Bticino Sfera video kit Operating manual

User and installation manual
www.bticino.com
Sfera Keypad Module
353000

Sfera Keypad Module
User and installation manual

3
Contents
Sfera Keypad Module
User and installation manual
3
General information 4
Warnings and recommendations 5
Regulatory warnings 5
Front view 6
Back view 7
Installation 8
Mounting 8
Disassembling 10
Use of the device 12
Door lock control 12
Door lock control with stand-alone Keypad Module 353000 12
Door lock control with Sfera Speaker Module
351100/351200/351300 and Keypad Module 353000 12
Direct call with Sfera Speaker Module 351100/351200/351300
and Keypad Module 353000 13
Device configuration 14
Administrator code 14
New administrator code 14
Deleting administrator codes 17
Passepartout code 18
New passepartout code 18
Deleting administrator codes 21
Replacement of passepartout codes 22
Resident code 24
New resident code 24
Deleting resident codes 27
Replacing resident codes 29
Reset 31
Configuration using the software 32
Connection to the PC 32

4
Sfera Keypad Module
User and installation manual
General information
The Sfera Keypad Module must be used only on BTicino 2 wires digital systems.
Finishes that can be associated to the BTicino Sfera Keypad Module:
Front cover 353005
Front cover 353001/02/03
Front cover 353011

54
Sfera Keypad Module
User and installation manual
Warnings and recommendations
It is important to read this manual carefully before proceeding with the installation.
The warranty becomes automatically void in case of negligence, improper use, tampering by
unauthorised personnel.
Regulatory warnings
Read carefully before use and keep for future reference
Touching the units with wet hands is forbidden
Using liquid cleaners or aerosols is forbidden
Blocking the ventilation openings is forbidden
Modifying the devices is forbidden
Removing protective parts from the devices is forbidden
Installing the units near liquids and powders is forbidden
Installing the units near heat sources is forbidden
Installing the units near harmful gases, metal dusts or similar is forbidden
Fastening the units on unsuitable surfaces is forbidden
Risk of devices falling because the surface on which they are installed collapses
or inappropriate installation.
Switch the power supply OFF before any work on the system
Caution: Installation, configuration, starting-up and maintenance must be
performed exclusively by qualified personnel.
Check that the wall installation has been carried out correctly
Lay out the wires respecting the standards in force
Connect the power supply wires as indicated
Use only the items indicated in the technical specifications for any system
expansions

6
Sfera Keypad Module
User and installation manual
1
2
3
4
5
1. Digital keypad + key illumination LED.
key for the selection of the door lock
release code
key for the replacement of the codes.
2. Mini-USB programming connector.
3. Programming pushbutton..
4. Red LED on steady: access denied, or
programming error
5. Green LED on steady: access granted, or
programming successful
Front view

76
Sfera Keypad Module
User and installation manual
6
2 13
5
4
Back view
1. Connection of door lock pushbutton (CP-
P1) and tamper (CP-P2 – future application).
2. Local relay contacts.
3. Connection to the BUS.
4. Connector for the connection to
subsequent modules.
5. Connector for the connection to previous
modules.
6. Configurator sockets.

8
Sfera Keypad Module
User and installation manual
1
2
3
Installation
Caution: Installation, configuration, starting-up and maintenance must be performed
exclusively by qualified personnel.
Mounting

98
Sfera Keypad Module
User and installation manual
4
5
6

10
Sfera Keypad Module
User and installation manual
7
8
9
10
Disassembling
1
2
3
4

1110
Sfera Keypad Module
User and installation manual
5
5
7
8
6

12
Sfera Keypad Module
User and installation manual
STAND-ALONE
KEYPAD MODULE DOOR LOCK SHORT OPENING CODE MAX. OPENING CODE
Door lock connected
to the C/NO/NC local
relay of the keypad
module
SPEAKER MODULE +
KEYPAD MODULE DOOR LOCK SHORT OPENING CODE MAX. OPENING CODE
Door lock connected
to the S+ S- contact of
the speaker module
Door lock connected
to the C/NO/NC local
relay of the keypad
module*
* To use this function, make sure that the keypad module is configured with M=3 or M=23
Use of the device
The BTicino Sfera Keypad Module allows residents to open a door lock through the recognition of
previously stored numerical codes.
The device consists of a backlit pushbutton panel with 12 keys and LEDs to control the correct
entry of the code.
When combined with speaker module item 351100/351200/351300 and appropriately configured,
it also allows direct call.
Note: This manual refers to the Sfera wired stand-alone Keypad Module or paired with the Sfera Speaker
Module (351100/351200/351300).
If the Sfera Keypad Module is installed linked to the Display Module (352500) refer to the Display
manual for the code programming.
Caution: the secret code must consist of a minimum of 4 to a maximum of 9 digits.
Door lock control
he TiSferaDesign software can be used to set the maximum number of digits of the code (min. 4 to
max. 9).
Entering the codes to open the door lock varies depending on the code length (if it is shorter than
or the same as the maximum set) and the type of installation.
The correct form to use in the specific cases is shown in the tables below.
Door lock control with stand-alone Keypad Module 353000
Door lock control with Sfera Speaker Module 351100/351200/351300 and Keypad
Module 353000
The link between a Sfera Speaker Module and the Keypad Module allows the management of two
door locks. The table below shows how to use the codes correctly.
Note : the local relay closing time of the Keypad module is 4” and cannot be modified.

1312
Sfera Keypad Module
User and installation manual
SPEAKER MODULE +
KEYPAD MODULE CALL CODE
To use this function, make sure that the keypad module is configured with M=20 or M=23
Direct call with Sfera Speaker Module 351100/351200/351300 and Keypad Module
353000
Linking the Sfera Speaker Module and the Keypad Module allows direct call to an internal unit
using the code. Enter the call code, 1 to 4 digits, between 0 and 3999.
The table below shows how to use the codes correctly.

14
Sfera Keypad Module
User and installation manual
Device configuration
It is possible to program three different types of codes:
ADMINISTRATOR Code granting access to the programming of the other codes.
This code has programming rights, but not access rights..
PASSEPARTOUT This code allows the opening of the door lock to which the entrance panel is
associated.
It is not connected with any apartments.
This code has access rights, but no programming rights.
RESIDENTS This code allows the opening of the door lock to which the entrance panel is
associated.
It’s linked to an apartment of the system.
This code has access rights, but no programming rights.
Ha solo diritto di accesso e non di programmazione.
The configuration can be performed in two ways:
- using thel TiSferaDesign software
- following specific procedures using the keypad
For the configuration of the administrator codes, remove the front cover and press the
programming button highlighted in the legend.
1 2
Administrator code
The “ADMINISTRATOR” code is required for safety reasons, and is directly programmed by the
installer. The code grants access to the programming of the other codes (passepartout and
residents).
In order to access programming mode, it will be necessary to assign an administrator code to the
device. It is possible to save up to 20 administrator codes.
The keypad module will indicate if the code is accepted or rejected through audible signals and
the switching on of the green LED. Entering an unrecognised code will cause the interruption of
the programming procedure. This interruption will be notified with an extended beep and the
switching on of the red LED.
Note : only with Sfera Speaker Module 351100/351200/351300 + the associated Sfera Pushbutton
Modules 352000/352100 or only with the Sfera Keypad Module.
New administrator code
1. Press and hold down the programming pushbutton until the green LED starts flashing and a
confirmation tone is heard..
2. Press the key

1514
Sfera Keypad Module
User and installation manual
3
4
5
3. Enter the code (4 to 9 digits).
4. Press the
key
A short beep confirms the programming of the new administrator code.
5. Re-enter the code to confirm
Exact code: Green LED ON and short beep.
Wrong code: Red LED ON and long beep.

16
Sfera Keypad Module
User and installation manual
6
6. If the procedure is successful, the green LED stays on for approximately 1 second and then
starts flashing again.
Enter another code or end the procedure.
Press and quickly release the programming pushbutton, or wait 30 seconds to exit the
programming procedure.
A short beep and the switching off of the LED indicates that the programming sequence is
complete.
The Sfera Keypad module is ready for normal operation.
During the programming procedure, it will be necessary to follow some rules:
- keys must be pressed in succession (with maximum 2 seconds in between pressures).
- the programming sequence must start within 30 seconds from the pressure of the
programming button, and must be completed in one stage.

1716
Sfera Keypad Module
User and installation manual
1
2
1. Press and hold down the programming pushbutton; the green LED starts flashing.
2. Press and hold down the button; the device emits 1 beep per second and a long beep after 10
seconds.
Deleting administrator codes
The red LED flashes and then switches on to confirm that the deletion is complete.
The procedure will cancel all the saved administrator codes.
Press and hold down the programming button during the whole procedure.
To stop the deletion procedure release the programming pushbutton.
For selective deletion use the TiSferaDesign software.

18
Sfera Keypad Module
User and installation manual
3
2
1
1. Enter the administrator code.
The device emits a confirmation beep and the green LED flashes The programming stage has
started.
2. Press the key
3. Enter the passepartout code (4 to 9 digits)
Passepartout code
To access the programming of a“Passepartout” code, it will be necessary to have an administrator
code; it is possible to program up to 20 passepartout codes.
The keypad module will indicate if the code is accepted or rejected through audible signals and
the switching on of the green LED. Entering an unrecognised code will cause the interruption of
the programming procedure. This interruption will be notified with an extended beep and the
switching on of the red LED.
Note : only with Sfera Speaker Module 351100/351200/351300 + the associated Sfera Pushbutton
Modules 352000/352100 or only with the Sfera Keypad Module.
New passepartout code

1918
Sfera Keypad Module
User and installation manual
5
4
5. Re-enter the code to confirm
Exact code: Green LED ON and short beep.
Wrong code: Red LED ON and long beep.
4. Press the key
A short sound confirms the programming of the new passepartout code.

20
Sfera Keypad Module
User and installation manual
6
6. If the procedure is successful, the green LED stays on for approximately 1 second and then
starts flashing again.
Enter another code or end the procedure.
Press and quickly release the programming pushbutton, or wait 30 seconds to exit the
programming procedure.
A short beep and the switching off of the LED indicates that the programming sequence is
complete.
The Sfera Keypad module is ready for normal operation.
During the programming procedure, it will be necessary to follow some rules:
- keys must be pressed in succession (with maximum 2 seconds in between pressures).
- the programming sequence must start within 30 seconds from the pressure of the
programming button, and must be completed in one stage.