Grosvenor Sateon Advance I/O Blade User manual

Specifi cation
The Advance I/O Blade (Part No: SAT-ADV-BL-IO16) is
a plug-in unit that can be purchased with either the
Advance Single-Blade Controller (Part No: SAT-ADV-C-
SNG-IO) or the Advance Multi-Blade Controller (Part
No: SAT-ADV-C-MLT-IO).
Each I/O Blade enables the connection of up to 8
supervised inputs and 8 volt-free relay outputs.
Clearly labelled connectors simplify the task.
Overview Sateon Advance IO16 Blade
Aux Inputs 5V pullup (2k2), max 12V in
Aux Out 30V, 3A max
External Power Out (power limited) 12V, 500mA max
Operating Temperature 0 to +49°C (32 to 120°F)
Humidity 5-85±5% at 30±2°C (86±4°F)
Weight 185 g
Dimensions 197 x 60 x 28 mm
Sateon Advance I/O Blade
Installation Guide
Electromagnetic Compatibility
Following the provisions of EMC Directive 2014/30/
EU, this product complies with the following
standards:
EN 55022:2010 Class B
EN50130-4:2011 inc A1:2014
IEC 62599-2:2010
Page 1
WEEE
Please refer to www.grosvenortechnology.com/
legal-info/ for disposal instructions under EU
Directive 2012/19/EU.

Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
Out NO
Com
Out NC
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
GND
In +
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
sateon
I/O BLADE
0V
+12V
OUT
OUT
Auxiliary Input connections
The inputs are supervised and may optionally be used with line resistors
for fault detection.
Input
switch
1K
1K
GND
In +
1
Out NO
Com
Out NC
1
Normally Closed Contact
Common
Normally Open
The Auxiliary output relays off er volt free contacts and may be used to
connect to low voltage systems such as barriers or turnstiles, provided
the voltage across the contacts does not exceed 30V and current does
not exceed 3A.
Input switch
GND
In +
1
Contacts Only (no fault detection)
Supervised (short/open circuit detect)
Auxiliary Output connections
Inputs
1-8
Outputs
1-8
Power
out
The Aux input is pulled to 5V by the Blade using the equivalent
circuit shown below
Connections
Page 2
Power supply
12Vdc power supply
for connecting
associated devices.
+
Power Out
12 Vdc
0V
+12V
OUT
OUT
Supervised (short/open circuit detect)
Tamper
switch
1K
1K 2K2
Input
switch
GND
In +
1
Supervised (short/open circuit detect)

Power
The Advance I/O Blade draws 12V power from the
Controller.
The I/O Blade Power draw is summed as follows:
I/O Blade Quiescent Current = 83 mA max @12V
(1.0W)
I/O Blade Maximum Current (all AUX Output Inputs
grounded, all AUX Output relays active) = 333 mA
@12V (4.0W)
External 12V output (if used) = up to 500 mA max
@12V (6.0W)
Status LED
The main Blade LED Indicator is used to indicate
activity and state. See also the status LED on the
controller.
If the LED is continuously red, the Blade is not
communicating with the controller.
Blade State is reported by fl ashing a code on the LED
every 15 seconds as follows:
5 blue fl ashes Board is not being monitored.
Probably no download to
controller from Sateon
5 red fl ashes Wrong device type confi gured,
e.g. Door defi ned on an IO Blade
3 red fl ashes Out of range device confi gured
5 green fl ashes No devices confi gured for board
5 yellow fl ashes Reports electrical issues, such
as current tripped, over voltage,
under voltage, over current,
under current
Blade Activity is reported as follows:
Yellow fl icker (lasts
about 30 seconds)
Firmware download in
progress
Green blink (every 5
seconds)
Board running OK
Blue blink Read
Yellow blink Input state change
Red blink Output state change
Blade LED indicators
Notes
Page 3
Email: [email protected]
Telephone: [phone]
Web: www.grosvenortechnology.com
For more information about Sateon, visit the website or contact Technical Support: