Grundfos JP Basic Booster User manual

GRUNDFOS INSTRUCTIONS
JP Basic Booster
Installation and operating instructions

2

Table of contents
3
JP Basic Booster
Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
English (GB)
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Български (BG)
Упътване за монтаж иексплоатация. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Čeština (CZ)
Montážní a provozní návod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hrvatski (HR)
Montažne i pogonske upute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Magyar (HU)
Szerelési és üzemeltetési utasítás . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Українська (UA)
Інструкції змонтажу та експлуатації . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Polski (PL)
Instrukcja montażu i eksploatacji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Русский (RU)
Руководство по монтажу иэксплуатации . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Română(RO)
Instrucţiuni de instalare şi utilizare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Slovenčina (SK)
Návod na montáž a prevádzku . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Slovensko (SI)
Navodila za montažo in obratovanje. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Srpski (RS)
Uputstvo za instalaciju i rad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Türkçe (TR)
Montaj ve kullanım kılavuzu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Declaration of conformity
4
Declaration of conformity
GB: EC declaration of conformity
We, Grundfos, declare under our sole responsibility that the product
JP Basic Booster, to which this declaration relates, is in conformity with
these Council directives on the approximation of the laws of
the EC member states:
– Machinery Directive (2006/42/EC).
Standard used: EN 809: 2009.
– Low Voltage Directive (2006/95/EC).
Standards used: EN 60335-1: 2002 and EN 60335-2-41: 2003.
– EMC Directive (2004/108/EC).
Standards used: EN 60730-1: 2000 and EN 60730-1, A16: 2007.
– Ecodesign Directive (2009/125/EC).
Electric motors:
Commission Regulation No. 640/2009.
Applies only to three-phase Grundfos motors marked IE2 or IE3.
See motor nameplate.
Standard used: EN 60034-30: 2009.
BG: EC декларация за съответствие
Ние, фирма Grundfos, заявяваме спълна отговорност, че продукта
JP Basic Booster, за който се отнася настоящата декларация,
отговаря на следните указания на Съвета за уеднаквяване на
правните разпоредби на държавите членки на ЕС:
–Директива за машините (2006/42/EC).
Приложен стандарт: EN 809: 2009.
–Директива за нисковолтови системи (2006/95/EC).
Приложени стандарти: EN 60335-1: 2002 иEN 60335-2-41: 2003.
–Директива за електромагнитна съвместимост (2004/108/EC).
Приложени стандарти: EN 60730-1: 2000 иEN 60730-1,
A16: 2007.
–Директива за екодизайн (2009/125/EC).
Електродвигатели:
Регламент на Комисията №640/2009.
Отнася се само за трифазни електродвигатели на Grundfos,
маркирани сIE2 или IE3. Вижте табелата сданни на двигателя.
Приложен стандарт: EN 60034-30: 2009.
CZ: ES prohlášení o shodě
My firma Grundfos prohlašujeme na svou plnou odpovědnost,
že výrobek JP Basic Booster, na nějž se toto prohlášení vztahuje, je v
souladu s ustanoveními směrnice Rady pro sblížení právních předpisů
členských státůEvropského společenství v oblastech:
–Směrnice pro strojní zařízení (2006/42/ES).
Použitá norma: EN 809: 2009.
–Směrnice pro nízkonapět’ové aplikace (2006/95/ES).
Použité normy: EN 60335-1: 2002 a EN 60335-2-41: 2003.
–Směrnice pro elektromagnetickou kompatibilitu (EMC)
(2004/108/ES).
Použité normy: EN 60730-1: 2000 a EN 60730-1, A16: 2007.
–Směrnice o požadavcích na ekodesign (2009/125/ES).
Elektrické motory:
Nařízení Komise č. 640/2009.
Platí pouze pro třífázové motory Grundfos označené IE2 nebo IE3.
Viz typový štítek motoru.
Použitá norma: EN 60034-30: 2009.
HR: EZ izjava o usklađenosti
Mi, Grundfos, izjavljujemo pod vlastitom odgovornošću da je proizvod
JP Basic Booster, na koji se ova izjava odnosi, u skladu s direktivama
ovog Vijeća o usklađivanju zakona država članica EU:
– Direktiva za strojeve (2006/42/EZ).
Korištena norma: EN 809: 2009.
– Direktiva za niski napon (2006/95/EZ).
Korištene norme: EN 60335-1: 2002 i EN 60335-2-41: 2003.
– Direktiva za elektromagnetsku kompatibilnost (2004/108/EZ).
Korištene norme: EN 60730-1: 2000 i EN 60730-1, A16: 2007.
– Direktiva o ekološkoj izvedbi (2009/125/EZ).
Električni motori:
Regulativa komisije br. 640/2009.
Odnosi se samo na trofazne Grundfos motore s oznakama IE2 ili
IE3. Pogledajte natpisnu pločicu motora.
Korištena norma: EN 60034-30: 2009.
HU: EK megfelelőségi nyilatkozat
Mi, a Grundfos, egyedüli felelősséggel kijelentjük, hogy a
JP Basic Booster termék, amelyre jelen nyilatkozik vonatkozik, megfelel
az Európai Unió tagállamainak jogi irányelveit összehangoló tanács
alábbi előírásainak:
– Gépek (2006/42/EK).
Alkalmazott szabvány: EN 809: 2009.
– KisfeszültségűDirektíva (2006/95/EK).
Alkalmazott szabványok: EN 60335-1: 2002 és
EN 60335-2-41: 2003.
– EMC Direktíva (2004/108/EK).
Alkalmazott szabványok: EN 60730-1: 2000 és EN 60730-1,
A16: 2007.
– Környezetbarát tervezésre vonatkozó irányelv (2009/125/EK).
Villamos motorok:
A Bizottság 640/2009/EK rendelete.
Csak az IE2 vagy IE3 jelzésűháromfázisú Grundfos motorokra
vonatkozik. Lásd a motor adattábláját.
Alkalmazott szabvány: EN 60034-30: 2009.
UA: Свідчення про відповідність вимогам ЄС
Компанія Grundfos заявляє про свою виключну відповідальність
за те, що продукт JP Basic Booster, на який поширюється дана
декларація, відповідає таким рекомендаціям Ради зуніфікації
правових норм країн - членів ЄС:
–Механічні прилади (2006/42/ЄС).
Стандарти, що застосовувалися: EN 809: 2009.
–Низька напруга (2006/95/ЄС).
Стандарти, що застосовувалися: EN 60335-1: 2002 та
EN 60335-2-41: 2003.
–Електромагнітна сумісність (2004/108/ЄС).
Стандарти, що застосовувалися: EN 60730-1: 2000 та
EN 60730-1, A16: 2007.
–Директива зекодизайну (2009/125/ЄС).
Електродвигуни:
Постанова Комісії №640/2009.
Застосовується тільки до трифазних електродвигунів Grundfos,
позначених IE2 або IE3. Дивіться паспортну табличку
електродвигуна.
Стандарти, що застосовувалися: EN 60034-30: 2009.
PL: Deklaracja zgodności WE
My, Grundfos, oświadczamy z pełnąodpowiedzialnością, że nasze
wyroby JP Basic Booster, których deklaracja niniejsza dotyczy, są
zgodne z następującymi wytycznymi Rady d/s ujednolicenia przepisów
prawnych krajów członkowskich WE:
– Dyrektywa Maszynowa (2006/42/WE).
Zastosowana norma: EN 809: 2009.
– Dyrektywa Niskonapięciowa (LVD) (2006/95/WE).
Zastosowane normy: EN 60335-1: 2002 oraz EN 60335-2-41: 2003.
– Dyrektywa EMC (2004/108/WE).
Zastosowane normy: EN 60730-1: 2000 oraz EN 60730-1,
A16: 2007.
– Dyrektywa Ekoprojektowa (2009/125/WE).
Silniki elektryczne:
Rozporządzenie Komisji (WE) Nr 640/2009.
Dotyczy tylko trójfazowych silników firmy Grundfos z oznaczeniami
IE2 lub IE3. Patrz tabliczka znamionowa silnika.
Zastosowana norma: EN 60034-30: 2009.
RU: Декларация осоответствии ЕС
Мы, компания Grundfos, со всей ответственностью заявляем,
что изделия JP Basic Booster, ккоторым относится настоящая
декларация, соответствуют следующим Директивам Совета
Евросоюза об унификации законодательных предписаний
стран-членов ЕС:
–Механические устройства (2006/42/ЕС).
Применявшийся стандарт: EN 809: 2009.
–Низковольтное оборудование (2006/95/EC).
Применявшиеся стандарты: EN 60335-1: 2002 и
EN 60335-2-41: 2003.
–Электромагнитная совместимость (2004/108/EC).
Применявшиеся стандарты: EN 60730-1: 2000 иEN 60730-1,
A16: 2007.
–Директива по экологическому проектированию
энергопотребляющей продукции (2009/125/EC).
Электродвигатели:
Постановление Комиссии №640/2009.
Применяется только ктрехфазным электродвигателям Grundfos,
обозначенным IE2 или IE3. См. шильдик стехническими
данными двигателя.
Применявшийся стандарт: EN 60034-30: 2009.

Declaration of conformity
5
RO: Declaraţie de conformitate CE
Noi, Grundfos, declarãm pe propria rãspundere cã produsele
JP Basic Booster, la care se referã aceastã declaraþie, sunt în
conformitate cu aceste Directive de Consiliu asupra armonizãrii legilor
Statelor Membre CE:
– Directiva Utilaje (2006/42/CE).
Standard utilizat: EN 809: 2009.
– Directiva Tensiune Joasă(2006/95/CE).
Standarde utilizate: EN 60335-1: 2002 şi EN 60335-2-41: 2003.
– Directiva EMC (2004/108/CE).
Standarde utilizate: EN 60730-1: 2000 şi EN 60730-1, A16: 2007.
– Directiva Ecodesign (2009/125/CE).
Motoare electrice:
Regulamentul Comisiei nr. 640/2009.
Se aplicănumai motoarelor trifazate Grundfos cu marca IE2 sau IE3.
Vezi plăcuţa de identificare a motorului.
Standard utilizat: EN 60034-30: 2009.
SK: Prehlásenie o konformite EÚ
My firma Grundfos prehlasujeme na svoju plnú zodpovednost’,
že výrobok JP Basic Booster, na ktorý sa toto prehlásenie vzt’ahuje, je v
súlade s ustanovením smernice Rady pre zblíženie právnych predpisov
členských štátov Európskeho spoločenstva v oblastiach:
– Smernica pre strojové zariadenie (2006/42/EC).
Použitá norma: EN 809: 2009.
– Smernica pre nízkonapät’ové aplikácie (2006/95/EC).
Použité normy: EN 60335-1: 2002 a EN 60335-2-41: 2003.
– Smernica pre elektromagnetickú kompatibilitu (2004/108/EC).
Použité normy: EN 60730-1: 2000 a EN 60730-1, A16: 2007.
– Smernica o ekodizajne (2009/125/EC).
Elektromotory:
Nariadenie Komisie č. 640/2009.
Platné iba pre trojfázové motory Grundfos, označené ako IE2 alebo
IE3. Viďtypový štítok motora.
Použitá norma: EN 60034-30: 2009.
SI: ES izjava o skladnosti
V Grundfosu s polno odgovornostjo izjavljamo, da so naši izdelki
JP Basic Booster, na katere se ta izjava nanaša, v skladu z naslednjimi
direktivami Sveta o približevanju zakonodaje za izenačevanje pravnih
predpisov držav članic ES:
– Direktiva o strojih (2006/42/ES).
Uporabljena norma: EN 809: 2009.
– Direktiva o nizki napetosti (2006/95/ES).
Uporabljeni normi: EN 60335-1: 2002 in EN 60335-2-41: 2003.
– Direktiva o elektromagnetni združljivosti (EMC) (2004/108/ES).
Uporabljeni normi: EN 60730-1: 2000 in EN 60730-1, A16: 2007.
– Eco-design direktiva (2009/125/ES).
Električni motorji:
Uredba Komisije št. 640/2009.
Se nanaša samo na trofazne motorje Grundfos z oznako IE2 ali IE3.
Glejte napisno ploščico motorja.
Uporabljena norma: EN 60034-30: 2009.
RS: EC deklaracija o konformitetu
Mi, Grundfos, izjavljujemo pod vlastitom odgovornošću da je proizvod
JP Basic Booster, na koji se ova izjava odnosi, u skladu sa direktivama
Saveta za usklađivanje zakona država članica EU:
– Direktiva za mašine (2006/42/EC).
Korišćen standard: EN 809: 2009.
– Direktiva niskog napona (2006/95/EC).
Korišćeni standardi: EN 60335-1: 2002 i EN 60335-2-41: 2003.
– EMC direktiva (2004/108/EC).
Korišćeni standardi: EN 60730-1: 2000 i EN 60730-1, A16: 2007.
– Direktiva o ekološkom projektovanju (2009/125/EC).
Električni motori:
Propis Komisije br. 640/2009.
Važi samo za trofazne Grundfos motore označene sa IE2 ili IE3.
Pogledajte natpisnu pločicu motora.
Korišćen standard: EN 60034-30: 2009.
TR: EC uygunluk bildirgesi
Grundfos olarak bu beyannameye konu olan JP Basic Booster
ürünlerinin, AB Üyesi Ülkelerin kanunlarınıbirbirine yaklaştırma üzerine
Konsey Direktifleriyle uyumlu olduğunun yalnızca bizim
sorumluluğumuz altında olduğunu beyan ederiz:
– Makineler Yönetmeliği (2006/42/EC).
Kullanılan standart: EN 809: 2009.
–Düşük Voltaj Yönetmeliği (2006/95/EC).
Kullanılan standartlar: EN 60335-1: 2002 ve EN 60335-2-41: 2003.
– EMC Diretifi (2004/108/EC).
Kullanılan standartlar: EN 60730-1: 2000 ve EN 60730-1, A16: 2007.
– Ecodesign Direktifi (2009/125/EC).
Elektrikli motorlar:
640/2009 sayılıKomisyon Yönetmeliği.
Sadece IE2 veya IE3 işaretli trifaze Grundfos motorlar için geçerlidir.
Motor bilgi etiketine bakınız.
Kullanılan standart: EN 60034-30: 2009.
Bjerringbro, 1st December 2011
Svend Aage Kaae
Technical Director
Grundfos Holding A/S
Poul Due Jensens Vej 7
8850 Bjerringbro, Denmark
Person authorised to compile technical file and
empowered to sign the EC declaration of conformity.

English (GB)
6
English (GB) Safety instructions
CONTENTS Page
1. Symbols used in this document
2. Applications
The JP Basic Booster is suitable for pressure
boosting of fresh water in domestic water supply
systems.
3. System sizing
4. Electrical connection
Check that the supply voltage and frequency
correspond to the values stated on the nameplate.
Single-phase motors incorporate a thermal switch
and require no additional motor protection.
1. Symbols used in this document 6
2. Applications 6
3. System sizing 6
4. Electrical connection 6
5. Start-up 7
5.1 Shaft seal run-in 7
6. Adjustment 7
6.1 Calculating the cut-in and cut-out
pressures 7
6.2 Adjusting the precharge pressure 7
6.3 Setting the pressure switch 8
7. Operation and maintenance 8
8. Frost protection 8
9. Technical data 8
10. Fault finding 9
11. Disposal 9
Warning
Prior to installation, read these
installation and operating instructions.
Installation and operation must comply
with local regulations and accepted
codes of good practice.
Warning
If these safety instructions are not
observed, it may result in personal
injury.
Warning
If these instructions are not observed,
it may lead to electric shock with
consequent risk of serious personal
injury or death.
Caution
If these safety instructions are not
observed, it may result in malfunction
or damage to the equipment.
Note
Notes or instructions that make the job
easier and ensure safe operation.
Warning
The system in which the product is
incorporated must be designed for the
maximum pump pressure.
Warning
The electrical installation should be
carried out by an authorised person in
accordance with local regulations.
Warning
During electrical installation, make sure
that the power supply cannot be
accidentally switched on.
Warning
The unit must be connected to an
external mains switch with a minimum
contact gap of 3 mm in all poles.
As a precaution, the pump must be
connected to a socket with earth
connection.
We recommend to fit the permanent
installation with an earth leakage circuit
breaker (ELCB) with a tripping current
≤ 30 mA.

English (GB)
7
5. Start-up
5.1 Shaft seal run-in
The seal faces are lubricated by the pumped liquid,
meaning that there may be a certain amount of
leakage from the shaft seal.
When the pump is started up for the first time, or
when a new shaft seal is installed, a certain run-in
period is required before the leakage is reduced to
an acceptable level. The time required for this
depends on the operating conditions, i.e. every time
the operating conditions change, a new run-in period
will be started.
Under normal conditions, the leaking liquid will
evaporate. As a result, no leakage will be detected.
6. Adjustment
The JP Basic Booster comes with the following
factory settings in bar:
6.1 Calculating the cut-in and cut-out
pressures
The cut-in pressure is the sum of these variables:
• required minimum pressure at the highest
tapping point
• head from the pump to the highest tapping point
• pressure loss in pipes.
Recommended cut-out pressure:
cut-in pressure + 0.8 - 1.5 bar.
6.2 Adjusting the precharge pressure
When the pump cut-in pressure has been
determined, the required precharge pressure of the
diaphragm tank can be calculated. The precharge
pressure must be adjusted to 90 % of the cut-in
pressure.
See the installation and operating instructions for the
diaphragm tank.
Caution
Do not start the pump until it has been
filled with liquid.
Note
We recommend to fit a non-return valve
on the suction side of the pump. Pump Tank
precharge
pressure
Cut-in
pressure Cut-out pressure
JPBasic
Booster 1.9 2.0 2.8
Note
The cut-out pressure must not exceed
the maximum discharge pressure of the
pump.
Caution
When adjusting/reading the precharge
pressure, make sure that there is no
water pressure on the diaphragm tank
from the pipework.
Note
If the pressure switch setting is
changed, the precharge pressure must
be adjusted too.

English (GB)
8
6.3 Setting the pressure switch
The cut-out pressure must be lower than the
maximum operating pressure of the pump and tank.
Remove the cover from the pressure switch to
access the adjusting screws. See fig. 1.
Fig. 1 Pressure switch
Setting the cut-out pressure
1. Turn screw (pos. A) clockwise to increase the
cut-out pressure.
Turn it counter-clockwise to reduce the cut-out
pressure.
The differential pressure range remains
unchanged.
2. Start the pump and check by reading the
pressure gauge whether the desired cut-out and
cut-in pressures have been obtained.
Setting the cut-in pressure
1. Turn screw (pos. B) clockwise to reduce the
cut-in pressure.
Turn it counter-clockwise to increase the cut-in
pressure.
The differential pressure range is widened and
narrowed respectively.
2. Start the pump and check by reading the
pressure gauge whether the desired cut-out and
cut-in pressures have been obtained.
Repeat the procedure until the right cut-in and
cut-out pressures have been obtained.
7. Operation and maintenance
8. Frost protection
If there is a risk of frost, the tank and pump must be
drained.
9. Technical data
Ambient temperature
Maximum +40 °C.
Storage temperature
Minimum -10 °C.
Maximum +45 °C.
Liquid temperature
+35 °C.
System pressure
Maximum 6 bar.
Inlet pressure
At inlet pressures above 1.5 bar the discharge
pressure must be at least 2.5 bar.
Supply voltage
1 x 220-240 V, 50 Hz.
Insulation class
F.
Enclosure class
IP44.
Relative air humidity
Maximum 95 %.
Sound power level
The sound power level of the pump is lower than
72 dB(A).
Start/stop frequency
Maximum 20 per hour.
Warning
Switch off the power supply before
adjusting the pressure switch.
Fit the cover on the pressure switch
before you switch on the power supply
to check the cut-in and cut-out
pressure.
TM05 2711 0412
Warning
Prior to start-up, the system should be
flushed through with clean water and
drained to remove possible impurities.
Caution
Do not cover the motor of the booster
system as an adequate supply of cool
air must reach the motor cooling fan.

English (GB)
9
10. Fault finding
* Or contact the nearest Grundfos company or
service workshop.
11. Disposal
This product or parts of it must be disposed of in an
environmentally sound way:
1. Use the public or private waste collection service.
2. If this is not possible, contact the nearest
Grundfos company or service workshop.
Subject to alterations.
Warning
Before starting fault finding, switch off
the power supply. Make sure that the
power supply cannot be accidentally
switched on.
Fault Cause Remedy
1. The pump does
not start. a) The fuses in the electric installation have burnt. Replace the fuses. If the new fuses also burn, check the electric installation.
b) The earth leakage circuit
breaker or the
voltage-operated circuit
breaker has tripped.
Cut in the circuit breaker and check the electric
installation.
2. There is power on
the pressure
switch but not the
pump.
a) The power supply to the pump
is disconnected after the
pressure switch unit.
Check the cable connections.
b) The pressure switch unit is
defective. Repair or replace the pressure switch unit. *
3. The pump does
not start when
water is
consumed.
a) Too big difference in height
between the pressure switch
unit and the tapping point.
Adjust the cut-in pressure.
b) The pressure switch unit is
defective. Repair or replace the pressure switch unit. *
4. Frequent
starts/stops. a) Leakage in the pipework. Check and repair the pipework.
b) The pressure tank has no
precharge pressure, or the
tank size is insufficient.
Check the tank precharge pressure, and
recharge the tank, if necessary. See section 6.
5. The pump does
not stop. a) The pressure switch unit is defective. Repair or replace the pressure switch unit. *
6. The motor cuts
out during
operation.
a) The thermal switch in the
motor has tripped due to
overheating.
The thermal switch will cut in automatically
when the motor has cooled sufficiently.
If the problem still persists, check these two
possible causes:
• Impeller stuck.
Clean the pump.
• Motor defective.
Repair or replace the motor. *

Grundfos companies
Argentina
Bombas GRUNDFOS de Argentina S.A.
Ruta Panamericana, ramal Campana
Centro Industrial Garín - Esq. Haendel y
Mozart
AR-1619 Garín Pcia. de Buenos Aires
Pcia. de Buenos Aires
Phone: [phone]
Telefax: [phone]
Australia
GRUNDFOS Pumps Pty. Ltd.
P.O. Box 2040
Regency Park
South Australia 5942
Phone: [phone]
Telefax: [phone]
Austria
GRUNDFOS Pumpen Vertrieb
Ges.m.b.H.
Grundfosstraße 2
A-5082 Grödig/Salzburg
Tel.: [phone]
Telefax: [phone]
Belgium
N.V. GRUNDFOS Bellux S.A.
Boomsesteenweg 81-83
B-2630 Aartselaar
Tél.: [phone]
Télécopie: [phone]
Belorussia
Представительство ГРУНДФОС в
Минске
220123, Минск,
ул. В. Хоружей, 22, оф. 1105
Тел.: +(37517) 233 97 65,
Факс: +(37517) 233 97 69
E-mail: grundfos_m[email protected]
Bosnia/Herzegovina
GRUNDFOS Sarajevo
Trg Heroja 16,
BiH-71000 Sarajevo
Phone: [phone]
Telefax: [phone]
e-mail: grun[email protected].ba
Brazil
BOMBAS GRUNDFOS DO BRASIL
Av. Humberto de Alencar Castelo
Branco, 630
CEP 09850 - 300
São Bernardo do Campo - SP
Phone: [phone]
Telefax: [phone]
Bulgaria
Grundfos Bulgaria EOOD
Slatina District
Iztochna Tangenta street no. 100
BG - 1592 Sofia
Tel. [phone]
Fax. [phone]
email: [e-mail]
Canada
GRUNDFOS Canada Inc.
2941 Brighton Road
Oakville, Ontario
L6H 6C9
Phone: [phone]
Telefax: [phone]
China
GRUNDFOS Pumps (Shanghai) Co. Ltd.
50/F Maxdo Center No. 8 XingYi Rd.
Hongqiao development Zone
Shanghai 200336
PRC
Phone: [phone]
Telefax: [phone]
Croatia
GRUNDFOS CROATIA d.o.o.
Cebini 37, Buzin
HR-10010 Zagreb
Phone: [phone]
Telefax: [phone]
www.grundfos.hr
Czech Republic
GRUNDFOS s.r.o.
Čajkovského 21
779 00 Olomouc
Phone: [phone]
Telefax: [phone]
Denmark
GRUNDFOS DK A/S
Martin Bachs Vej 3
DK-8850 Bjerringbro
Tlf.: [phone]
Telefax: [phone]
E-mail: [email protected]
www.grundfos.com/DK
Estonia
GRUNDFOS Pumps Eesti OÜ
Peterburi tee 92G
11415 Tallinn
Tel: + 372 606 1690
Fax: + 372 606 1691
Finland
OY GRUNDFOS Pumput AB
Mestarintie 11
FIN-01730 Vantaa
Phone: [phone]
Telefax: [phone]
France
Pompes GRUNDFOS Distribution S.A.
Parc d’Activités de Chesnes
57, rue de Malacombe
F-38290 St. Quentin Fallavier (Lyon)
Tél.: [phone]
Télécopie: [phone]
Germany
GRUNDFOS GMBH
Schlüterstr. 33
40699 Erkrath
Tel.: [phone]
Telefax: [phone]
e-mail: [e-mail]
Service in Deutschland:
e-mail: [e-mail]
HILGE GmbH & Co. KG
Hilgestrasse 37-47
55292 Bodenheim/Rhein
Germany
Tel.: [phone]
Telefax: [phone]
e-mail: [e-mail]
Greece
GRUNDFOS Hellas A.E.B.E.
20th km. Athinon-Markopoulou Av.
P.O. Box 71
GR-19002 Peania
Phone: [phone]
Telefax: +0030-210-66 46 273
Hong Kong
GRUNDFOS Pumps (Hong Kong) Ltd.
Unit 1, Ground floor
Siu Wai Industrial Centre
29-33 Wing Hong Street &
68 King Lam Street, Cheung Sha Wan
Kowloon
Phone: [phone]
Telefax: [phone]
Hungary
GRUNDFOS Hungária Kft.
Park u. 8
H-2045 Törökbálint,
Phone: [phone]
Telefax: [phone]
India
GRUNDFOS Pumps India Private Lim-
ited
118 Old Mahabalipuram Road
Thoraipakkam
Chennai 600 096
Phone: [phone]
Indonesia
PT GRUNDFOS Pompa
Jl. Rawa Sumur III, Blok III / CC-1
Kawasan Industri, Pulogadung
Jakarta 13930
Phone: [phone]
Telefax: [phone] / 460 6901
Ireland
GRUNDFOS (Ireland) Ltd.
Unit A, Merrywell Business Park
Ballymount Road Lower
Dublin 12
Phone: [phone]
Telefax: [phone]
Italy
GRUNDFOS Pompe Italia S.r.l.
Via Gran Sasso 4
I-20060 Truccazzano (Milano)
Tel.: [phone]
Telefax: [phone] / 95838461
Japan
GRUNDFOS Pumps K.K.
Gotanda Metalion Bldg., 5F,
5-21-15, Higashi-gotanda
Shiagawa-ku, Tokyo
141-0022 Japan
Phone: [phone]
Telefax: [phone]
Korea
GRUNDFOS Pumps Korea Ltd.
6th Floor, Aju Building 679-5
Yeoksam-dong, Kangnam-ku, 135-916
Seoul, Korea
Phone: [phone]
Telefax: [phone]
Latvia
SIA GRUNDFOS Pumps Latvia
Deglava biznesa centrs
Augusta Deglava ielā60, LV-1035, Rīga,
Tālr.: + 371 714 9640, 7 149 641
Fakss: + 371 914 9646
Lithuania
GRUNDFOS Pumps UAB
Smolensko g. 6
LT-03201 Vilnius
Tel: + 370 52 395 430
Fax: + 370 52 395 431

Grundfos companies
Malaysia
GRUNDFOS Pumps Sdn. Bhd.
7 Jalan Peguam U1/25
Glenmarie Industrial Park
40150 Shah Alam
Selangor
Phone: [phone]
Telefax: [phone]
México
Bombas GRUNDFOS de México S.A. de
C.V.
Boulevard TLC No. 15
Parque Industrial Stiva Aeropuerto
Apodaca, N.L. 66600
Phone: [phone]
Telefax: [phone]
Netherlands
GRUNDFOS Netherlands
Veluwezoom 35
1326 AE Almere
Postbus 22015
1302 CA ALMERE
Tel.: [phone]
Telefax: [phone]
E-mail: [e-mail]
New Zealand
GRUNDFOS Pumps NZ Ltd.
17 Beatrice Tinsley Crescent
North Harbour Industrial Estate
Albany, Auckland
Phone: [phone]
Telefax: [phone]
Norway
GRUNDFOS Pumper A/S
Strømsveien 344
Postboks 235, Leirdal
N-1011 Oslo
Tlf.: [phone]
Telefax: [phone]
Poland
GRUNDFOS Pompy Sp. z o.o.
ul. Klonowa 23
Baranowo k. Poznania
PL-62-081 Przeźmierowo
Tel: [phone]
Fax: [phone]
Portugal
Bombas GRUNDFOS Portugal, S.A.
Rua Calvet de Magalhães, 241
Apartado 1079
P-2770-153 Paço de Arcos
Tel.: [phone]
Telefax: [phone]
România
GRUNDFOS Pompe România SRL
Bd. Biruintei, nr 103
Pantelimon county Ilfov
Phone: [phone]
Telefax: [phone]
E-mail: romani[email protected]
Russia
ООО Грундфос
Россия, 109544 Москва, ул. Школьная
39
Тел. [phone]
Факс [phone]
E-mail [e-mail]
Serbia
GRUNDFOS Predstavništvo Beograd
Dr. Milutina Ivkovića 2a/29
YU-11000 Beograd
Phone: [phone] / 11 26 47
496
Telefax: [phone]
Singapore
GRUNDFOS (Singapore) Pte. Ltd.
25 Jalan Tukang
Singapore 619264
Phone: [phone]
Telefax: [phone]
Slovenia
GRUNDFOS d.o.o.
Šlandrova 8b, SI-1231 Ljubljana-Črnuče
Phone: [phone]
Telefax: [phone]
E-mail: [email protected]
South Africa
GRUNDFOS (PTY) LTD
Corner Mountjoy and George Allen
Roads
Wilbart Ext. 2
Bedfordview 2008
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Spain
Bombas GRUNDFOS España S.A.
Camino de la Fuentecilla, s/n
E-28110 Algete (Madrid)
Tel.: [phone]
Telefax: [phone]
Sweden
GRUNDFOS AB
Box 333 (Lunnagårdsgatan 6)
431 24 Mölndal
Tel.: [phone]
Telefax: [phone]
Switzerland
GRUNDFOS Pumpen AG
Bruggacherstrasse 10
CH-8117 Fällanden/ZH
Tel.: [phone]
Telefax: [phone]
Taiwan
GRUNDFOS Pumps (Taiwan) Ltd.
7 Floor, 219 Min-Chuan Road
Taichung, Taiwan, R.O.C.
Phone: [phone]
Telefax: [phone]
Thailand
GRUNDFOS (Thailand) Ltd.
92 Chaloem Phrakiat Rama 9 Road,
Dokmai, Pravej, Bangkok 10250
Phone: [phone]
Telefax: [phone]
Turkey
GRUNDFOS POMPA San. ve Tic. Ltd.
Sti.
Gebze Organize Sanayi Bölgesi
Ihsan dede Caddesi,
2. yol 200. Sokak No. 204
41490 Gebze/ Kocaeli
Phone: +90 - 262-679 7979
Telefax: +90 - 262-679 7905
E-mail: [e-mail]
Ukraine
ТОВ ГРУНДФОС УКРАЇНА
01010 Київ, Вул. Московська 8б,
Тел.:[phone]
Фах.: ([phone]
E-mail: [e-mail]
United Arab Emirates
GRUNDFOS Gulf Distribution
P.O. Box 16768
Jebel Ali Free Zone
Dubai
Phone: [phone]
Telefax: [phone]
United Kingdom
GRUNDFOS Pumps Ltd.
Grovebury Road
Leighton Buzzard/Beds. LU7 8TL
Phone: [phone]
Telefax: [phone]
U.S.A.
GRUNDFOS Pumps Corporation
17100 West 118th Terrace
Olathe, Kansas 66061
Phone: [phone]
Telefax: [phone]
Usbekistan
Представительство ГРУНДФОС в
Ташкенте
700000 Ташкент ул.Усмана Носира 1-й
тупик 5
Телефон: [phone]
Факс: [phone]
Revised 04.01.2012

www.grundfos.com
Being responsible is our foundation
Thinking ahead makes it possible
Innovation is the essence
The name Grundfos, the Grundfos logo, and the payoff Be–Think–Innovate are registrated trademarks
owned by Grundfos Management A/S or Grundfos A/S, Denmark. All rights reserved worldwide.
98150786 0212
ECM: 1088246