Grozone Control TV1 User manual

www.grozonecontrol.com
USER GUIDE
TV1
Temp-1V
Day & Night Fan Speed Control

SAFETY NOTICE 3
PRODUCT DETAILS 4
INSTALLATION & OPERATION 5
OPTIONAL SETTINGS/so control mode 6
OPTIONAL SETTINGS/ght control mode 7
QUICK TROUBLESHOOTING GUIDE 8-9
COMPLETE TROUBLESHOOTING GUIDE 10-11
WARRANTY & CUSTOMER SERVICE 12-13
TABLE OF CONTENTS

3
SAFETY NOTICE
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
DANGER
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
CAREFULLY FOLLOW THESE INSTRUCTIONS.
To reduce the risk of electric shock, disconnect power to the 120V
electrical outlet before installing or removing the unit. When removing the
electrical wall plate, it may fall across plug pins or become displaced.
To reduce the risk of electric shock, this product has a grounding type plug
that has a third (grounding) pin. This plug will only fit into a grounding
type power outlet. If the plug does not fit into the outlet, contact a
qualified electrician to install the proper outlet. Do not change the plug in
any way.

4
PRODUCT DETAILS
Operaon and Specificaons
Temperature setpoint between 55°F and 95°F / 13°C to 35°C.
Internal operaon in Fahrenheit.
The 120V output is variable. Max 750 Was, 6.2 Amps.
Fan is between 37% and 100% of full power on a 6°F range (Tight Control)
or 9°F range (So Control).
2 seconds «KickStart» at startup. (100% power to improve or ensure fan
startup).
6- temperature probe works from +32°F to +212°F (0°C to 100°C).
Electrical Specificaons: See the rang label on your product.

5
INSTALLATION & OPERATION
Note: This unit has been set to perform in Tight Control Mode. For
So Control Mode, refer to Oponal Sengs.
Adjusng temperature setpoints
Plug into 120 VAC outlet (see security noce on page 1).
Place the sensor at desired locaon.
Connect the fan into the front panel outlet (MAX 750W, 6.2A).
Night Temp
Day Temp
Installaon is now complete
Light sensor (photocell)

6
A. Unplug the unit.
Set both values to minimum.
OPTIONAL SETTINGS/SOFT CONTROL MODE
B. Within 5 seconds, plug in
the unit, then set both
values to maximum.
Changing to So Control Mode
TV1 is now in So Control Mode
For medium variaon and medium precision; use this mode when equipment
turns on and off repeatedly.

7
A. Unplug the unit.
Set both values to maximum.
B. Within 5 seconds, plug
in the unit, then set both
values to minimum.
TV1 is now in Tight Control Mode
OPTIONAL SETTINGS/TIGHT CONTROL MODE
Changing to Tight Control Mode
For smaller variaon and higher precision; use this mode for best performance
using correctly sized fan.

8
= Steps
Day
knob at
Max
QUICK TROUBLESHOOTING GUIDE
Product
Defecve
Day & Night
knobs at
Min
Product
Defecve
Night
knob at
Max
A
B
C
Quick Troubleshoong Chart Product Model: TV1
PLUG UNIT INTO 120V
PLUG FAN INTO OUTPUT*
Output On
Output
Off
Output Off
Output
Off Output On
DEFINITIONS
Min : Knob at 55°F or below Max : Knob at 95°F or above
Product
Defecve
Output
On

9
QUICK TROUBLESHOOTING GUIDE
Product
Defecve
Product
Defecve
Night
knob at
Min
Uncover photocell
& wait 10 sec
Cover
photocell with
hand palm &
wait 10 sec
D
E
F
H
Warm up
temp probe
in your
hand
Product
Defecve
Fan maintains speed or
slows down
I
TV1 &
probe
Good
*Before test, check if load is
working properly.
Rotate day knob from
Min toward Max slowly
unl fan slows down
Day
knob at
Min
Product
Defecve
Output
On Output Off
Output
Off Aer 10 sec
Output On
Output On
Output
Off
Fan speed up at full speed

10
COMPLETE TROUBLESHOOTING GUIDE
Day & Night Fan Speed Control
TV1
1 – Before you start
2 – Test
***IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS BEFORE
STARTING THE TEST.
· DO NOT CONNECT THE UNIT BEFORE STEP 1 OF THE TEST.
· CONNECT A FAN IN THE FRONT UNIT OUTPUT.
· LIGHTING CONDITION: perform this test in a room with enough light for
the controller to detect a DAY condion.
· TEMPERATURE: perform this test in a room where ambient
temperature is between 65°F and 85°F (18°C and 30°C).
· Definions : CW : Clockwise.
CCW : Counter clockwise.
STEP HANDLING AND TEST DESCRIPTION EXPECTED RESULTS
1 · Plug the unit into the power outlet.
· Turn UPPER knob fully CCW (55°F). The fan will turn ON.
2 · Turn UPPER knob fully CW (95°F). The fan will turn OFF.
3
· Turn LOWER knob fully CCW (55°F).
· Cover the Light Sensor completely
with hand palm or black electrical
tape (a single finger will NOT cover
the sensor appropriately).
The fan will turn ON
aer 6-8 seconds.