Grotime Rollover User manual
ROLLOVER
5in 1cot to full size single bed
Two adults required to assemble this cot.
!
Themanufacturer's assembly instructions must be followed
in detail to ensure the safety features to thecotare not compromised.
!
This product is covered by a number of registered designs, trademarks and patents pending
2xEnd Panels
PB
1 x Fixed Side
PA
1 x Drop Side
PC
1 x Cot Base
PD
x2
Allen Key
HG
x8
Feet Pads
HH
x4
CAMDOCK
TM
Base Plates
HF
x12x32
16mm
Bolts
HA
70mmBolts
HB
x4
Guide Pins
HC
x4
Wood Screws
HD
HARDWAREINVENTORY
PRE-INSTALLEDHARDWARE
PARTS LIST
4 x BILATERAIL
TM Base Rails
PE
11 x Single Bed Slats
PF
2xBILATERAIL
TM Base Bracketss
PG
2
Oval Badges x 4 pcs with
40mm Bolts x 8 pcs
Locking Bolts
STEP1
ASSEMBLEFIXED SIDE TOENDS
STEP2
FIX FOUR CAMDOCK TM
BASE PLATES*
*Patent pending
HIGH
Bassinetlevel
LOW
Toddler level
Chose high or low
positionfor mattressbase
!
3
x4
70mmBolts
HB
FixedSide
PA
EndPanels
PB
x1 x2
Do not tighten bolts at this stage
!
x8
16mmBolts
HA
x4
CAMDOCK Base Plates
HF
Do not tighten bolts at this stage
!
TM
STEP 3
PLUG FINGER ENTRAPMENTS
STEP 4
PLACE COT BASE ON TOP OF BASE PLATES
4
x8
16mm Bolts
HA
1 x Cot Base
PD
STEP 5
ASSEMBLE COT BASE
STEP 6
SCREW FOUR GUIDE PINS INTO ENDS FIRMLY
5
x8
16mm Bolts
HA
x4
Guide Pins
HC
Screw Driver
Do not tighten bolts at this stage
!
STEP 7
ASSEMBLE DROP SIDE
Ensure correct side is facing out.
Align two access holes in the built-in
runner with the guide pins on one end.
Now repeat on other end.
!
STEP 8
FULLY SCREW IN LOCKING BOLTS
Lift drop side up until it clicks
into the locking position.
b.
a.
6
x1
Drop Side
PC
STEP 9
TIGHTEN ALL BOLTS
STEP 10
OPERATION
Base shown in Lower Position.
1.
2.
3.
To lower drop side, lift from centre of top rail, hold side in that position while using your leg to push inward on
centre of bottom rail. Then allow to slide gently down.
7
Remove dropside by reversing to step 5.
Day Bed
DAY BED CONVERSION
COT BED CONVERSION
Remove dropside by reversing to step 5.
a.
b.
8
Cot Bed
Remove dropside guide pins (HC) from the ends to prevent injury.
!
FULL SIZE SINGLE BED CONVERSION
STEP 1 Disassemble the cot following the
assemble instructions in reverse order.
Roll over cot ends on their sides
b.
a.
STEP 2
REMOVE FOUR GROTIME BADGES
9
Rollover action Patent Pending
10
STEP4
ASSEMBLE SINGLE BED BASE
Layone siderail down thenslotallslats intothe mortises.
Place the second side rail on top.
Working from one end slot all stats into the mortises.
STEP3
ASSEMBLE BILATERAIL
TM BED RAILS
Patent pending
Use the four wood screws to
r.
x2 x11
Assembled base rails
PE
Cot Bed Slats
PF
x4
WoodScrews
HD
Screw Driver
1.
2.
3.
Ensure the slat withthe warning labels is correctlypositioned
in the middleand the “this waydown” lable
is facingdown as directed by the
warning lableon therails.
!
x4 x2
BILATERAIL
TM Base Brackets
PG
BILATERAIL
TM BaseRails
PE
x8
mm Bolts
HE
20mm Insert Nut
HP
Align insert
sleeve so the slot
is facing out
Place insert sleeves
into base rail.
(2 at each end of rail)
x8
16
TIGHTEN ALL BOLTS
Your single bed is now complete.
11
STEP 6
ASSEMBLE SINGLE BED BASE BETWEEN TWO ENDSx8
70mm Bolts
HB
b.
a.
STEP 5
Use the four wood screws to
x the railsand slats together.
x4
Wood Screws
HD
Screw Driver
!
Adjust insert nut
clockwise/anticlockwise
sothatthreaded holes
ininsertnut align with bolt
holes in endof base rail
a.
b.
12
MAINTENANCE
Check your cot regularly. Retighten all bolts. For after sales service contact Grotime Service Australia on
1300 799 912; or New Zealand on 0508 476 932;
CONTACT US
AUSTRALIA - 10 Martini Parade Lithgow NSW 2790
NEW ZEALAND - 9 Greenacres Road North Richmond, Nelson 7050
RECOMMENDED MATTRESS SIZE
This cot has been manufactured for use with a mattress which measures 760mm in width and 1300mm in length and 130mm
in thickness. The width and length are specified because it is important that the gaps between the mattress and the sides and
ends of the cot will not exceed 40mm. This is to minimise the risk of the child’s limb becoming caught in the gap. The thickness
of the mattress has been specified to ensure that the depth of the cot is greater than 500mm with the mattress base in the lowest
position to minimise the risk of a child climbing or falling out of the cot.
5 YEAR NURSERY FURNITURE WARRANTY
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
In order for your claim to be processed in an efficient timely manner please follow the warranty claims process as out lined
below.
Fill in the online customer service form found on the following link
http://grotime.net/customer-service-form
If you are unable for any reason to process your warranty claim using the online customer service form please call our
In order for your claim to be processed you will need to provide to Grocorp with an original proof of purchase. For
example original retailer purchase receipt, bill of sale, invoice, lay-by docket, credit card receipt or similar proof of
purchase.
Note; providing attached photographs with your claim will greatly enhance the speed in which your claim is processed.
This warranty does not obligate Grocorp to bear transportation costs incurred in the repair or replacement of any defective
parts and excludes any superficial scratches, dents, scrapes or blemishes to paint work or timber surfaces. This Warranty
does not cover faults or defects caused by:
To the fullest extent permitted by law, Grocorp excludes all liability for damage or injury to any person, damage to any
property, and any indirect consequential or other loss or damage.
Unsuitable, improper use or use not in accordance with the manufactures specifications;
Incorrect installation or installation not in accordance with instructions provided;
Normal wear and tear;
Inadequate or complete lack of maintenance;
Chemical, electrochemical or electrical influences; or
Harsh detergents or abrasive cleaners used on product finishes.
WARNING
TO PREVENT FALLS, THE
MATTRESS BASE OF THIS
COT SHOULD BE ADJUSTED
TO THE LOWEST POSITION
BEFORE CHILD CAN SIT UP.
WARNING
ENSURE YOUR CHOSEN LOCATION FOR THE COT IS A REASONABLE DISTANCE FROM
CURTAINS, BLINDS, HEATERS, AND POWER POINTS. ALWAYS KEEP MEDICATION, STRING,
ELASTIC, SMALL TOYS OR SMALL ITEMS SUCH AS MONEY OUT OF REACH FROM ANY
POSITION IN THE COT.
BEFORE ASSEMBLING THE COT, ENSURE YOU HAVE A CLEAR AREA ON CARPET OR A THICK
BLANKET OR RUG. NEVER ASSEMBLE ON A HARD SURFACE.
12
•
1.
2.
3.
4.
•
•
•
•
•
•
•
•
•
Table of contents
Other Grotime Baby & Toddler Furniture manuals
