Gtech AirFOX Platinum AF01 User manual

OPERATING MANUAL
Model: AF01
5615_AirFOX_manual_aw.indd 15615_AirFOX_manual_aw.indd 1 09/10/2023 09:4609/10/2023 09:46

2
IMPORTANT SAFEGUARDS:
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE.
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
Do not use in rain or leave outdoors whilst raining.
WARNING: Basic safety precautions should always be observed when
using an electrical appliance, including the following to reduce the risk of fire,
electrical shock, or injury:
Personal Safety:
• Store indoors in a dry place out of the
reach of children.
• Always use responsibly. This appliance
can be used by children aged from 8 years
and above and persons with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe
way and understand the hazards involved.
• Don’t let children play with the appliance;
supervise children using or maintaining
the appliance.
• Use only manufacturer’s recommended
attachments as described in this
manual; misuse or use of any accessory
or attachment other than those
recommended, may present a risk of
personal injury.
• Take extra care when cleaning stairs.
• Keep the appliance and accessories away
from hot surfaces.
• Do not block the appliances openings
or hinder air flow; keep openings free of
any objects including dust, lint, clothing,
fingers (and all parts of the body).
• Particularly keep hair away from the brush
bar and other moving parts.
Electrical safety:
• Only use batteries and chargers supplied
by Gtech.
• Never modify the charger in any way.
• The charger has been designed for a
specific voltage. Always check that the
mains voltage is the same as that stated on
the rating plate.
• A charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack; never
use the charger with another appliance
or attempt to charge this product with
another charger.
• Before use, check the charger cord for
signs of damage or ageing. A damaged or
entangled charger cord increases the risk
of fire and electric shock.
• Do not abuse the charger cord.
• Never carry the charger by the cord.
• Do not pull the cord to disconnect from a
socket; grasp the plug and pull to disconnect.
• Don’t wrap the cord around the charger
when storing.
• Keep the charger cord away from hot
surfaces and sharp edges.
• The supply cord cannot be replaced. If the
cord is damaged the charger should be
discarded and replaced.
• Do not handle the charger or the
appliance with wet hands.
• Do not store or charge the appliance
outdoors.
• The charger must be removed from the
socket before removing the battery,
cleaning or maintaining the appliance.
• Ensure the appliance is off before connecting
or disconnecting the motorised brush bar.
Battery safety:
• This appliance includes Li-Ion batteries; do
not incinerate batteries or expose to
high temperatures, as they may explode.
• Liquid ejected from the battery may cause
irritation or burns.
• In an emergency situation contact
professional help immediately!
• Leaks from the battery cells can occur
5615_AirFOX_manual_aw.indd 25615_AirFOX_manual_aw.indd 2 09/10/2023 09:4609/10/2023 09:46

3
under extreme conditions. Do not touch
any liquid that leaks from the battery. If the
liquid gets on the skin wash immediately
with soap and water. If the liquid gets into
the eyes, flush them immediately with clean
water for a minimum of 10 minutes and seek
medical attention. Wear gloves to handle
the battery and dispose of immediately in
accordance with local regulations.
• Shorting the battery terminals may cause
burns or fire.
• When the battery pack is not in use, keep
it away from paper clips, coins, keys,
nails, screws or other small metal objects
that could make a connection from one
terminal to another.
• Store the battery away from any liquids
and chemicals that may damage the
battery and cause a risk of fire.
• Store the battery in clean, dry conditions,
within a recommended temperature range
of 0 - 25°C
• Do not store the battery in areas of high
temperature above 25°C. Do not store
near a source of heat or where exposed to
direct sunlight.
• When you dispose of the appliance remove
the battery and dispose of the battery safely
in accordance with local regulations.
Service:
• CAUTION – to reduce the risk of injury
from moving parts, remove battery before
servicing.
• Before using the appliance and aer any
impact, check for signs of wear or damage
and repair as necessary.
• Do not use the appliance if any part is
damaged or defective.
• Repairs should be carried out by a
service agent or a suitably qualified
person in accordance with relevant
safety regulations. Repairs by unqualified
persons could be dangerous.
• Never modify the appliance in any way as
this may increase the risk of personal injury.
• Only use replacement parts or accessories
provided or recommended by Gtech.
Intended use:
• This appliance has been designed for
domestic dry vacuum cleaning only.
• Do not pick up liquids or use on wet surfaces.
• Do not pick up anything that is flammable,
burning or smoking.
• Use only as described in this manual.
• Don’t use on concrete, tarmacadam
or other rough surfaces.
• The brush bar may damage certain floor
surfaces. Before vacuuming flooring, rugs or
carpets, check the flooring manufacturer’s
recommended cleaning instructions.
• The product may damage delicate fabrics or
upholstery. Care should be taken on loose-
weave carpets and coverings or where there
are loose threads. It is advised to test on an
inconspicuous area first before use.
• The product has been designed to clean
a wide variety of floor surfaces without the
need to change settings. However some
surfaces such as delicate loose-pile rugs or
carpets, tasselled rug edges or damaged
carpets with exposed threads are not
suitable for cleaning with a rotary brush.
• The product has a constantly rotating
brush bar. Never leave the cleaning head
in one spot for an extended period of time
as this may damage the floor surface.
• Particularly for hard flooring, before
vacuuming check the area being cleaned is
free of any hard debris or objects that could
damage the flooring if caught underneath
the product, and that the underside of the
product is free from foreign objects that
could mark the surface.
WARNING:
• Do not use water, solvents, or polishes to
clean the outside of the appliance; wipe
clean with a dry cloth.
• Never immerse the unit in water and do
not clean in a dish washer.
• Never use the appliance without the
filter fitted.
• Ensure the battery is removed before
changing tools.
• For household use only.
5615_AirFOX_manual_aw.indd 35615_AirFOX_manual_aw.indd 3 09/10/2023 09:4609/10/2023 09:46

4
Nick Grey – Inventor, owner of Gtech
Thank you for choosing Gtech
“Welcome to the Gtech family. I started Gtech to create sensible, easy
to use products that do a great job, and hope you get many years of
trouble-free performance from your new product.”
What’s in the box
Power floor head Hose
Wall mount
(3 pieces)
wall plugs
and screws
Hair removal
Tool
4
4
9
11
12
12
11
9
Battery Upholstery tool
2 7
AirFOX vacuum cleaner Brush tool
1 6
Crevice tool Charger
510
Power brush Extension tube
3 8
Make a note of your product serial number code for future reference._ - _ _ - _ _ _ ~
_ _ _ _ _ ~
_ _ _ _ ~
_ _ ~ _ _ _ _ _ _ _ X-XX-XXX~
XXXXX~
WWYY~
00~0000000
1
5
8
2
37
6
10
5615_AirFOX_manual_aw.indd 45615_AirFOX_manual_aw.indd 4 09/10/2023 09:4609/10/2023 09:46

5
To assemble the AirFOX into floor cleaning mode, attach the Power floor head, extension
tube and battery to the main vacuum.
Assembly
Tool configurations
Pay attention to correctly align
the conectors.
The tools can be fitted in a variety of cominations whether powered, like the floor head and
power brush, or inert like the hose, brush tool, upholstery tool and crevice tool.
5615_AirFOX_manual_aw.indd 55615_AirFOX_manual_aw.indd 5 09/10/2023 09:4609/10/2023 09:46

6
For short bursts of cleaning: press and hold
the power button to switch on.
Release the button to switch off.
Operation
For continuous operation: press and hold the
power button to switch on; press the lock
button from either side.
Press the lock button in the opposite direction
to switch off.
Gently pull the Power Brush from the product
to remove. The battery should be removed
when changing attachments.
Press the latch and pull to dis-assemble the
tube and accessory connections.
Power head removal
1
2
5615_AirFOX_manual_aw.indd 65615_AirFOX_manual_aw.indd 6 09/10/2023 09:4609/10/2023 09:46

7
Power Mode
AUTO
MAX
ECO
%
AUTO
MAX
ECO
%
AUTO
MAX
ECO
%
The mode button changes the power of the
AirFOX. While the vacuum is running touch
the mode button to cycle through the three
settings.
ECO – reduced power, longest run time
Auto – adjusts to optimum power for the dust
load conditions
Max – high power, shortest run time
AUTO
MAX
ECO
%
Push forward to pick up larger pieces of
debris. Pulling the vacuum back towards
you activates the AirLOC and picks up finer
particles.
For above the floor cleaning, you can fit the
crevice tool or dusting brush for reachable
areas or fit the extension tube with an accessory
for high up cleaning.
Operation
5615_AirFOX_manual_aw.indd 75615_AirFOX_manual_aw.indd 7 09/10/2023 09:4609/10/2023 09:46

8
Engage the tube into the floor head when
parking in the upright position.
The handle will only remain upright if the
interlocking notch and gap are engaged.
“Parking” the AirFOX
2
Power brush
Like the power floor head, it can be attached
directly to the AirFOX or to the extension tube.
The small power brush is attached and
removed in the same way as the power floor
head.
1
5615_AirFOX_manual_aw.indd 85615_AirFOX_manual_aw.indd 8 09/10/2023 09:4609/10/2023 09:46

9
To remove the battery press the latch and pull
the battery to remove from product.
Removing the battery Battery state of charge
Battery charging
The display shows how much charge the
battery has.
AUTO
MAX
ECO
%
2
1
The battery can be charged on the unit, off the unit, or on the wall mount. The battery can also
be charged via the wall mount.
5615_AirFOX_manual_aw.indd 95615_AirFOX_manual_aw.indd 9 09/10/2023 09:4609/10/2023 09:46

10
Hold the product over a rubbish bin and
release the latch to empty the dirt. A gentle
tap each time you empty the bin will help
remove excess debris.
Emptying the bin
If on the unit the display will show the capacity
during charging.
AUTO
MAX
ECO
%
When charging the battery has a flashing
green light.
When fully charged the light will be
continuous green.
5615_AirFOX_manual_aw.indd 105615_AirFOX_manual_aw.indd 10 09/10/2023 09:4609/10/2023 09:46

11
... and li the dust bin away from the product.
Cleaning the filter
If the display indicator flashes red and the
product powers off during use the filter might
need cleaning.
Release the lock button if necessary to power
off and reset the display.
Remove the battery.
Pull the lever...
AUTO
MAX
ECO
%
5615_AirFOX_manual_aw.indd 115615_AirFOX_manual_aw.indd 11 09/10/2023 09:4609/10/2023 09:46

12
Wash both the filter and filter shroud under a
tap with cold water.
Not suitable for a washing machine or
tumble dryer. Dry the filter completely
before re-fitting.
Tap the filter to remove any loose debris.
The filter can be gently brushed but do not rub
or scrub excessively.
Remove the filter assembly from the bin. Twist to release the metal shroud and pull away
from the filter.
Cleaning the filter
5615_AirFOX_manual_aw.indd 125615_AirFOX_manual_aw.indd 12 09/10/2023 09:4609/10/2023 09:46

13
Push the metal shroud onto the filter and twist
to lock in place.
Return the filter assembly to the bin, lining up
the tab on the filter with the recess in the bin.
Locate the dust bin onto the product and push
until it clicks into place.
Never use the product without the filter
fitted as you could damage the motor.
...checking it is correctly aligned.
2
1
5615_AirFOX_manual_aw.indd 135615_AirFOX_manual_aw.indd 13 09/10/2023 09:4609/10/2023 09:46

14
Clearing Blockages
If the suction is low or if the display indicator
flashes red and the product powers off during
use there may be a blockage.
Release the lock button if necessary to power off
and reset the display.
Remove the battery.
Remove the tube, floor head, dust bin, and
any accessory tools and check through the
openings for any blockages.
AUTO
MAX
ECO
%
5615_AirFOX_manual_aw.indd 145615_AirFOX_manual_aw.indd 14 09/10/2023 09:4609/10/2023 09:46

15
Removing and cleaning the brush bar
Slide the latch button inwards until the end
plate disengages, then remove the end plate.
The brushbar rotates up and out, and can be
removed for cleaning.
Removing the brush bar
If the brush bar jams during use the display
indicator will flash red and the product will
power off.
Release the lock button if necessary to power off
and reset the display. Remove the battery.
AUTO
MAX
ECO
%
Before re-starting clear the obstruction and
remove and clean the brush bar if necessary.
2
1
5615_AirFOX_manual_aw.indd 155615_AirFOX_manual_aw.indd 15 09/10/2023 09:4609/10/2023 09:46

16
The hair removal tool helps you cut any hair that
may become wrapped around the brushbar.
Never operate the product without the brush
bar in place.
While the brush bar is removed you can take
the opportunity to remove any hair from the
brush bar housing comb as indicated.
Push the latch into the slot by the brushbar
then clip into place.
Push the brushbar back into place, drive end
first.
Replacing the brush bar
2
1
5615_AirFOX_manual_aw.indd 165615_AirFOX_manual_aw.indd 16 09/10/2023 09:4609/10/2023 09:46

17
Removing the small power head brushbar
The brushbar can then be easily removed and
cleaned.
Using a coin or similar implement turn the end
cap until it unlocks and remove it.
5615_AirFOX_manual_aw.indd 175615_AirFOX_manual_aw.indd 17 09/10/2023 09:4609/10/2023 09:46

18
Wall mount
Install your wall mount at least 113cm from
the oor. Screws and wall plugs have been
included. Recommended drill size 6mm.
Check the wall area is free of water pipes
or electrical cables.
If unsure seek professional advice.
The wall mount will need a small amount of
assembly on attaching to the wall.
Consider position to be near a mains power
socket if want to charge on the wall mount.
113cm
minimum
height
The tools can be stored like this on the wall
mount.
5615_AirFOX_manual_aw.indd 185615_AirFOX_manual_aw.indd 18 09/10/2023 09:4609/10/2023 09:46

19
Product Care
Your product doesn’t need much maintenance: keep the filter clean, check for
blockages, remove hair from the brushbar and charge the battery. Wipe it with a dry
cloth if it gets dirty, including the area under the bin. Never wash it with liquid, run it
under a tap or use it without the filter.
To maintain optimum battery life store the battery in clean, dry conditions, within a
recommended temperature range of 0 - 25°C. Do not store the battery in areas of high
temperature above 25°C. Do not store near a source of heat or where exposed to
direct sunlight.
If the product will be stored for longer periods of time without use it is recommended
to fully charge the battery before storage to help maintain its condition and life.
Product is not cleaning well 1. Empty the bin
2. Check bin is correctly fitted
3. Check filter is correctly fitted
4. Clean the holes in the filter shroud
5. Clean and/or replace filter (See page 12)
6. Check for blockages
7. Check brush bar fitment
8. Clean and/or replace brush bar
Product has stopped
or won’t work – 0% on display
1. Battery is fully discharged
2. Recharge the battery
Product has stopped
or won’t work – flashing
red filter indicator
1. Clean the holes in the filter shroud
2. Clean and/or replace filter (See page 12)
3. Check for blockages (See page 14)
Product has stopped
or won’t work – flashing
red brush bar indicator
1. The brush bar is blocked or jammed (see
page 15)
2. Clear debris from the brush bar (See page 16)
3. Remove and clean brush bar (See page 16)
Battery will not charge – no
flashing green light
1. Check the charger is correctly connected
to the battery or wall mount.
2. Check the product is well seated on the
wall mount.
2. Check the charger is correctly connected
to the mains supply.
3. Check mains power socket is switched on.
4. Try another mains power socket.
Troubleshooting
5615_AirFOX_manual_aw.indd 195615_AirFOX_manual_aw.indd 19 09/10/2023 09:4609/10/2023 09:46

20
GTECH MULTI TECHNICAL SPECIFICATION
Battery model 271A001
Battery 37V Li-Ion
Charging period 5 hours
Battery charger output 42V DC 0.5A
Weight (with floor head) 2.9kg
[e-mail] chat supportOnline How to Videos
Product support
If these initial tips do not solve your problem we please visit our support area where you can find
troubleshooting help including online manuals, FAQs and how-to-videos, as well as genuine
spares and replacement parts compatible with your product.
Visit: www.gtech.co.uk/support
5615_AirFOX_manual_aw.indd 205615_AirFOX_manual_aw.indd 20 09/10/2023 09:4609/10/2023 09:46