Grundfos WIO sensor User manual

WIO sensor
Installation and operating instructions
70x70
TM039726 1409
WIO sensor
Installation and operating instructions
Other languages
http://net.grundfos.com/qr/i/96591899
GRUNDFOS INSTRUCTIONS


English (GB) Installation and operating instructions
Original installation and operating instructions
Table of contents
1. General information ............. 5
1.1 Hazard statements .............. 5
1.2 Notes ..................... 5
2. Receiving the product............ 5
3. Installing the product ............ 6
3.1 Explosion-proof environments ........ 6
3.2 Mechanical installation ............ 6
3.3 Electrical connections............. 7
4. Starting up the product ........... 8
5. Product introduction ............ 8
5.1 Product description .............. 8
5.2 Applications .................. 8
5.3 Intended use ................. 8
6. Approvals .................. 9
6.1 Markings ................... 9
6.2 Approval standards, Europe ......... 9
6.3 Standards, IEC countries ...........10
6.4 Type key....................10
7. Servicing the product ............11
7.1 Replacing the product ............11
8. Technical data ................11
8.1 Operating conditions .............11
8.2 Electrical data .................11
8.3 Sensor signals ................11
9. Disposing of the product ..........11
4
English (GB)

1. General information
Read this document before you install the
product. Installation and operation must
comply with local regulations and accepted
codes of good practice.
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.
1.1 Hazard statements
The symbols and hazard statements below may
appear in Grundfos installation and operating
instructions, safety instructions and service
instructions.
DANGER
Indicates a hazardous situation which, if
not avoided, will result in death or serious
personal injury.
WARNING
Indicates a hazardous situation which, if
not avoided, could result in death or
serious personal injury.
CAUTION
Indicates a hazardous situation which, if
not avoided, could result in minor or
moderate personal injury.
The hazard statements are structured in the following
way:
SIGNAL WORD
Description of the hazard
Consequence of ignoring the warning
• Action to avoid the hazard.
1.2 Notes
The symbols and notes below may appear in
Grundfos installation and operating instructions,
safety instructions and service instructions.
Observe these instructions for explosion-
proof products.
A blue or grey circle with a white graphical
symbol indicates that an action must be
taken.
A red or grey circle with a diagonal bar,
possibly with a black graphical symbol,
indicates that an action must not be taken
or must be stopped.
If these instructions are not observed, it
may result in malfunction or damage to the
equipment.
Tips and advice that make the work easier.
2. Receiving the product
When receiving the product, check the following
points:
• The product corresponds to the order.
• The product is suitable for the actual supply
voltage.
• The product does not have any transport damage.
In case of any damage, contact the transporter
immediately.
5
English (GB)

3. Installing the product
Installation must be carried out by
Grundfos or an authorised service
workshop.
The free end of the permanently connected supply
cable must be connected by using a suitable certified
junction box or it must be connected outside the
explosive area.
CAUTION
Electric shock
Minor or moderate personal injury
‐Switch off the power supply before you
start any work on the product.
‐Make sure that the power supply
cannot be accidentally switched on.
When the sensor is re-fitted after oil change, it must
be cleansed by means of a solvent.
3.1 Explosion-proof environments
The control unit must protect the sensor:
1. The WIO sensor is approved according
to EN/IEC 60079-18. In Ex and IECEx
applications, the WIO sensor shall be
protected by an external current
limitation of 350 mA with a breaking
capacity of the maximum prospective
short circuit current of the supply. This
limited current must be provided by a
galvanic isolated power supply to the
sensor.
Note: As the IO 113 is equipped with
this current limitation and galvanic
isolated power supply, no further
protection is required when using an IO
113.
2. The sensor must always be installed in
such a way that it is protected against
mechanical damage and the possibility
for electrostatic charge.
3. The sensor must be installed
submerged in an oil chamber or similar
- not for use in air environment.
4. The sensor is protected using
protecting method "m" (EN/IEC
60079-18), "e" (EN/IEC 60079-7) and
"t" (EN/IEC 60079-31).
3.2 Mechanical installation
The mechanical installation depends on the pump
type and whether the wiring of the sensor in the pump
must be internal or external. See sections Internal
wiring, inside pump and External wiring, outside
pump.
However, the sensor must always be installed in such
a way that it is protected against mechanical damage
and the possibility for electrostatic charge. This will
typical be in the oil chamber or similar.
Related information
3.2.1 Internal wiring, inside pump
3.2.2 External wiring, outside pump
3.2.1 Internal wiring, inside pump
When sensors with internal wiring are to be replaced,
proceed according to the service instructions of the
pump in question.
It is important to ensure proper earth
connection between the metal housing of
the WIO sensor and the pump housing.
This is normally done through the holder
for the WIO sensor.
3.2.2 External wiring, outside pump
1. Fit the cable with a bush and an adapter for NPT
thread, typically 3/4".
2. Push the sensor into the oil chamber through the
filling hole and screw the bush into the thread. Do
not tighten the bush until the sensor is positioned
correctly in the pump.
3. Insert the sensor so far into the chamber that it is
completely submerged in the oil.
The product must not touch rotating
parts.
Ensure proper earth connection
between the screen of the cable and
the control cabinet.
6
English (GB)

3.2.3 EMC-correct installation
In the case of pumps with frequency converter it is
especially important to ensure an EMC-correct
installation.
The following rules must therefore be observed:
• The cable screen must be connected to earth.
• Screen ends must not be twisted as this will
destroy the screen effect at high frequencies. Use
cable clamps as shown in fig. 2.
• It is important to ensure a good electric contact
from the mounting plate through the mounting
screws to the metal cabinet of the frequency
converter.
• Use toothed washers and a galvanically
conducting mounting plate.
1
TM031080
Screen mounted with a cable clamp
Pos. Description
1Note the insulating plastic layer between
screen and sheath.
3.3 Electrical connections
Carry out the electrical connections according to local
regulations.
The conductors must be connected as shown in figs
Connection to the IO 113 and Connection of
conductors.
+ equals brown.
- equals white.
P1
BW
A
P2 P3 P4 P5 I1 I2 I3
ON DIP
1 2 3 4 5 6 7 8 9 10 11 12
TM066812
Connection to the IO 113
Pos. Description
W White
B Brown
A WIO sensor
VDC Rload
+
-
TM031391
Connection of conductors
Rload is the internal resistance of the connected
device, for instance IO 113.
The maximum load resistance plus the conductor
resistance can be calculated as follows:
Rload =
VDC -
10 [Ω]
0.022
7
English (GB)

4. Starting up the product
Startup must be carried out by authorised persons.
Switch on the power supply and check that the signal
is as expected, 4 mA for 0 % water. If the signal is ok,
the system is ready for operation.
5. Product introduction
5.1 Product description
3
2
1
59
12
TM031164
Water-in-oil sensor
Pos. Designation
1 Steel tube with sensor
2 Screen
3 Cable
5.2 Applications
The WIO sensor measures the water content in the
oil and converts the value into an analog current
signal. The two sensor conductors are for power
supply as well as for carrying the signal to the
measuring device or controller. The sensor measures
the water content from 0 to 20 %. It also sends a
signal if the water content is outside the normal range
(warning), or if there is air in the oil chamber (alarm).
The sensor is fitted in a stainless steel tube for
mechanical protection.
It also has also special operation state, if the sensor
is in air (no oil detected), or the water content is more
than the measurable level (>20%).
5.3 Intended use
The sensor is normally used together with the
Grundfos IO 113 module, but it can also be used
together with other controllers with inputs of 4 to 20
mA.
Operation with standard controllers will miss the
special air detection state (3,5mA output from WIO),
and over 20% water detected state (22mA).
Together with the IO 113, the sensor filters the signal
and provides an easy readout of the actual value.
Furthermore, it is possible to set a user-defined
warning limit and calibrate the IO 113 and the sensor
to the oil .
The IO113 gives special warning signal in case of air
detection (blinking yellow indicatior).
8
English (GB)

6. Approvals
The WIO sensor has been tested by DEKRA.
6.1 Markings
GRUNDFOS, WIO sensor 96XXXXXX PCXXXX-XXX, max. 24 VDC, 3.4 - 22 mA, Tamb 0 °C - 70 °C; KEMA
05ATEX2176X, II 2GD Ex eb mb IIC T4 Gb, Ex mb tb IIIC T135 °C Db, IECEx KEM05.0019X, CE0344,
IP68, BAS21UKEX0282X, UKCA 1180.
6.2 Approval standards, Europe
The sensor is approved as CE 0344/UKCA 1180 II 2 GD, Ex eb mb IIC T4 Gb, Ex mb tb IIIC T135 °C Db,
according to these standards: EN IEC 60079-0, EN 60079-7, EN 60079-18 and EN 60079-31.
Directive/standard Code Description
ATEX
UKEX
CE 0344
UKCA 1180
CE marking of conformity according to the ATEX directive 2014/34/EU,
Annex X. UKCA marking of conformity according to the UKEX regulation,
2016. 0344/1180 is the number of the Notified Body/Approved Body which
has certified the quality system for ATEX/UKEX.
The equipment conforms to harmonised EU and UK standards.
II Equipment group according to the ATEX directive/UKEX regulation, defining
the requirements applicable to the equipment in this group
2Equipment category according to the ATEX directive/UKEX regulation,
defining the requirements applicable to the equipment in this category
G Explosive atmospheres caused by gases, vapours or mists
D Explosive atmospheres caused by dust
Harmonised
European standard,
EN IEC 60079-0,
EN 60079-7,
EN 60079 18,
EN 60079-31
Ex Marking of explosion protection
eb Protection according to EN 60079-7
mb Encapsulation according to EN 60079-18
tb Protection by enclosure according to EN 60079-31
IIC Classification of gases, a typical gas is hydrogen
T4 Maximum surface temperature is 135 °C
Gb Suitable for use in gas atmospheres
IIIC Conductive dust
T135 °C Maximum surface temperature
Db Suitable for use in explosive dust atmospheres
9
English (GB)

6.3 Standards, IEC countries
The sensor is approved as Ex eb mb IIC T4 Gb, Ex mb tb IIIC T135 °C Db.
Standard Code Description
IEC 60079 0,
IEC 60079-7,
IEC 60079 18
IEC 60079-31
Ex Marking of explosion protection
eb Protection according to IEC 60079-7
mb Encapsulation according to IEC 60079-18
tb Protection by enclosure according to IEC 60079-31
IIC Classification of gases, a typical gas is hydrogen
T4 Maximum surface temperature is 135 °C
Gb Suitable for use in gas atmospheres
IIIC Conductive dust
T135 °C Maximum surface temperature
Db Suitable for use in explosive dust atmospheres
6.4 Type key
WIO sensor 96XXXXXX PCXXXX - XXX, max 24VDC, 3.4 - 22mA, Tamb 0 °C - 70 °C; KEMA 05ATEX2176X,
II 2GD Ex eb mb IIC T4 Gb, Ex mb tb IIIC T135 °C Db, IECEx KEM 05.0019X, BAS21UKEX0282X, IP68
1 2 3 4 5 6
8
710
0344
11
1180
9
TM066902
Pos. Description
1 Product name and part number
2 Production code PC, year and week
3 Serial number
4 Supply voltage
5 Temperature conditions
6 ATEX certificate number
7 EU QAN issuer number
8 UK QAN issuer number
9 Ex marking
10 IECEx certificate number
11 UK Ex certificate number
10
English (GB)

7. Servicing the product
The sensor requires no maintenance. The sensor is
self-cleaning and need no further cleaning.
7.1 Replacing the product
Replace the sensor in case of a sensor fault.
Replacement instructions can be found in
Grundfos Product Center at
www.grundfos.com.
WARNING
Electric shock
Death or serious personal injury
‐Before starting work on the product,
make sure that the fuses have been
removed or the main switch has been
switched off.
‐Make sure that the power supply
cannot be accidentally switched on.
8. Technical data
8.1 Operating conditions
Note: Always inform Grundfos if the WIO sensor has
been exposed to any harmful external effects or
aggressive substances.
Ambient temperature: 0-70 °C
Process temperature: 0-70 °C
Storage temperature: 0-80 °C
8.2 Electrical data
Input voltage: 12-24 VDC
Output current: 3.4 - 22 mA
Power consumption: 0.6 W
8.3 Sensor signals
4-20 mA 0-20 % water in oil
Accuracy better than 2 %
22 mA
Warning:
Water content far outside measuring
range
3.5 mA Alarm:
Air in the oil chamber
The sensor signal is only valid when oil
and water is mixed, when the pump is
running.
The sensor capability has been verified by
10W40 motor oil. Other types of oil may
have an impact of the measured value.
9. Disposing of the product
This product or parts of it must be disposed of in an
environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest
Grundfos company or service workshop.
See also end-of-life information at
www.grundfos.com/product-recycling.
The crossed-out wheelie bin symbol
on a product means that it must be
disposed of separately from household
waste. When a product marked with
this symbol reaches its end of life, take
it to a collection point designated by
the local waste disposal authorities.
The separate collection and recycling
of such products will help protect the
environment and human health.
11
English (GB)

Declaration of conformity
GB: EU declaration of conformity
We, Grundfos, declare under our sole responsibility
that the product WIO, to which the declaration below
relates, is in conformity with the Council Directives
listed below on the approximation of the laws of the
EU member states.
BG: Декларация за съответствие на EO
Ние, фирма Grundfos, заявяваме с пълна
отговорност, че продуктът WIO, за който се
отнася настоящата декларация, отговаря на
следните директиви на Съвета за уеднаквяване
на правните разпоредби на държавите-членки на
ЕO.
CZ: Prohlášení o shodě EU
My firma Grundfos prohlašujeme na svou plnou
odpovědnost, že výrobek WIO, na který se toto
prohlášení vztahuje, je v souladu s níže uvedenými
ustanoveními směrnice Rady pro sblížení právních
předpisů členských států Evropského společenství.
DE: EU-Konformitätserklärung
Wir, Grundfos, erklären in alleiniger Verantwortung,
dass das Produkt WIO, auf das sich diese Erklärung
bezieht, mit den folgenden Richtlinien des Rates zur
Angleichung der Rechtsvorschriften der EU-
Mitgliedsstaaten übereinstimmt.
DK: EU-overensstemmelseserklæring
Vi, Grundfos, erklærer under ansvar at produktet
WIO som erklæringen nedenfor omhandler, er i
overensstemmelse med Rådets direktiver der er
nævnt nedenfor, om indbyrdes tilnærmelse til EU-
medlemsstaternes lovgivning.
EE: EÜvastavusdeklaratsioon
Meie, Grundfos, kinnitame ja kanname ainuisikulist
vastutust selle eest, et toode WIO, mille kohta all
olev deklaratsioon käib, on kooskõlas Nõukogu
Direktiividega, mis on nimetatud all pool vastavalt
vastuvõetud õigusaktidele ühtlustamise kohta EÜ
liikmesriikides.
ES: Declaración de conformidad de la UE
Grundfos declara, bajo su exclusiva
responsabilidad, que el producto WIO al que hace
referencia la siguiente declaración cumple lo
establecido por las siguientes Directivas del
Consejo sobre la aproximación de las legislaciones
de los Estados miembros de la UE.
FI: EU-vaatimustenmukaisuusvakuutus
Grundfos vakuuttaa omalla vastuullaan, että tuote
WIO, jota tämä vakuutus koskee, on EU:n
jäsenvaltioiden lainsäädännön lähentämiseen
tähtäävien Euroopan neuvoston direktiivien
vaatimusten mukainen seuraavasti.
FR: Déclaration de conformité UE
Nous, Grundfos, déclarons sous notre seule
responsabilité, que le produit WIO, auquel se réfère
cette déclaration, est conforme aux Directives du
Conseil concernant le rapprochement des
législations des États membres UE relatives aux
normes énoncées ci-dessous.
GR: Δήλωση συμμόρφωσης ΕΕ
Εμείς, η Grundfos, δηλώνουμε με αποκλειστικά δική
μας ευθύνη ότι το προϊόν WIO, στο οποίο
αναφέρεται η παρακάτω δήλωση, συμμορφώνεται
με τις παρακάτω Οδηγίες του Συμβουλίου περί
προσέγγισης των νομοθεσιών των κρατών μελών
της ΕΕ.
HR: EU deklaracija sukladnosti
Mi, Grundfos, izjavljujemo s punom odgovornošću
da je proizvod WIO, na koja se izjava odnosi u
nastavku, u skladu s dolje navedenim direktivama
Vijeća o usklađivanju zakona država članica EU-a.
HU: EU megfelelőségi nyilatkozat
Mi, a Grundfos vállalat, teljes felelősséggel
kijelentjük, hogy a(z) WIO termék, amelyre az alábbi
nyilatkozat vonatkozik, megfelel az Európai Unió
tagállamainak jogi irányelveit összehangoló tanács
alábbi előírásainak.
IT: Dichiarazione di conformità UE
Grundfos dichiara sotto la sua esclusiva
responsabilità che il prodotto WIO, al quale si
riferisce questa dichiarazione, è conforme alle
seguenti direttive del Consiglio riguardanti il
riavvicinamento delle legislazioni degli Stati membri
UE.
LT: ES atitikties deklaracija
Mes, Grundfos, su visa atsakomybe pareiškiame,
kad produktas WIO, kuriam skirta ši deklaracija,
atitinka žemiau nurodytas Tarybos Direktyvas dėl
ES šalių narių įstatymų suderinimo.
12
Declaration of conformity

LV: ES atbilstības deklarācija
Sabiedrība Grundfos ar pilnu atbildību paziņo, ka
produkts WIO, uz kuru attiecas tālāk redzamā
deklarācija, atbilst tālāk norādītajām Padomes
direktīvām par ES dalībvalstu normatīvo aktu
tuvināšanu.
NL: EU-conformiteitsverklaring
Wij, Grundfos, verklaren geheel onder eigen
verantwoordelijkheid dat product WIO, waarop de
onderstaande verklaring betrekking heeft, in
overeenstemming is met de onderstaande
Richtlijnen van de Raad inzake de onderlinge
aanpassing van de wetgeving van de EU-lidstaten.
PL: Deklaracja zgodności UE
My, Grundfos, oświadczamy z pełną
odpowiedzialnością, że nasz produkt WIO, którego
deklaracja niniejsza dotyczy, jest zgodny z
następującymi dyrektywami Rady w sprawie
zbliżenia przepisów prawnych państw
członkowskich.
PT: Declaração de conformidade UE
A Grundfos declara sob sua única responsabilidade
que o produto WIO, ao qual diz respeito a
declaração abaixo, está em conformidade com as
Directivas do Conselho sobre a aproximação das
legislações dos Estados Membros da UE.
RO: Declaraţia de conformitate UE
Noi Grundfos declarăm pe propria răspundere că
produsul WIO, la care se referă această declaraţie,
este în conformitate cu Directivele de Consiliu
specificate mai jos privind armonizarea legilor
statelor membre UE.
RS: Deklaracija o usklađenosti EU
Mi, kompanija Grundfos, izjavljujemo pod punom
vlastitom odgovornošću da je proizvod WIO, na koji
se odnosi deklaracija ispod, u skladu sa dole
prikazanim direktivama Saveta za usklađivanje
zakona država članica EU.
RU: Декларация о соответствии нормам ЕС
Мы, компания Grundfos, со всей
ответственностью заявляем, что изделие WIO, к
которому относится нижеприведённая
декларация, соответствует нижеприведённым
Директивам Совета Евросоюза о
тождественности законов стран-членов ЕС.
SE: EU-försäkran om överensstämmelse
Vi, Grundfos, försäkrar under ansvar att produkten
WIO, som omfattas av nedanstående försäkran, är i
överensstämmelse med de rådsdirektiv om inbördes
närmande till EU-medlemsstaternas lagstiftning som
listas nedan.
SI: Izjava o skladnosti EU
V Grundfosu s polno odgovornostjo izjavljamo, da je
izdelek WIO,na katerega se spodnja izjava nanaša,
v skladu s spodnjimi direktivami Sveta o
približevanju zakonodaje za izenačevanje pravnih
predpisov držav članic EU.
SK: ES vyhlásenie o zhode
My, spoločnosť Grundfos, vyhlasujeme na svoju
plnú zodpovednosť, že produkt WIO, na ktorý sa
vyhlásenie uvedené nižšie vzťahuje, je v súlade s
ustanoveniami nižšie uvedených smerníc Rady pre
zblíženie právnych predpisov členských štátov EÚ.
TR: AB uygunluk
Grundfos olarak, konusu olan
WIO AB üye
yakınlaştırılmasıyla durumun Konsey
uyumlu olduğunu ve bununla
olarak tüm sorumluluğun olduğunu beyan
UA: Декларація відповідності директивам EU
Ми, компанія Grundfos, під нашу одноосібну
відповідальність заявляємо, що виріб WIO, до
якого відноситься нижченаведена декларація,
відповідає директивам EU, переліченим нижче,
щодо тотожності законів країн-членів ЄС.
CN: 欧盟符合性声明
我们,格兰富,在我们的全权责任下声明,产品 WIO
系列,其制造和性能完全符合以下所列欧盟委员会指
令。
NO: EUs samsvarsærklæring
Vi, Grundfos, erklærer under vårt eneansvar at
produktet WIO, som denne erklæringen gjelder, er i
samsvar med Det europeiske råds direktiver om
tilnærming av forordninger i EU-landene.
AR : ) EU(
WIO
) EU.(
IS: ESB-samræmisyfirlýsing
Við, Grundfos, lýsum því yfir og ábyrgjumst að fullu
að varan WIO, sem þessi yfirlýsing á við um,
samræmist tilskipunum ráðs Evrópubandalaganna
um samræmingu laga aðildarríkja ESB.
13
Declaration of conformity

• EMC Directive (2014/30/EU)
Standard used: EN 61326-1:2013.
• ATEX Directive (2014/34/EU)
Standards used: EN IEC 60079-0:2018, EN 60079-18:2015+A1:2017, EN 60079-7:2015+A1:2018, EN
60079-31:2014.
• RoHS Directives (2011/65/EU and 2015/863/EU)
Standard used: EN 63000:2018.
Certificate No: KEMA 05ATEX2176X
Notified body for EU-type
Certificate:
Dekra Certification B.V. No 0344 Meander 1051, 6825 MJ Arnhem, The
Netherlands.
Notified body for production: Dekra Certification B.V. No 0344 Meander 1051, 6825 MJ Arnhem, The
Netherlands.
Manufacturer: Grundfos Holding A/S, Poul Due Jensens Vej 7, DK-8850 Bjerringbro,
Denmark.
This EU declaration of conformity is only valid when published as part of the Grundfos installation and operating
instructions (publication number 96591899).
Székesfehérvár, 13th of March 2023
Zoltán Lajtos
MUNI Solutions Value Stream Director
Grundfos Holding A/S
Poul Due Jensens Vej 7
8850 Bjerringbro, Denmark
Person authorised to compile technical file and
empowered to sign the EU declaration of conformity.
14
Declaration of conformity

Declaration of conformity
UK declaration of conformity
We, Grundfos, declare under our sole responsibility that the products to which the declaration below relates, are
in conformity with UK regulations, standards and specifications to which conformity is declared, as listed below:
Valid for products:
WIO sensor
• Electromagnetic Compatibility Regulations 2016
Standard used: EN 61326-1:2013.
• Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres Regulations 2016
applies only to products intended for use in potentially explosive environments
Standards used: EN IEC 60079-0:2018, EN 60079-18:2015+A1:2017, EN 60079-7:2015+A1:2018, EN
60079-31:2014.
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2019
Standard used: EN IEC 63000:2018.
Certificate No: BAS21UKEX0282X
Approved body for UK-type Certificate: SGS Baseefa, No 1180, Buxton, UK.
Approved body for production: SGS Baseefa, No 1180, Buxton, UK.
Manufacturer: Grundfos Holding A/S, Poul Due Jensens Vej 7, DK-8850 Bjerringbro,
Denmark.
This UK declaration of conformity is only valid when published as part of the Grundfos installation and operating
instructions (publication number 96591899).
Székesfehérvár, 13th of March 2023
Zoltán Lajtos
MUNI Solutions Value Stream Director
Grundfos Holding A/S
Poul Due Jensens Vej 7
8850 Bjerringbro, Denmark
Manufacturer and person empowered to sign the UK
declaration of conformity.
10000376631
15
Declaration of conformity

Argentina
Bombas GRUNDFOS de Argentina S.A.
Ruta Panamericana km. 37.500industin
1619 - Garín Pcia. de B.A.
Tel.: +54-3327 414 444
Fax: +54-3327 45 3190
Australia
GRUNDFOS Pumps Pty. Ltd.
P.O. Box 2040
Regency Park
South Australia 5942
Tel.: +61-8-8461-4611
Fax: +61-8-8340-0155
Austria
GRUNDFOS Pumpen Vertrieb
Ges.m.b.H.
Grundfosstraße 2
A-5082 Grödig/Salzburg
Tel.: +43-6246-883-0
Fax: +43-6246-883-30
Belgium
N.V. GRUNDFOS Bellux S.A.
Boomsesteenweg 81-83
B-2630 Aartselaar
Tel.: +32-3-870 7300
Fax: +32-3-870 7301
Bosnia and Herzegovina
GRUNDFOS Sarajevo
Zmaja od Bosne 7-7A
BiH-71000 Sarajevo
Tel.: +387 33 592 480
Fax: +387 33 590 465
www.ba.grundfos.com
E-mail: [email protected]
Brazil
BOMBAS GRUNDFOS DO BRASIL
Av. Humberto de Alencar Castelo
Branco, 630
CEP 09850 - 300
São Bernardo do Campo - SP
Tel.: +55-11 4393 5533
Fax: +55-11 4343 5015
Bulgaria
Grundfos Bulgaria EOOD
Slatina District
Iztochna Tangenta street no. 100
BG - 1592 Sofia
Tel.: +359 2 49 22 200
Fax: +359 2 49 22 201
E-mail: [email protected]
Canada
GRUNDFOS Canada inc.
2941 Brighton Road
Oakville, Ontario
L6H 6C9
Tel.: +1-905 829 9533
Fax: +1-905 829 9512
China
GRUNDFOS Pumps (Shanghai) Co. Ltd.
10F The Hub, No. 33 Suhong Road
Minhang District
Shanghai 201106 PRC
Tel.: +86 21 612 252 22
Fax: +86 21 612 253 33
Columbia
GRUNDFOS Colombia S.A.S.
Km 1.5 vía Siberia-Cota Conj. Potrero
Chico,
Parque Empresarial Arcos de Cota Bod.
1A.
Cota, Cundinamarca
Tel.: +57(1)-2913444
Fax: +57(1)-8764586
Croatia
GRUNDFOS CROATIA d.o.o.
Buzinski prilaz 38, Buzin
HR-10010 Zagreb
Tel.: +385 1 6595 400
Fax: +385 1 6595 499
www.hr.grundfos.com
Czech Republic
GRUNDFOS Sales Czechia and Slovakia
s.r.o.
Čajkovského 21
779 00 Olomouc
Tel.: +420-585-716 111
Denmark
GRUNDFOS DK A/S
Martin Bachs Vej 3
DK-8850 Bjerringbro
Tel.: +45-87 50 50 50
Fax: +45-87 50 51 51
E-mail: [email protected]
www.grundfos.com/DK
Estonia
GRUNDFOS Pumps Eesti OÜ
Peterburi tee 92G
11415 Tallinn
Tel.: + 372 606 1690
Fax: + 372 606 1691
Finland
OY GRUNDFOS Pumput AB
Trukkikuja 1
FI-01360 Vantaa
Tel.: +358-(0) 207 889 500
France
Pompes GRUNDFOS Distribution S.A.
Parc d’Activités de Chesnes
57, rue de Malacombe
F-38290 St. Quentin Fallavier (Lyon)
Tel.: +33-4 74 82 15 15
Fax: +33-4 74 94 10 51
Germany
GRUNDFOS GMBH
Schlüterstr. 33
40699 Erkrath
Tel.: +49-(0) 211 929 69-0
Fax: +49-(0) 211 929 69-3799
E-mail: [email protected]
Service in Deutschland:
Greece
GRUNDFOS Hellas A.E.B.E.
20th km. Athinon-Markopoulou Av.
P.O. Box 71
GR-19002 Peania
Tel.: +0030-210-66 83 400
Fax: +0030-210-66 46 273
Hong Kong
GRUNDFOS Pumps (Hong Kong) Ltd.
Unit 1, Ground floor, Siu Wai industrial
Centre
29-33 Wing Hong Street & 68 King Lam
Street, Cheung Sha Wan
Kowloon
Tel.: +852-27861706 / 27861741
Fax: +852-27858664
Hungary
GRUNDFOS Hungária Kft.
Tópark u. 8
H-2045 Törökbálint
Tel.: +36-23 511 110
Fax: +36-23 511 111
India
GRUNDFOS Pumps india Private Limited
118 Old Mahabalipuram Road
Thoraipakkam
Chennai 600 097
Tel.: +91-44 2496 6800
Indonesia
PT GRUNDFOS Pompa
Graha intirub Lt. 2 & 3
Jln. Cililitan Besar No.454. Makasar,
Jakarta Timur
ID-Jakarta 13650
Tel.: +62 21-469-51900
Fax: +62 21-460 6910 / 460 6901
Ireland
GRUNDFOS (Ireland) Ltd.
Unit A, Merrywell Business Park
Ballymount Road Lower
Dublin 12
Tel.: +353-1-4089 800
Fax: +353-1-4089 830
Italy
GRUNDFOS Pompe Italia S.r.l.
Via Gran Sasso 4
I-20060 Truccazzano (Milano)
Tel.: +39-02-95838112
Fax: +39-02-95309290 / 95838461
Japan
GRUNDFOS Pumps K.K.
1-2-3, Shin-Miyakoda, Kita-ku
Hamamatsu
431-2103 Japan
Tel.: +81 53 428 4760
Fax: +81 53 428 5005
Korea
GRUNDFOS Pumps Korea Ltd.
6th Floor, Aju Building 679-5
Yeoksam-dong, Kangnam-ku, 135-916
Seoul, Korea
Tel.: +82-2-5317 600
Fax: +82-2-5633 725
Latvia
SIA GRUNDFOS Pumps Latvia
Deglava biznesa centrs
Augusta Deglava ielā 60
LV-1035, Rīga,
Tel.: + 371 714 9640, 7 149 641
Fax: + 371 914 9646
Lithuania
GRUNDFOS Pumps UAB
Smolensko g. 6
LT-03201 Vilnius
Tel.: + 370 52 395 430
Fax: + 370 52 395 431
Grundfos companies

Malaysia
GRUNDFOS Pumps Sdn. Bhd.
7 Jalan Peguam U1/25
Glenmarie industrial Park
40150 Shah Alam, Selangor
Tel.: +60-3-5569 2922
Fax: +60-3-5569 2866
Mexico
Bombas GRUNDFOS de México
S.A. de C.V.
Boulevard TLC No. 15
Parque industrial Stiva Aeropuerto
Apodaca, N.L. 66600
Tel.: +52-81-8144 4000
Fax: +52-81-8144 4010
Netherlands
GRUNDFOS Netherlands
Veluwezoom 35
1326 AE Almere
Postbus 22015
1302 CA ALMERE
Tel.: +31-88-478 6336
Fax: +31-88-478 6332
E-mail: [email protected]
New Zealand
GRUNDFOS Pumps NZ Ltd.
17 Beatrice Tinsley Crescent
North Harbour Industrial Estate
Albany, Auckland
Tel.: +64-9-415 3240
Fax: +64-9-415 3250
Norway
GRUNDFOS Pumper A/S
Strømsveien 344
Postboks 235, Leirdal
N-1011 Oslo
Tel.: +47-22 90 47 00
Fax: +47-22 32 21 50
Poland
GRUNDFOS Pompy Sp. z o.o.
ul. Klonowa 23
Baranowo k. Poznania
PL-62-081 Przeźmierowo
Tel.: (+48-61) 650 13 00
Fax: (+48-61) 650 13 50
Portugal
Bombas GRUNDFOS Portugal, S.A.
Rua Calvet de Magalhães, 241
Apartado 1079
P-2770-153 Paço de Arcos
Tel.: +351-21-440 76 00
Fax: +351-21-440 76 90
Romania
GRUNDFOS Pompe România SRL
S-PARK BUSINESS CENTER, Clădirea
A2, etaj 2
Str. Tipografilor, Nr. 11-15, Sector 1, Cod
013714
Bucuresti, Romania
Tel.: 004 021 2004 100
E-mail: [email protected]
Serbia
Grundfos Srbija d.o.o.
Omladinskih brigada 90b
11070 Novi Beograd
Tel.: +381 11 2258 740
Fax: +381 11 2281 769
www.rs.grundfos.com
Singapore
GRUNDFOS (Singapore) Pte. Ltd.
25 Jalan Tukang
Singapore 619264
Tel.: +65-6681 9688
Faxax: +65-6681 9689
Slovakia
GRUNDFOS s.r.o.
Prievozská 4D 821 09 BRATISLAVA
Tel.: +421 2 5020 1426
sk.grundfos.com
Slovenia
GRUNDFOS LJUBLJANA, d.o.o.
Leskoškova 9e, 1122 Ljubljana
Tel.: +386 (0) 1 568 06 10
Fax: +386 (0)1 568 06 19
E-mail: [email protected]
South Africa
GRUNDFOS (PTY) LTD
16 Lascelles Drive, Meadowbrook Estate
1609 Germiston, Johannesburg
Tel.: (+27) 10 248 6000
Fax: (+27) 10 248 6002
E-mail: [email protected]
Spain
Bombas GRUNDFOS España S.A.
Camino de la Fuentecilla, s/n
E-28110 Algete (Madrid)
Tel.: +34-91-848 8800
Fax: +34-91-628 0465
Sweden
GRUNDFOS AB
Box 333 (Lunnagårdsgatan 6)
431 24 Mölndal
Tel.: +46 31 332 23 000
Fax: +46 31 331 94 60
Switzerland
GRUNDFOS Pumpen AG
Bruggacherstrasse 10
CH-8117 Fällanden/ZH
Tel.: +41-44-806 8111
Fax: +41-44-806 8115
Taiwan
GRUNDFOS Pumps (Taiwan) Ltd.
7 Floor, 219 Min-Chuan Road
Taichung, Taiwan, R.O.C.
Tel.: +886-4-2305 0868
Fax: +886-4-2305 0878
Thailand
GRUNDFOS (Thailand) Ltd.
92 Chaloem Phrakiat Rama 9 Road
Dokmai, Pravej, Bangkok 10250
Tel.: +66-2-725 8999
Fax: +66-2-725 8998
Turkey
GRUNDFOS POMPA San. ve Tic. Ltd.
Sti.
Gebze Organize Sanayi Bölgesi
Ihsan dede Caddesi
2. yol 200. Sokak No. 204
41490 Gebze/ Kocaeli
Tel.: +90 - 262-679 7979
Fax: +90 - 262-679 7905
E-mail: [email protected]
Ukraine
ТОВ "ГРУНДФОС УКРАЇНА"
Бізнес Центр Європа
Столичне шосе, 103
м. Київ, 03131, Україна
Tel.: (+38 044) 237 04 00
Fax: (+38 044) 237 04 01
E-mail: [email protected]
United Arab Emirates
GRUNDFOS Gulf Distribution
P.O. Box 16768
Jebel Ali Free Zone, Dubai
Tel.: +971 4 8815 166
Fax: +971 4 8815 136
United Kingdom
GRUNDFOS Pumps Ltd.
Grovebury Road
Leighton Buzzard/Beds. LU7 4TL
Tel.: +44-1525-850000
Fax: +44-1525-850011
U.S.A.
Global Headquarters for WU
856 Koomey Road
Brookshire, Texas 77423 USA
Phone: +1-630-236-5500
Uzbekistan
Grundfos Tashkent, Uzbekistan
The Representative Office of Grundfos
Kazakhstan in Uzbekistan
38a, Oybek street, Tashkent
Tel.: (+998) 71 150 3290 / 71 150 3291
Fax: (+998) 71 150 3292
Grundfos companies

96591899 04.2023
ECM: 1313330
www.grundfos.com
Trademarks displayed in this material, including but not limited to Grundfos and the Grundfos logo, are registered trademarks owned by The Grundfos Group. © 2023 Grundfos Holding A/S, all rights reserved.
Other manuals for WIO sensor
1
Table of contents
Other Grundfos Accessories manuals

Grundfos
Grundfos DPI User manual

Grundfos
Grundfos LiqTec User manual

Grundfos
Grundfos Pt100 User manual

Grundfos
Grundfos WIO sensor User manual

Grundfos
Grundfos LiqTec User manual

Grundfos
Grundfos Terminator User manual

Grundfos
Grundfos DPI User manual

Grundfos
Grundfos MAGNA3 25-100 (N) User manual

Grundfos
Grundfos LiqTec User manual

Grundfos
Grundfos Pt100 User manual