyte (e.g. using disposable syringe))
4. Put back and tighten filling screw.
5. Top up diaphragm head with electrolyte avoiding air bubbles and place on table
(cover table with absorbent paper first).
6. Keep electrode in a vertical position and screw diaphragm head to the electrode
from the bottom. Electrolyte will be forced out of the diaphragm head and spill
over (put on disposable gloves or use paper towel to touch diaphragm head).
7. Wipe up excess electrolyte with paper cloth.
8. Check cathode for air bubbles.
If there are large air bubbles, remove diaphragm head again and repeat process
as of point 5. If O-ring has been damaged, it has to be replaced.
When maintenance has been completed plug on protective flask. Re-connect
electrode to measuring device and wait for at least 3 hours till electrode can be
calibrated.