GU Electronic Porsche CDR3.1 TD User manual

Porsche CDR3.1 TD
- MODEL : CDR-31-190521
- DATE : 2020.09.24

GU Electronic
Index
1. Main Spec
2. Block Diagram
3. Dimension
4. External Appearance
5. Connector Pin Assignment
6. Product Composition
7. DIP S/W Setting
8. Mode Change
9. Touch Control
10. OSD(On Screen Display) Control
11. Install Manual
12. Q & A

GU Electronic
1. Main Spec.
1. Input Spec. (MULTI VIDEO INTERFACE)
- 1 x Digital RGB Input (Navigation System source)
- 1 x Analog RGB Input (Navigation System output)
- 2 x A/V Input (External video source)
- 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
- 1 x CVBS(FRONT CAMERA) Input. (Front camera source)
- 1 x LVDS Input. (Car Command System)
2. Output Spec.
- 2 x CVBS Output (Video out for Installing Headrest Monitor)
- 1 x Audio L/R Output.
- 1 x Vertual Analog Touch (Navigation System source)
- 1 x Uart Digital Touch (Navigation System source)
- 1 x LVDS Output (LCD Operation)
3. Power Spec.
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12Watt, Max
4. Switch Input mode
- Possible to select CAR model while switching mode by DIP S/W
- By button on the Commander in the car via CAN

GU Electronic
2. Block Diagram
Scaler
(PIP)
MCU
INTERFACE
CAR
COMMAND
SYSTEM CAN
EEPROM
CAN
RECEIVER
LVDS
TX
REAR CAMERA
POWER
REAR CAMERA
LVDS
LVDS
FRONT CAMERA COMPOSITE
NAVIGATION
SYSTEM
COMPOSITE
CVBS1
CVBS2 MUX
CAR
TFT-LCD
SUB
BOARD
RELAY

GU Electronic
3. Dimension
164mm * 83mm * 21mm
* This can change under manufacturer’s circumstance
164mm
21mm
83mm

GU Electronic
4. External Appearance
Analog
NAVI
AV(IN/OUT)
Digital
NAVI
LED IMAGE LVDS-OUTRGB-OUT
DIP S/W PROGRAM
TOUCH Mode S/WPOWER

GU Electronic
4. External Appearance
Analog
NAVI
AV(IN/OUT)
Digital
NAVI
TOUCH Mode S/WPOWER
LVDS-OUT RGB-OUT LEDIMAGE PROGRAM DIP S/W

GU Electronic
5. Connector Pin Assignment
*POWER Connect
① ACC (Red)
② GND (Black)
③ N.C
④ N.C
⑤ REAR VCC (Red)
⑥ N.C
⑦ REAR-CAM DETECT (Brown)
⑧ N.C
⑨ FRONT-CAM DETECT (Blue)
⑩ FRONT VCC (Red)
①②③④⑤⑥⑦⑧⑨⑩
*NAVI Connect
① R DATA (Red)
② G DATA (Green)
③ B DATA (Blue)
④ SYNC (White)
⑤ GND (Black)
⑥ DVB-T-IR
⑦ DVD-IR
①②③④⑤⑥⑦
*Touch Connect
① Y-
② X-
③ Y+
④ X+
① ② ③ ④

GU Electronic
6. Product Composition
Interface 1 EA
A/V Cable 1 EA
RGB Navi Cable 1 EA LVDS Cable(800mm) 1 EA
Power Cable 1 EA
OSD Board 1 EA
SUB Board 1 EA
FPC Cable 1 EA
FFC Cable 1 EA
RGB Sub Cable 1 EA
SUB 4PIN 1EA
Mode S/W 1 EA

GU Electronic
6. Product Composition
* CarPlay Set Sales(option) – KPLAY
Interface 1 EA AUX Cable 1 EA
Power Cable 1 EA HDMI Cable 1 EA
Microphone 1 EA
Bluetooth / Wifi Antenna 2EA

GU Electronic
6. Product Composition
CarPlay Main 1 EA AUX Cable 1 EA
Power Cable 1 EA
HDMI Cable 1 EA
* CarPlay(NV17) Set Sales(option)
Microphone 1 EA

GU Electronic
7. DIP S/W Setting
* ON : DOWN , OFF : UP
PIN FUNCTION DIP S/W Selection
1 NAVI ON : Not Used
OFF : Used
2 DVB-T(AV1) ON : Not Used
OFF : Used
3 DVD(AV2) ON : Not Used
OFF : Used
4 N.C
5 N.C
6
CAR type SEL Right Picture7
8
* DIP S/W Example
CDR3.1

GU Electronic
8. Mode Change
Mode Change Button
Return OEM dispaly mode change(Long Press)

GU Electronic
9. Touch Control
Press and hold for more than 11 seconds on
NAVI, DVB-T, DVD screen.
(Note that it only works the first time after
switching screens)
+ Touch according to the shape coordinates
.
OR
OSD menu -> Utility -> Calibration
Touch control - Calibration

GU Electronic
9. Touch Control
DVB-T/DVD Control
Press Icon
DVB-T DVD

GU Electronic
10. OSD(On Screen Display) Control
OSD control
Mode State
First Menu Second Menu Third Menu
MENU Press to display when there is no OSD
screen.
When OSD screen is on, press it to EXIT or
OFF.
SEL Item Selection, Value Selection
UP Item up
Increase selected value
DOWN Item down
Decrease selected value
MENU SEL UP DOWN

GU Electronic
First Menu Second Menu Third Menu Description
Config
NAVI-RGB DIGTAL-INAVI
:Setting the Connected NAVI Model
DVB-T(DMB) ELT_DVBT20
:Setting the Connected DVB-T Model
DVD ELT_980XU Slim
: Setting the Connected DVD Model
RearCam AVM VIDEO
: Setting the Connected RearCam Model
Reset Execute Reset to default value of Config menu
OSD Config
10. OSD(On Screen Display) Control

GU Electronic
OSD - Option Menu
First Menu Second Menu Third Menu Description
Option
NAVI COM
HMS
FINE
:
Set up manufacturer of
woodworking device for UART
Touch use
OFF Do not use features.
RearCam-Type OEM Original Camera
ExtDevice Equipped with external camera
RearCam-Power
ON + 12V continuous supply
AUTO + 12V supply only in Rear
camera mode
OFF + 12V off
RearCam-Det GEAR Detected by CAN
WIRE Detected by Rear-Det Wire
FrontCam-Type OEM Original Camera
ExtDevice Equipped with external camera
FrontCam-Power
ON + 12V continuous supply
AUTO + 12V supply only in Front
camera mode
OFF + 12V off
FrontCam-Det GEAR Detected by CAN
WIRE Detected by Front-Det Wire
10. OSD(On Screen Display) Control

GU Electronic
OSD - Option Menu
First Menu Second Menu Third Menu Description
Option
AV Out
AV1 In the OEM, NAVI, AV1, FRONT,
and REAR modes, the output of
AV OUT is set to AV1.
AV2 In the OEM, NAVI, AV2, FRONT,
and REAR modes, the output of
AV OUT is set to AV2.
USER In the OEM, NAVI, FRONT, and
REAR modes, output the output
of AV OUT to the final screen.
UI DVB-T (DMB) ON DVB-T device control UI output
function
OFF Disable feature
UI DVD ON DVD device control UI output
function
OFF Disable feature
Reset Execute Option Menu all Reset
10. OSD(On Screen Display) Control

GU Electronic
First Menu Second Menu Third Menu Action
Image
Brightness Adjust the value of brightness
Contrast Adjust the value of contrast
Color-RED Adjust the value of RED
Color-GREEN Adjust the value of GREEN
Color-BLUE Adjust the value of BLUE
Reset Excute Option Menu all Reset
First Menu Second Menu Third Menu Action
Image
Brightness Adjust the value of brightness
Contrast Adjust the value of contrast
Saturation Adjust the value of Saturation
Hue Adjust the value of Hue
Sharpness Adjust the value of Sharpness
Reset Excute Option Menu all Reset
NAVI-RGB menu
DVD,DVB-T(DMB),NAVI-AV,REAR,FRONT menu
<< Brightness >>
<< Contrast >>
<< Saturation >>
10. OSD(On Screen Display) Control