GREISINGER GMH 3451 User manual

H72.0.11.6C-04
GHM Messtechnik GmbH • Standort Greisinger
Hans-Sachs-Str. 26 • D-93128 Regenstauf
 +49 (0) 9402 / 9383-0  +49 (0) 9402 / 9383-33  [email protected]

Please carefully read these instructions before use!

Please consider the safety instructions!

Please keep for future reference!
as of version 1.3 GMH 3451
WEEE-Reg.-Nr. DE 93889386
Operating manual
Conductivity measuring device
with data logger

H72.0.11.6C-04 Operating Manual GMH 3451 page 2 of 18
_____________________________________________________ _____________________________________________________________________________
Index
1GENERAL NOTE......................................................................................................................................................3
2SAFETY......................................................................................................................................................................3
2.1INTENDED USE ......................................................................................................................................................3
2.2SAFETY SIGNS AND SYMBOLS................................................................................................................................3
2.3SAFETY GUIDELINES..............................................................................................................................................3
3PRODUCT SPECIFICATION..................................................................................................................................4
3.1SCOPE OF SUPPLY ..................................................................................................................................................4
3.2OPERATION AND MAINTENANCE ADVICE..............................................................................................................4
4HANDLING................................................................................................................................................................5
4.1DISPLAY ELEMENTS...............................................................................................................................................5
4.2PUSHBUTTONS.......................................................................................................................................................5
4.3CONNECTIONS .......................................................................................................................................................5
4.4POP-UP CLIP...........................................................................................................................................................6
5START OPERATION................................................................................................................................................6
6PRINCIPLES OF THE MEASUREMENTS...........................................................................................................7
6.1BASICS ABOUT CONDUCTIVITY .............................................................................................................................7
6.2CONDUCTIVITY MEASUREMENT............................................................................................................................7
6.3RESISTIVITY MEASUREMENT.................................................................................................................................7
6.4TDS MEASUREMENT..............................................................................................................................................7
6.5SALINITY MEASUREMENT......................................................................................................................................7
6.6ELECTRODES /MEASURING CELLS.........................................................................................................................8
6.6.1Design............................................................................................................................................................8
6.6.2Calibration / Adjustment of measuring cells..................................................................................................8
6.7TEMPERATURE COMPENSATION ............................................................................................................................8
6.7.1Temperature compensation “nLF” according to EN 27888 .........................................................................8
6.7.2Linear temperature compensation and determination of temperature coefficient “t.Lin“............................8
7CONFIGURATION...................................................................................................................................................9
8DATA LOGGER......................................................................................................................................................11
8.1MANUAL RECORDING (“FUNC-STOR”)................................................................................................................11
8.2AUTOMATIC RECORDING WITH SELECTABLE CYCLE TIME “FUNC CYCL”.........................................................12
9UNIVERSAL OUTPUT...........................................................................................................................................13
9.1SERIAL INTERFACE..............................................................................................................................................13
9.2ANALOGUE OUTPUT............................................................................................................................................14
10ADJUSTMENT OF TEMPERATURE INPUT.................................................................................................14
11AUTOMATIC ADJUSTMENT/CALIBRATION OF CELL CORRECTION..............................................14
12GLP........................................................................................................................................................................15
12.1CALIBRATION INTERVAL (C.INT).....................................................................................................................15
12.2CALIBRATION STORAGE (READ CAL).............................................................................................................15
13ALARM („AL.“)...................................................................................................................................................15
14REAL TIME CLOCK (“CLOC”).......................................................................................................................16
15ACCURACY CHECK / ADJUSTMENT SERVICE ........................................................................................16
16ERROR AND SYSTEM MESSAGES................................................................................................................16
17RESHIPMENT AND DISPOSAL.......................................................................................................................17
17.1RESHIPMENT ....................................................................................................................................................17
17.2DISPOSAL INSTRUCTIONS.................................................................................................................................17
18SPECIFICATION.................................................................................................................................................18

H72.0.11.6C-04 Operating Manual GMH 3451 page 3 of 18
_____________________________________________________ _____________________________________________________________________________
1 General Note
Read this document carefully and get used to the operation of the device before you use it. Keep this
document within easy reach near the device for consulting in case of doubt.
2 Safety
2.1 Intended Use
The device is designed for measuring conductivity, resistivity, salinity and TDS in fluids – using a
permanently connected electrode (measuring cell).
It is designed for the mobile use or the stationary operation in a controlled electromagnetic environment (lab).
Personnel which starts up, operates and maintains the device has to have sufficient knowledge of the
measuring procedure and the meaning of the resulting measured values, this manual delivers a valuable
help for this. The instructions of the manual have to be understood, regarded and followed.
To be sure that there´s no risk arising due to misinterpretation of measured values, the operator must have
further knowledge in case of doubt - the user is liable for any harm/damage resulting from misinterpretation
due to insufficient knowledge.
The manufacturer will assume no liability or warranty in case of usage for other purpose than the intended
one, ignoring this manual, operating by unqualified staff as well as unauthorized modifications to the device.
2.2 Safety signs and symbols
Warnings are labelled in this document with the followings signs:
Caution! This symbol warns of imminent danger, death, serious injuries
and significant damage to property at non-observance.
Attention! This symbol warns of possible dangers or dangerous
situations which can provoke damage to the device or environment at
non-observance.
Note! This symbol point out processes which can indirectly influence
operation or provoke unforeseen reactions at non-observance.
2.3 Safety guidelines
This device has been designed and tested in accordance with the safety regulations for electronic devices.
However, its trouble-free operation and reliability cannot be guaranteed unless the standard safety measures
and special safety advises given in this manual will be adhered to when using the device.
1. Trouble-free operation and reliability of the device can only be guaranteed if the device is not subjected to
any other climatic conditions than those stated under "Specification".
If the device is transported from a cold to a warm environment condensation may cause in a failure of the
function. In such a case make sure the device temperature has adjusted to the ambient temperature
before trying a new start-up.
2. If there is a risk whatsoever involved in running it, the device has to be switched off
immediately and to be marked accordingly to avoid re-starting.
Operator safety may be a risk if:
- there is visible damage to the device
- the device is not working as specified
- the device has been stored under unsuitable conditions for a longer time.
In case of doubt, please return device to manufacturer for repair or maintenance.
3. When connecting the device to other devices the connection has to be designed most thoroughly as
internal connections in third-party devices (e.g. connection GND with protective earth) may lead to
undesired voltage potentials that can lead to malfunctions or destroying of the GMH 5155 and the
connected devices.

H72.0.11.6C-04 Operating Manual GMH 3451 page 4 of 18
_____________________________________________________ _____________________________________________________________________________
This device must not be run with a defective or damaged power supply unit.
Danger to life due to electrical shock!
4. Do not use these products as safety or emergency stop devices or in any other application
where failure of the product could result in personal injury or material damage.
Failure to comply with these instructions could result in death or serious injury and material
damage.
5. This device must not be used at potentially explosive areas! The usage of this device at
potentially explosive areas increases danger of deflagration, explosion or fire due to
sparking.
3 Product Specification
3.1 Scope of supply
The scope of supply includes:
GMH 3451, incl. 9V-battery
Operating manual
3.2 Operation and maintenance advice
1. Battery operation:
If and ‘bAt’ is shown in the lower display the battery has been used up and needs to be replaced.
However, the device will operate correctly for a certain time. If ‘bAt’ is shown in the upper display the
voltage is too low to operate the device; the battery has been completely used up.
The battery has to be taken out, when storing device above 50°C. We recommend taking out
battery if device is not used for a longer period of time.
After recommissioning the real-time clock has to be set again.
2. Treat device and sensor carefully. Use only in accordance with above specification. (do not throw, hit
against etc.). Protect plug and socket from soiling.
3. Mains operation with power supply:
When using a power supply please note that operating voltage has to be 10.5 to 12 V DC.
Do not apply overvoltage!! Cheap 12V-power supplies often have excessive no-load voltage.
We, therefore, recommend using regulated voltage power supplies.
Trouble-free operation is guaranteed by our power supply GNG10/3000.
Prior to connecting the power supply to the mains make sure that the operating voltage stated
at the power supply is identical to the mains voltage.

H72.0.11.6C-04 Operating Manual GMH 3451 page 5 of 18
_____________________________________________________ _____________________________________________________________________________
4 Handling
4.1 Display elements
1
Main display: conductivity (mS/cm, µS/cm)
resistivity (kΩcm)
TDS / total dissolved solids (mg/l)
salinity (SAL)
2Secondary display: measuring value temperature
3Arrows to selected measuring unit
4Warning signal: indicates low battery or missing
calibration
5Display elements to show minimum / maximum /
memorized measuring value
6nLF, Lin: display element for selected
temperature compensation
7%/K, 1/cm: additional configuration units
8logg-arrow: logger is ready
arrow flashing: automatic recording (Logg CYCL) is
active
4.2 Pushbuttons
On / Off key
press shortly: switch on/off instrument
Set / Menu:
press shortly: change-over between measuring units
(only if „InP: SEt“ is selected)
press for 2 sec. (menu): invoke configuration menu
+
min/max when taking measurements:
press shortly: min. or max. value is displayed
press for 2 sec: the corresponding value is deleted
Configuration:
to enter values or change settings
CAL: only at mode ‘cond’=conductivity:
press for 2 sec: start cell correction adjustment
Store/Quit:
Logger off: hold and save current measuring value
(‘HLD’ is displayed)
Logger on: Operation of data logger – chapter 8
Set/Menu: confirm settings, return to measuring
4.3 Connections
Universal output: interface, analog output (see
chapter 9 “Universal output“)
Permanently connected measuring cell with
integrated temperature probe
Power supply: The mains socket (1,9 mm inner diameter) is located at the left side of the
instrument for 10,5-12 V DC supply
A
l
l
co
n
tacts
h
a
v
e
to
be
p
r
otected
aga
in
st
d
ir
t
a
n
d
m
o
i
stu
r
e
!
MAX DIF
MIN HLD
%
°C
°F
S
Logg %/ K AL
mS
nLF
SAL mg/l
1/cm
Lin
kOhm 
123
456
ON
OFF max
Store
CAL
min
Set
Menu Quit

H72.0.11.6C-04 Operating Manual GMH 3451 page 6 of 18
_____________________________________________________ _____________________________________________________________________________
4.4 Pop-up clip
Handling:
‐Pull at label “open” in order to swing open the pop-up clip.
‐Pull at label “open” again to swing open the pop-up clip further.
Pop-up clip closed
Pop-up clip at position 90°
Pop-up clip at position 180°
Function:
‐The device with a closed pop-up clip can be plainly laid onto a table or attached to a belt, etc.
‐The device with pop-up clip at position 90° can be set up on a table, etc.
‐The device with pop-up clip at position 180° can be suspended from a screw or the magnetic holder
GMH 1300.

Deviceattachedtoabelt



Devicesetuponatable

Devicesuspendedfrom
magneticholder
GMH1300
5 Start Operation
Turn device on via key.
After segment test the device displays some information on its configuration:
if cell correction scale was changed (cell correction scale unequal 1.000)
(see chapter 11 Automatic adjustment/calibration of cell correction)
if zero point or slope correction is active
(see chapter 10 Adjustment of temperature input)
After that the device is ready for measuring.

H72.0.11.6C-04 Operating Manual GMH 3451 page 7 of 18
_____________________________________________________ _____________________________________________________________________________
6 Principles of the measurements
6.1 Basics about conductivity
Definition of conductivity: The ability of a material to conduct electric current: γ 
•
l: length of the material
A: diameter
R: measured resistance
Unit 󰇟γ󰇠  
  , common for liquids:   and  
The conductivity is the reciprocal value of the resistivity.
(The conductance is the reciprocal value of the measured resistance R)
6.2 Conductivity measurement
The conductivity measurement is a rather uncomplicated measurement. The standard electrodes are stable
for a long time if used correctly and can be adjusted by an integrated Cal-function.
Measuring ranges: 0.0 - 200.0 µS/cm 0 - 2000 µS/cm 0.00 - 20.0 mS/cm 0.0 - 200.0 mS/cm 0 - 400 mS/cm
If the range selection is set to „Auto Range“, the range with the best resolution is automatically selected. In
this case, the output value of the interface will always be the measured value with the highest possible
resolution (e.g. display value: 187.6 mS/cm interface output: 187600.0 µS/cm).
6.3 Resistivity measurement
The resistivity is the reciprocal value of the conductivity and the device displays it in kOhm•cm.
Measuring ranges: 0.000 - 2.000 kOhm*cm 0.00 – 20.00 kOhm*cm 0.0 - 100.0 kOhm*cm
If the range selection is set to „Auto Range“, the range with the best resolution is automatically selected.
However, logger or interface operation requires a manual/fixed selection of the measuring range from the
table above (No logger/interface operation with Auto-range!).
6.4 TDS measurement
At the TDS (total dissolved solids) measurement the filtrate dry residue is determined by means of the
conductivity and a conversion factor (C.tdS). Well suited for easy concentration measurements of e.g. salt
solutions. The determined value is displayed in mg/l.
Measuring ranges: 0.0 - 200.0 mg/l 0 – 2000 mg/l
If the range selection is set to „Auto Range“, the range with the best resolution is automatically selected. In
this case, the output value of the interface will always be the measured value with the highest possible
resolution (e.g. display value: 1876 mg/l interface output: 1876.0 mg/l).
Displayed value TDS = conductivity [in µs/cm, nLF-temp. comp. at 25°C] •C.tdS (input at menu)
Approximately:
C.tdS
0.50 Monovalent salts with 2 ion types (NaCl, KCl, etc.)
0.50 Natural waters / surface waters, drinking water
0.65 - 0.70 e.g. salt concentration of aqueous fertilizer solutions
Attention: This are only approximate values – good for estimations, but no precise measurement.
For precise measurements the conversion value has to be determined for the corresponding solution for the
relevant concentration range.
This may be done by comparison with known reference solutions or by actually evaporating a certain amount
of solution with determined conductivity and subsequent weighing of the dry residue.
6.5 Salinity measurement
At the salinity measurement “SAL” the salinity (salt content) of seawater is determined (based on:
International Oceanographic Tables; IOT). Standard seawater has a salinity of 35 ‰ (35 g salt per 1 kg
seawater). Commonly the measured value is displayed dimensionless in ‰ (g/kg).
Additionally the term “PSU” (Practical Salinity Unit) is sometimes used, the displayed value is the same.
The salinity measurement has its “own” temperature compensation, i.e. the temperature is automatically
taken into account for the salinity measurement. The menu settings regarding the temperature compensation
are ignored.

H72.0.11.6C-04 Operating Manual GMH 3451 page 8 of 18
_____________________________________________________ _____________________________________________________________________________
The salt composition of the different seas is not the identical. Depending on place, weather,
tides, etc. there may be considerable divergences to the 35 ‰ according to IOT.
Additionally the salt composition may influence the ratio between salinity and actual salt
content.
6.6 Electrodes / measuring cells
6.6.1 Design
Basically there are two types of measuring cells: 2-pole and 4-pole cells. The operation is done similarly; the
4-pole measuring cells can compensate polarization effects and – up to some degree – soiling due to its
complex measuring method.
2-pole measuring cell 4-pole measuring cell
6.6.2 Calibration / Adjustment of measuring cells
Especially in harsh environments and over long time the cell constants of measuring cells are drifting.
Depending on the application and use we recommend a regular checking of the precision of the measuring
chain: instrument + cell. For this there are control solutions available (GKL 100, 101, 102). At normal use a
checking each half year is recommended (see chapter 11 Automatic adjustment/calibration of cell
correction). A system check at the manufacturer is recommended in case of doubt: see chapter 15 Accuracy
Check / Adjustment Service).
6.7 Temperature compensation
The conductivity of aqueous solutions depends on its temperature. The temperature dependency is strongly
dependent on the type of solution. The temperature compensation recalculates solutions’ conductivity to a
consistent reference temperature. The most common reference temperature is 25 °C.
6.7.1 Temperature compensation “nLF” according to EN 27888
For most applications (e.g. in the area of fish farming, surface or drinking water measurements, etc.) the non-
linear temperature compensation for natural water (“nLF”, according to EN 27888) is sufficiently accurate.
The common reference temperature is 25 °C.
Recommended application range of nLF-compensation: between 60 µS/cm and 1000 µS/cm.
6.7.2 Linear temperature compensation and determination of temperature coefficient “t.Lin“
If the actual function needed for exact temperature compensation is not known, “linear temperature
compensation” is normally selected (Menu, t.Cor = Lin, t.Lin correspondsTK), i.e. one assumes that the
actual temperature dependency at the considered concentration range is approximately equal:
LF LF
1  TK
100% •󰇛Tx  Tref󰇜
Temperature coefficient of about 2.0 %/K are most common.
A temperature coefficient can be determined for example by measuring a solution with deactivated
temperature compensation at two different temperatures (T1 and T2).
TK 󰇛LF LF
󰇜• 100%
󰇛T1  T2󰇜•LF

TKlin is the value input at the menu “t.Lin”.
LFT1 conductivity at temperature T1
LFT2 conductivity at temperature T2

H72.0.11.6C-04 Operating Manual GMH 3451 page 9 of 18
_____________________________________________________ _____________________________________________________________________________
7 Configuration
Some menu points depend on current device settings (e.g. some points are locked if logger
memory contains data sets).
To change device’s settings, press „Menu“ for 2 seconds. This will activate the configuration menu
(main display: “SEt”). Pressing „Menu“ changes between the menus points, pressing jumps to
the referring parameters, which can be selected with key .
The parameter value can be changed with or . Pressing „Menu“ again jumps back to the main
configuration menu and saves the settings. Pressing „Quit“ finishes the configuration.
Pressing “menu” and “store” at the same time for more than 2 seconds will reset the
device to factory defaults.
If there are data sets stored and logger is set to “manual recording” (“Func Stor”) the first
menu point displayed is “rEAd Logg” (see chapter “8 Data Logger“)
If no key is pressed for more than 2 minutes the configuration will be aborted. All changes will
be discarded!
Menu Paramete
r
V
alue Description
or
rEAd Logg: Read manual recordings,
see chapter 8.1 Manual recording (“Func-Stor”)
Set Confi
g
uration: General confi
g
uration
Input: Selection of measured variable **
Cond Conductivity
rESi Resistivity
tdS Total dissolved solids
SAL Salinity
SEt Change-over measured variables by Set-key
TDS measurement: conversion factor (only if Inp = tdS)
0.40 - 1.00 Conversion factor for TDS measurement
Cell Corr: Adjustment of cell correction: multiplication factor
0.800 -
1.200 Multiplication factor of cell correction Factory setting: 1.000
Range: Selection of display range (conductivity, resistivity or tdS)
Auto Automatic range selection
200.0 µS/cm Lowest selectable range (conductivity)
… …
400 mS/cm Highest selectable range (conductivity)
Automatic adjustment/calibration with reference solution (only if Inp = Cond)
Edit Manual adjustment to reference value
REF.S Choice of standard reference solutions
REF.S: Choice of standard reference solutions for automatic adjustment/cal.
1413 µS/cm Reference solution 0.01 M KCL
2760 µS/cm 0.02 M KCL
12.88 mS/cm 0.1 M KCL
50 mS/cm Sea-water reference solution KCL
111.8 mS/cm 1 M KCL
Unit t: Selection of temperature unit
°C All temperature values in degree Celsius
°F All temperature values in degree Fahrenheit
Temperature compensation (not for InP = SAL)
oFF No temperature compensation of conductivity measurement
nLF Non-linear function for natural waters according to EN 27888
(ISO 7888), ground, surface and drinking water
Lin Linear temperature compensation
Compensation coefficient (only if t.Cor = Lin)
0.300 3.000 Temperature compensation coefficient in %/K

H72.0.11.6C-04 Operating Manual GMH 3451 page 10 of 18
_____________________________________________________ _____________________________________________________________________________
Menu Paramete
r
V
alue Description
or
Reference temperature of temperature compensation (only if t.Cor = Lin or nLF)
25 °C / 77 °F Reference temperature 25 °C / 77 °F
20 °C / 68 °F Reference temperature 20 °C / 68 °F
Adjustment/Calibration: Adjustment reminder period (factory setting: oFF)
1 …730 Adjustment reminder period (in days)
oFF No adjustment reminder
Auto Hold: Automatic measuring value identification (only if Logger = oFF)
on Auto measuring value identification (only if Logger = oFF) Auto Hold
oFF Standard hold function on key press (only if Logger = oFF)
Auto Power-Off : Selection of power-off delay
1...120 Power-off delay in minutes.
Device will be automatically switched off as soon as this time has
elapsed if no key is pressed/no interface communication takes place.
oFF Automatic power-off function deactivated (continuous operation)
Set Output: Configuration of universal output
oFF Interface and analogue output off -> minimal power consumption
SEr: Serial interface activated
dAC: Analogue output activated
01,11..91 Base address for serial interface communication
0.0 µS/cm ..
400 mS/cm Measuring value that should correspond to output 0 V
e.g. for 0.0 µS/cm
0.0 µS/cm ..
400 mS/cm Measuring value that should correspond to output 1 V
e.g. for 100.0 mS/cm
Set Corr: Measurement correction **
Zero point adjustment / offset of temperature measurement **
oFF No zero point adjustment for temperature measurement
-5.0 … 5.0°C Offset of temperature measurement in °C
Slope adjustment of temperature measurement **
oFF No slope adjustment for temperature measurement
-5.00 … 5.00 Slope correction of temperature measurement in [%]
Set Alarm: Confi
g
uration of alarm function
On / No.So Measuring channel cond/ rES /TDS/ SAL: alarm on with buzzer /
without buzzer
OFF No alarm function for measuring channel cond/ rES/ TDS/ SAL
0.0 µS/cm ..
400 mS/cm Min-alarm limit for cond/ rES/ TDS/ SAL (not if AL. 1. oFF)
0.0 µS/cm ..
400 mS/cm Max-alarm limit for cond/ rES/ TDS/ SAL (not if AL. 1. oFF)
On / No.So Temperature measurement: alarm on with buzzer / without buzzer
OFF No alarm function for temperature measurement
-5.0 ..+100.0 °C Min-alarm limit for temperature (not if AL. 2. oFF)
-5.0 ..+100.0 °C Max-alarm limit for limit temperature (not if AL. 2. oFF)
Set Lo
gg
er: Confi
g
uration of lo
gg
er function **
Selection of logger function *
oFF No logger activated
Sto
r
Store: Manual recording
CYCL Cyclic: Cyclic logger
0:01... 60:00 Cycle time in [minutes:seconds] (for cyclic logger)
**
Set Clock: Settin
g
of real time clock
HH:MM Clock: set time hours:minutes
YYYY Year: set year
TT.MM Date: set date day.month
rEAd CAL: Read calibration data:
see chapter 12.2 Calibration storage (rEAd CAL)

H72.0.11.6C-04 Operating Manual GMH 3451 page 11 of 18
_____________________________________________________ _____________________________________________________________________________
(*) If logger memory contains data sets parameters marked with (*) cannot be called. You have to clear memory to
change these parameters!
(**) If logger is running parameters marked with (**) cannot be called.
8 Data Logger
No logger operation possible with auto-range! The measuring range has to be selected
explicitly – see chapter 7 “Configuration“ -
The device supports two different logger functions:
“Func-Stor”: Manual recording by key press “store”
Additional input of measuring point (L-Id) is needed
“Func-CYCL”: Automatic recording at intervals of set cycle time
The logger stores 2 measuring values per data set.
One data set consists of: meas. value cond/ rES/ TDS/ SAL (one of them)
meas. value temperature
measuring point L-Id (only for “Func-Stor”)
time and date (when data set is saved)
For the evaluation of the data the software GSOFT3050 (version V3.0 or higher) has to be used. The
software also allows easy configuration and starting of the logger.
When the logger is activated (Func Stor or Func CYCL) the hold function is no more available, the key
“store” is solely used for the operation of the logger functions.
8.1 Manual recording (“Func-Stor”)
a) Save measurements manually:
Up to 1000 measurements can be saved if logger function “Func store” is selected. (see “Configuration”):
Press “Store” shortly: data set is saved (“St. XX” is displayed shortly,
where XX is the number of the data set)
Input of the measuring point “L-Id”: Selection of measuring point via keys or .
Number 0…19999 or text assigned to number 1…40
(comfortable assignment of texts can be done with gratis software GMHKonfig)
Confirm input with .
If logger storage is full, the following is displayed:
b) Read manual recordings:
Saved data sets can be viewed both with PC-software GSOFT3050 and directly on the device display.
Press “menu” for 2 seconds: is displayed
“rEAd LoGG” is only displayed if data sets have been already stored! Otherwise the
configuration menu is displayed:
Press shortly: Change between measuring values, measuring point and date+time
of the currently selected data set
or Change between different data sets
Quit display of recordings

H72.0.11.6C-04 Operating Manual GMH 3451 page 12 of 18
_____________________________________________________ _____________________________________________________________________________
c) Clear manual recordings:
If data sets have been stored, they can be deleted with the “store” key:
Press “store” for 2 seconds: Call menu “Clear”
Select with: or .
Clear nothing (cancel)
Clear all data sets
Clear the latest data set
Confirm selection and quit menu “Clear”
8.2 Automatic recording with selectable cycle time “Func CYCL”
If logger function “Func CYCL” is selected (see “Configuration”) the device will automatically record
measuring values at intervals of the set cycle time.
The logger’s cycle time can be set from 1s to 60min (see “Configuration”).
Up to 10000 measurements can be saved if logger function “Func CYCL” is selected.
a) Start recording:
Press “store” for 2 seconds: Start menu, press again: automatic recording is started
Each storage process is signalled by shortly displaying “St.XXXX”, where XXXX is the number of the
saved data set.
If the logger memory is full, the recording stops automatically and the display shows
b) Stop recording:
Press “store” for 2 seconds: If recording is running the “stop” menu is displayed
Select with or .
Do not stop recording (cancel)
Stop recording
If recording is running the “stop” menu is displayed
If you try to switch off the device while cyclic recording is active you will be asked
whether the recording should really be stopped.
The device can only be switched off if the recording is stopped. Auto-off function is
deactivated as long as cyclic recording is active.
c) Clear recordings:
Press “store” for 2 seconds:
If there are data sets stored and recording is already stopped the menu “Clear” is displayed
Select with or .
Do not stop recording (cancel)
Clear all data sets
Clear latest data set
Confirm selection and quit menu “Clear”

H72.0.11.6C-04 Operating Manual GMH 3451 page 13 of 18
_____________________________________________________ _____________________________________________________________________________
9 Universal output
The output can be used as serial interface (for USB 3100, USB 3100 N, GRS 3100 or GRS 3105
interface adapters) or as analogue output (0-1V).
If none of both is needed, we suggest to switch the output off, because battery life then is extended.
When operating with external supply or connected interface and measurement at solutions
with earth connection, there may appear distortions or deviations of the measuring. In case of
doubt disconnect supply/interface.
The same is valid for the analogue output: Depending how the output is connected (e.g. even
without isolation), in case of doubt do not measure in solutions with earth contact.
9.1 Serial Interface
By means of the serial interface and a suitable electrically isolated interface adapter (USB 3100, USB 3100
N, GRS 3100 or GRS 3105) the device can be connected to a computer for data transfer.
With the GRS 3105 up to 5 devices of the GMH3xxx- series can be connected to one interface (see also
manual of GRS 3105). As a precondition the base addresses of all devices must not be identical, make sure
to configure the base addresses accordingly (refer menu point “Adr.” in chapter 1 “Configuration“).
To avoid transmission errors, there are several security checks implemented e.g. CRC.
The following standard software packages are available:
GSOFT3050: Operation and read out of logger function for devices with integrated data logger
GMHKonfig: Software for a comfortable editing of the device (e.g. Material selection…)
EBS 20M / 60M: 20-/60-channel software to display the measuring values
In case you want to develop your own software we offer a GMH3000-development package including:
A universally applicable Windows functions library ('GMH3000.DLL') with documentation that can be
used by the most programming languages. Suitable for Windows XP™, Windows Vista™, Windows 7™,
Windows 8 / 8.1™, Windows 10™
Programming examples Visual Studio 2010 (C#, C++ und VB), Testpoint™,LabView™ uvm.
In addition to the operation at a PC the device can be operated with the GAM 3000 device, to use the alarm
function for simple supervision and controlling applications. Just connect a GAM 3000 to the interface,
activate the alarm function of the GMH and the relays output is operating.
The device has 2 channels:
- Channel 1: current measuring value Cond, rES, TDS oder SAL (base address)
- Channel 2: temperature value
Supported functions:
1 2 Code Name/Function 1 2 Code Name/Function
x x 0 Read measurement value x x 200 Read min display range
x x 3 Read system state x x 201 Read max display range
x 12 Read ID number x x 202 Read display range - unit
x x 22 Read min alarm rail (AL. - AL.Lo) x x 204 Read display range - decimal point
x x 23 Read max alarm rail (AL. - AL.Hi) x 208 Read # of channels
x x 176 Read min measuring range x 222 Read power off time (Conf-P.oFF)
x x 177 Read max measuring range x 223 Set power off time (Conf-P.oFF)
x x 178 Read measuring range unit x 233 Read real time clock (CLOC)
x x 179 Read measuring range decimal point x 234 Set real time clock (CLOC)
x x 180 Read kind of measuring of sensor x 240 Reset
x x 199 Read kind of measuring of display x 254 Program version
The measuring-/ alarm- and display range values read back from the interface are
always in the selected measurement unit!
When using the interface, the auto-range-function should be turned off. If auto-range is
activated, the returned value ar based on the resolution of the smallest ranges, there
may be returned extreme values like 123400.0 µS/cm instead 123.4 mS/cm.

H72.0.11.6C-04 Operating Manual GMH 3451 page 14 of 18
_____________________________________________________ _____________________________________________________________________________
9.2 Analogue Output
An analogue voltage 0-1V can be tapped at the universal output socket (mode: “Out dAC”).
With the DAC.0 and DAC.1 values the output can be rapidly scaled to your efforts.
Keep in mind not to connect low-resistive loads to the output, otherwise the output value will be wrong and
battery life is decreased. Loads above ca 10kOhm are uncritical.
If the display exceeds the value set by DAC.1, then the device will apply 1V to the output
If the display falls below the value set by DAC.0, then the device will apply 0V to the output
In case of an error (Err.1, Err.2, no sensor, etc.) the device will apply slightly above 1V to the output.
plug wiring:
GND
+Uout
Attention!
the 3rd contact has to be left floating!
Only stereo plugs are allowed!
10 Adjustment of temperature input
The temperature input can be adjusted with offset and scale. A reasonable adjustment presumes reliable
references (e.g. ice water, controlled precision water bath, etc.).
If the inputs are adjusted (i.e. offset and scale are different from default settings) the device will shortly
display “Corr” after turned on.
Default setting for offset and scale are ‘off’ = 0.0, i.e. inputs are not changed.
Zero point correction: Displayed value = measured value – OFFS
Zero point and slope correction: Displayed value = (measured value – OFFS) * (1 + SCAL / 100)
Displayed value °F = (meas. value °F - 32°F - OFFS) •(1 + SCAL / 100)
11 Automatic adjustment/calibration of cell correction
Besides the direct input of the cell correction (see below) via the menu (“CELL Corr”) the cell correction can
also be determined automatically:
Manual adjustment or Adjustment with reference solution
Menu selection: “CAL Edit” “CAL rEF.S”
Menu selection of desired solution
1413 µS/cm 0.01 M KCL
2.76 mS/cm 0.02 M KCL
12.88 mS/cm 0.1 M KCL
50 mS/cm KCL
111.8 mS/cm 1 M KCL
Values for 25°C, the temperature
dependency of those solutions are known
by the device and are compensated
automatically.
Press Cal-key for 2 s,
start of calibration “actual value” e.g. “1723 µS/cm” “value of solution” e.g. “1413 µS/cm”
and CAL with rotary symbol and CAL with rotary symbol
Calibration
Select desired display value wait until device measures stable value
with buttons “up” and “down”
and confirm with “enter”
Afterwards the device returns to the normal measuring operation mode or – if so – displays an error
message.
The resulting cell correction can be seen in the menu at “CELL Corr” and the calibration history.

H72.0.11.6C-04 Operating Manual GMH 3451 page 15 of 18
_____________________________________________________ _____________________________________________________________________________
Error messages of automatic adjustment/calibration:
CAL Err.1 Cell correction too high Determined cell correction must not exceed 1.2
CAL Err.2 Cell correction too small Determined cell correction must not fall below 0.8
CAL Err.3 Solution of wrong range Wrong solution / far beyond tolerance
CAL Err.4 Wrong temperature Beyond permitted temperature:
0.0 – 34.0 °C (or 0.0 – 27.0 °C at 111.8 mS/cm)
Alternative to automatic adjustment:
Manual calculation of cell correction with a reference solution
Example KCl-solution c= 0.01 M: 1413 μS cm-1 at 25°C
At other temperatures switch temperature compensation off (t.Cor = oFF) and use the referring conductivity!
Conductivity displayed = 1500 μS cm-1 if selected cell correction is 1.000 cm-1 (CELL Corr = 1.000)
Conductivity of solution at solution temperature 25 °C: Conductivity real = 1413 μS cm-1
Cell correction c = conductivity real / conductivity displayed [cm-1]
= 1413 / 1970 * cm-1 = 0.942 cm-1 (Enter CELL Corr of 0.942)
12 GLP
GLP (Good Laboratory Practice) includes regular check of devices and accessories. For pH measurements it
is highly important to ensure correct pH calibration. The device provides the following functions to help with
this.
12.1 Calibration interval (C.Int)
You can input the interval after which the device reminds you to recalibrate.
The interval times should be chosen according to the application and the stability of the electrode. “CAL”
flashes on the display as soon as the interval has expired.
12.2 Calibration storage (rEAd CAL)
The last 16 calibrations are stored with results and date and can be read out.
Display calibration data:
Historical calibration data can be comfortably read out via PC software GMHKonfig and GSOFT3050 or
displayed directly at the device:
Press for 2 seconds:
The display will show: or (configuration level)
Press several times until this is
displayed: read cal. = “read calibration data”
Press shortly: switch between:
- CELL = cell correction
- C.rEF = reference value, at which cell correction has been adjusted
- Display of date+time of data set
or Change between the different calibration data sets
Quit calibration data set display
13 Alarm („AL.“)
There are 3 possible settings:
off (AL.oFF), on with buzzer (AL.on), on without buzzer (AL.no.So).
Alarm is given in the following cases (if alarm active, AL.on or AL.no.So):
-Lower alarm boundary (AL. Lo) under-run
-Upper alarm boundary (AL. Hi) over-rum
-Sensor error
-Low battery (bAt)
-Err.7: system error (always with buzzer!)
In case of an alarm (and when polling the interface) the ‘PRIO’-flag is set in the returned interface message.
4
Set
Menu
4
Set
Menu
3
CAL
2
max
5
min

H72.0.11.6C-04 Operating Manual GMH 3451 page 16 of 18
_____________________________________________________ _____________________________________________________________________________
14 Real Time Clock (“CLOC”)
The real time clock is used for chronological assignment of the logger data and calibration points. Please
check the settings when necessary.
15 Accuracy Check / Adjustment Service
You can send the device to the manufacturer for adjustment and inspection.
Calibration certificate - DKD certificate - official certifications:
If the measuring instrument is supposed to receive a calibration certificate, it has to be sent to the
manufacturer (declare test points).
If the device is certificated together with a suitable sensor very high overall accuracies are possible.
Basic settings can only be checked and – if necessary – corrected by the manufacturer.
A calibration protocol is enclosed to the device ex works. This documents the precision reached by the
production process.
16 Error and System Messages
Error messages for measurement
Description What to do?
No display or
confused
characters,
Device does not
react on key press
Battery empty Replace battery
Mains operation: wrong voltage or polarity Check power supply, replace it if necessary
System error Disconnect battery and power supply, wait shortly,
then reconnect
Device defective Return to manufacturer for repair
Err.1 Measured value above allowable range Check: pressure not within sensor range?
-> measuring value to high!
Sensor defective Return to manufacturer for repair
Err.2 Measured value below allowable range Check: pressure not within sensor range?
-> measuring value to low!
Sensor defective Return to manufacturer for repair
Err.7 System error Return to manufacturer for repair
Value extremely out of measuring range Value extremely out of measuring range
----
Could not calculate display value
• measuring range or input range
exceeded
Check range parameter
• measured values are instable Wait for signal regulation of the device
> CAL <
CAL flashing in
upper display
Either preset calibration interval has
expired or last calibration is not valid
Device has to be calibrated!
NO . AVTO
LO66 RAN6
Logger could not be started Auto range for the display range is active
=> change the parameter in the configuration menu
Error messages for automatic cell correction adjustment/calibration:
CAL Err.1 Cell correction too high Determined cell correction must not exceed 1.2
CAL Err.2 Cell correction too small Determined cell correction must not fall below
0.8
CAL Err.3 Solution of wrong range Wrong solution / far beyond tolerance
CAL Err.4 Wrong temperature Beyond permitted temperature:
0.0 – 34.0 °C (or 0.0 – 27.0 °C at 111.8 mS/cm)
If “bAt” is flashing the battery will be exhausted soon. Further measurements are possible for short time. If
“bAt” is displayed continuously the battery is ultimately exhausted and has to be replaced. Further
measurements aren’t possible any more.

H72.0.11.6C-04 Operating Manual GMH 3451 page 17 of 18
_____________________________________________________ _____________________________________________________________________________
17 Reshipment and Disposal
17.1 Reshipment
All devices returned to the manufacturer have to be free of any residual of measuring media
and other hazardous substances. Measuring residuals at housing or sensor may be a risk for
persons or environment
Use an adequate transport package for reshipment, especially for fully functional devices.
Please make sure that the device is protected in the package by enough packing materials.
17.2 Disposal instructions
Batteries must not be disposed in the regular domestic waste but at the designated collecting
points.
The device must not be disposed in the unsorted municipal waste! Send the device directly to us
(sufficiently stamped), if it should be disposed. We will dispose the device appropriate and
environmentally sound.

H72.0.11.6C-04 Operating Manual GMH 3451 page 18 of 18
_____________________________________________________ _____________________________________________________________________________
18 Specification
Measuring
ranges
Anzahl 5
Conductivity 1 *) 0,0 ... 200,0 µS/cm
” 2 *) 0 ... 2000 µS/cm
” 3 *) 0,00 ... 20,00 mS/cm
” 4 *) 0,0 ... 200,0 mS/cm
” 5 *) 0 ... 400 mS/cm
Resistivity 0,005 ... 100,0 kOhm*cm
TDS 0,0 ... 1999 mg/l
Salinity 0,0 ... 70,0 g/kg (PSU)
Temperature -5,0 ... +100,0 °C
23,0 ... 212,0 °F
Accuracy Conductivity ±0,5% v.MW ±0,3 % FS or ±2 µs/cm
Temperature ±0,2 K
Connections Conductivity/
Temperature
Permanently connected measuring cell
Interface
Analogue output
Serial interface (3.5mm jack) can be connected to USB or RS232 interface of a PC
via electrically isolated interface adapter USB3100, USB 3100 N, GRS3100 or
GRS3105 (see accessories). Alternative selectable analogue output 0-1V
Measuring cell Four-electrode-conductivity-measuring cell with integrated temperature sensor
Electrode material special graphite
Shaft material epoxy
Size dia. 12 mm, length 120 mm
Ambient condition -5 … +80°C (continuous) up to +100°C (short-duration)
Display 4 digit 7-segment (main and secondary display) with additional symbols
Additional functions Min / max / hold
Adjustment/Calibration Cell correction manually or automatically via selectable reference solution
Data logger Real-time clock
Cyclic: 10000 data sets, cycle time selectable: 1s … 60 min
Single: 1000 data sets (with measuring point input, 40 selectable measuring point
texts or numbers)
Alarm 2 alarm channels with separate limit values for conductivity (or resistivity, TDS, SAL)
and temperature
Alerting: buzzer / visual / interface
Housing Break-proof ABS housing
Protection class Front side IP65
Dimensions
L*W*H [mm]
142 x 71 x 26 mm (L x W x H)
Working conditions -25 to 50 °C; 0 to 95 % RH (non condensing)
Storage temperature -25 to 70 °C
Power supply 9V-battery, typ IEC 6F22 (included in scope of supply) or external
Current
consumption
2 mA (Out = Off)
Battery indicator Automatically if battery exhausted and ’ bAt ’
Auto-Off-Function Device will be automatically switched off if no key is pressed/no interface
communication takes place for the time of the power-off delay. The power-off delay
can be set to values between 1and 120 min.; it can be completely deactivated.
Directives and standards The instruments confirm to following European Directives:
2014/30/EU EMC Directive
2011/65/EU RoHS
Applied harmonized standards:
EN 61326-1 : 2013 emissions level: class B
emi immunity according to table 3 and A.1
Additional fault: <1%