Grundfos SI 010 CNV User manual

SI 010 CNV
GRUNDFOS INSTRUCTIONS
Installation and operating instructions

2
Declaration of Conformity
We, Grundfos, declare under our sole responsibility that the product SI 010 CNV, to which this
declaration relates, is in conformity with these Council directives on the approximation of the laws of the
EC member states:
– Low Voltage Directive (2006/95/EC).
Standard used: EN 61010-1: 2001.
– EMC Directive (2004/108/EC).
Standard used: EN 61326-1: 2006.
Konformitätserklärung
Wir, Grundfos, erklären in alleiniger Verantwortung, dass das Produkt SI 010 CNV, auf das sich diese
Erklärung bezieht, mit den folgenden Richtlinien des Rates zur Angleichung der Rechtsvorschriften der
EU-Mitgliedsstaaten übereinstimmt:
– Niederspannungsrichtlinie (2006/95/EG).
Norm, die verwendet wurde: EN 61010-1: 2001.
– EMV-Richtlinie (2004/108/EG).
Norm, die verwendet wurde: EN 61326-1: 2006.
Déclaration de Conformité
Nous, Grundfos, déclarons sous notre seule responsabilité, que le produit SI 010 CNV, auquel se réfère
cette déclaration, est conforme aux Directives du Conseil concernant le rapprochement des législations
des Etats membres CE relatives aux normes énoncées ci-dessous :
– Directive Basse Tension (2006/95/CE).
Norme utilisée : EN 61010-1: 2001.
– Directive Compatibilité Electromagnétique CEM (2004/108/CE).
Norme utilisée : EN 61326-1: 2006.
Dichiarazione di Conformità
Grundfos dichiara sotto la sua esclusiva responsabilità che il prodotto SI 010 CNV, al quale si riferisce
questa dichiarazione, è conforme alle seguenti direttive del Consiglio riguardanti il riavvicinamento delle
legislazioni degli Stati membri CE:
– Direttiva Bassa Tensione (2006/95/CE).
Norma applicata: EN 61010-1: 2001.
– Direttiva EMC (2004/108/CE).
Norma applicata: EN 61326-1: 2006.
Declaración de Conformidad
Nosotros, Grundfos, declaramos bajo nuestra propia responsabilidad que el producto SI 010 CNV, al
cual se refiere esta declaración, está conforme con las Directivas del Consejo en la aproximación de las
leyes de los Estados Miembros del EM:
– Directiva de Baja Tensión (2006/95/CE).
Norma aplicada: EN 61010-1: 2001.
– Directiva EMC (2004/108/CE).
Norma aplicada: EN 61326-1: 2006.

3
Δήλωση Συμμόρφωσης
Εμείς, ηGrundfos, δηλώνουμε με αποκλειστικά δική μας ευθύνη ότι τα προϊόντα SI 010 CNV, στα οποία
αναφέρεται ηπαρούσα δήλωση, συμμορφώνονται με τις εξής Οδηγίες του Συμβουλίου περί προσέγγισης
των νομοθεσιών των κρατών μελών της ΕΕ:
–Οδηγία χαμηλής τάσης (2006/95/EC).
Πρότυπο που χρησιμοποιήθηκε: EN 61010-1: 2001.
–Οδηγία Ηλεκτρομαγνητικής Συμβατότητας (EMC) (2004/108/EC).
Πρότυπο που χρησιμοποιήθηκε: EN 61326-1: 2006.
Overensstemmelseserklæring
Vi, Grundfos, erklærer under ansvar at produktet SI 010 CNV som denne erklæring omhandler, er i
overensstemmelse med disse af Rådets direktiver om indbyrdes tilnærmelse til EF-medlemsstaternes
lovgivning:
– Lavspændingsdirektivet (2006/95/EF).
Anvendt standard: EN 61010-1: 2001.
– EMC-direktivet (2004/108/EF).
Anvendt standard: EN 61326-1: 2006.
Deklaracja zgodności
My, Grundfos, oświadczamy z pełnąodpowiedzialnością, że nasze wyroby SI 010 CNV, których
deklaracja niniejsza dotyczy, sązgodne z następującymi wytycznymi Rady d/s ujednolicenia przepisów
prawnych krajów członkowskich WE:
– Dyrektywa Niskonapięciowa (LVD) (2006/95/WE).
Zastosowana norma: EN 61010-1: 2001.
– Dyrektywa EMC (2004/108/WE).
Zastosowana norma: EN 61326-1: 2006.
Декларация осоответствии
Мы, компания Grundfos, со всей ответственностью заявляем, что изделия SI 010 CNV, ккоторым
относится настоящая декларация, соответствуют следующим Директивам Совета Евросоюза об
унификации законодательных предписаний стран-членов ЕС:
–Низковольтное оборудование (2006/95/EC).
Применявшийся стандарт: EN 61010-1: 2001.
–Электромагнитная совместимость (2004/108/EC).
Применявшийся стандарт: EN 61326-1: 2006.
Megfelelőségi nyilatkozat
Mi, a Grundfos, egyedüli felelősséggel kijelentjük, hogy a SI 010 CNV termék, amelyre jelen nyilatkozik
vonatkozik, megfelel az Európai Unió tagállamainak jogi irányelveit összehangoló tanács alábbi
előírásainak:
– KisfeszültségűDirektíva (2006/95/EK).
Alkalmazott szabvány: EN 61010-1: 2001.
– EMC Direktíva (2004/108/EK).
Alkalmazott szabvány: EN 61326-1: 2006.

4
Prohlášení o shodě
My firma Grundfos prohlašujeme na svou plnou odpovědnost, že výrobek SI 010 CNV, na nějž se toto
prohlášení vztahuje, je v souladu s ustanoveními směrnice Rady pro sblížení právních předpisů
členských státůEvropského společenství v oblastech:
–Směrnice pro nízkonapět’ové aplikace (2006/95/ES).
Použitá norma: EN 61010-1: 2001.
–Směrnice pro elektromagnetickou kompatibilitu (EMC) (2004/108/ES).
Použitá norma: EN 61326-1: 2006.
Bjerringbro, 15th June 2009
Henning Sandager
Technical Director

5
SI 010 CNV
Installation and operating instructions 6
Montage- und Betriebsanleitung 19
Notice d'installation et de fonctionnement 31
Istruzioni di installazione e funzionamento 43
Instrucciones de instalación y funcionamiento 56
Οδηγίες εγκατάστασης και λειτουργίας 69
Monterings- og driftsinstruktion 81
Instrukcja montażu i eksploatacji 93
Руководство по монтажу иэксплуатации 105
Szerelési és üzemeltetési utasítás 119
Montážní a provozní návod 131

6
Original installation and operating instructions.
CONTENTS Page
1. Symbols used in this document 6
2. General description 7
2.1 Application 7
2.2 Nameplate 7
2.3 Installation kit 7
3. Configuration 8
3.1 ST5 - supply voltage 9
3.2 ST3 and ST4 - sensor inputs 9
3.3 ST1 and ST2 - signal outputs 10
3.4 Configuration examples 11
4. Installation 13
4.1 Mounting 13
4.2 Electrical connection 14
4.2.1 Connection of supply voltage and sensor 15
5. Technical data 17
6. Disposal 18
1. Symbols used in this document
Warning
Prior to installation, read these installation and operating
instructions. Installation and operation must comply with
local regulations and accepted codes of good practice.
Warning
If these safety instructions are not observed, it may result in
personal injury!
Caution
If these safety instructions are not observed, it may result in
malfunction or damage to the equipment!
Note
Notes or instructions that make the job easier and ensure safe
operation.

7
2. General description
Grundfos SI 010 CNV, sensor interface, is an external power supply, signal
amplifier and signal converter for Grundfos sensors. SI 010 CNV has built-in
precision resistors enabling the transmitter to give 1-5 V and 2-10 V output
signals in stead of 4-20 mA.
2.1 Application
SI 010 CNV is used in sensor applications with controllers with 4-20 mA
inputs in which the pressure and flow measurements are carried out by
products from the Grundfos Direct Sensors™ standard product range.
2.2 Nameplate
Fig. 1 Example of nameplate
2.3 Installation kit
The SI 010 CNV package contains these parts:
• SI 010 CNV unit
• installation and operating instructions for SI 010 CNV.
TM04 4898 2209
Pos. Description
1 Type designation
2 Product number
3 Version number
4 Production code (year and week)
5 Serial number
6IPclass
7 Supply voltage
8 Maximum input power
9CEmarking
Type
Product No.
Un
Pmax
Serial No.
P.c.
IP
V-No.
Made in Thailand
SENSOR INTERFACE
!
13
4
5
6
7
8
9
2

8
3. Configuration
Set the converter (SI 010 CNV) to the desired function before installing it.
Carefully tip off the cover of the plastic cabinet using a small, flat
screwdriver. See fig. 2.
Fig. 2 Press in the tabs on both sides using a screwdriver
Inside the converter six small jumpers can be placed differently depending
on the desired function. The short-circuit positions are designated ST1, ST2,
ST3, ST4, ST5. See fig. 3.
Fig. 3 Short-circuit positions on PC board
Figure 3 shows a picture of SI 010 CNV without cover. The circles, ST1-ST5,
show the physical position of the short-circuit positions.
TM04 4883 2209TM04 4884 2209
Warning
The SI 010 CNV must be configured before cables are
connected as it is highly dangerous to configure the unit
when power is connected.
ST1 ST2
ST3 ST4
ST5

9
3.1 ST5 - supply voltage
In position ST5, SI 010 CNV can be set to either 230 V or 115 V supply
voltage:
• one jumper across the two pins in the middle = 230 V
• two jumpers as shown in fig. 4 = 115 V.
If the converter is connected to 24 VDC, the configuration of ST5 has no
function.
Fig. 4 How to set SI 010 CNV to 230 V and 115 V
3.2 ST3 and ST4 - sensor inputs
The sensors are available in two versions with different output signals, either
0.5 - 3.5 V or 0.5 - 4.5 V. The converter is compatible with both signal types
which are configured in short-circuit positions ST3 and ST4.
Caution
The SI 010 CNV can be connected to either 230/115 VAC or
24 VDC. It must NOT be connected to both voltages.
TM04 4885 2209, TM04 4886 2209
Short-circuit
position Location (see fig. 7) Function
ST3 LInput 1, input voltage 0.5 - 3.5 V
(factory setting)
H Input 1, input voltage 0.5 - 4.5 V
ST4 LInput 2, input voltage 0.5 - 3.5 V
(factory setting)
H Input 2, input voltage 0.5 - 4.5 V
Set to 230 V (factory setting)
Set to 115 V

10
Fig. 5 ST3 (input 1) is configured for sensors giving an 0.5 - 3.5 V signal,
ST4 (input 2) is configured for sensors giving an 0.5 - 4.5 V signal
3.3 ST1 and ST2 - signal outputs
Fig. 6 ST1 (output 1) is set to 2-10 V, and ST2 (output 2) to 1-5 V
TM04 4888 2206
Short-circuit
position Location (see fig. 7) Function
ST1
I Output 1, output current 4-20 mA (factory setting)
U1 Output 1, output voltage 2-10 V
U2 Output 1, output voltage 1-5 V
ST2
I Output 2, output current 4-20 mA (factory setting)
U1 Output 2, output voltage 2-10 V
U2 Output 2, output voltage 1-5 V
TM04 4887 2209