Guardian BEAM V2 User manual

Smart Control Kit Installation Guide
adhguardianusa.com
1-424-272-6998
TM
Item No: V2
Installation requires no special tools—you’ll just need a
screwdriver, stepladder and smartphone!

Please read and follow all installation instructions. These
instructions include your secure Blackbox Code. Homeowners
should retain this guide for reference.
Date Installed: _____________________
Thank you for purchasing the beam Smart
Control Kit!
Warning:
To reduce the risk of injury to persons:
• Use this Smart Garage Door Controller only with Residential Sectional
Garage doors.
• Do not enable this device on a one-piece or swinging garage door.
• Do not use this device on garage door openers made before 1993 without
a working photo-eye safety system.
Register your Smart Control Kit online at:
adhguardianusa.com/warranty-information

Unbox the contents of your kit
Your kit should contain two AAA batteries and the following:
A. Blackbox controller
B. Power adapter
C. Wireless door sensor
D. Opener cable
1

Mount the Blackbox controller
• Locate the Blackbox and grab your stepladder.
• Clean and wipe dry your selected mounting location, either on
the garage door opener or a nearby surface. Mount using the
adhesive strips on the back of the Blackbox.
TIP: The Blackbox should be mounted within 6 feet of the
garage door opener and a power source. All input ports and
LEDs should be visible and accessible aer mounting.
2
Mounting location
options

• Locate the opener cable .
• Plug the black connector into the Blackbox “OPENER” port.
3Connect the opener cable to the
Blackbox controller
OPENER DC IN
I/OSTATUS

• Unplug your garage door opener.
• Using your screwdriver, connect the other end of the opener
cable to your garage door opener push button terminals.
4
TIP: View sample connection diagrams for other
garage door opener makes and models at:
adhguardianusa.com/beam
Connect the Blackbox controller to the
garage door opener
PUSH BUTTON

Power up the Blackbox controller
• Locate the power adapter and plug into the DC IN port on
the Blackbox .
• Plug the other end of the power adapter into the closest
power source. The status LED on the side of the Blackbox
should begin to blink orange for setup.
• Plug back in your garage door opener.
5

Connect to WiFi
• Download the beam app from the App Store (iOS) or
Google Play (Android).
• Open the app and select “Setup Your Smart Control Kit.”
• Follow prompts within the app to select your wireless network
and enter your network password.
TIP: If you are a professional installer, setup in the beam app
should be done using the homeowner’s smartphone.
6

Point screen at
sensor now!
3
Program the Blackbox controller
• Follow prompts within the app to program the Blackbox .
• When directed, press your phone screen tightly against the
bottom setup port.
TIP: If setup is successful, the Blackbox’s status LED will
flash green and there will be an audible beep. If setup is not
successful, you will be guided through setup again.
7

Scan the wireless door sensor code
• Locate the wireless door sensor .
• Follow prompts within the app to create an account and scan
the Sensor Code found on the back of the sensor.
• Enter a name to identify that door within the app.
8

Mount the wireless door sensor
• Clean and wipe dry an area at the top of your garage door’s
interior panel.
• Remove the battery tab from the back of the wireless door
sensor and mount to the cleaned area of the garage door
using the adhesive Velcro strips. All done!
9
Mounting location

Get the most from your beam Smart Control Kit!
• Share access with others – Invite friends and family within the
app. No need to share your code or buy additional remotes.
• Explore integrations – beam plays well with others, from
IFTTT to Amazon Alexa.
For more information, go to:
adhguardianusa.com/beam
©2018, ADH Guardian USA LLC
Guardian Access & Door Hardware I 122 Penn Street I El Segundo, CA 90245