Guepard Networks GC300N User manual

www.guepardnetworks.com

1|Page

GC300N MANUAL
300MbpsCEILINGACCESSPOINT
ComplywithIEEE802.11b/g/nstandard
Model:GC300N




ProfessionalQualcommChipset
ComplywithIEEE802.11b/g/nstandard



HOSPITALITY HOME  PUBLIC GENERALITY FACTORY

www.guepardnetworks.com

2|Page

GC300N MANUAL
1
st
HardwareandOperationmodeInstruction
1)Hardwareinterface

DCPower:DCpowerconnector
LEDLights:LEDIndicatorofWANportandLANportusing.
WAN:GigabitWAN/POEPortthisportusingconnectwithADSLmodemorInternetmainlyoroverPOE
adaptor(ifdonotuseDCPowerconnector).
LAN:GigabitLANPortformorecableendusers.
ResetButton(RST):itmakeAPreverttofactorydefaultafterpressandholdit15seconds.


LEDindicator
‐PowerIndicator
‐Wi‐FiIndicator
‐WanIndicator
2)HowtosupplydataandpowertoGC300N?
TheconnectiondiagramshowedasP1,internetcableconnecttoPoEadapter’sLANPort,GC300N’s
WANportconnecttoPOEadapter’sPOEPort,thenenduserswillaccessintoGC1200acthroughcable
(GC300N’sLANport)orwireless(2.4GHz).

www.guepardnetworks.com

3|Page

GC300N MANUAL

P1
Pleasenote:iftheWirelessAPsupport24VpassivePoEthenthePoEadaptershouldbe24VPassivePoE.
IfthewirelessAPsupport48VIEEE802.3afstandardPoEthenthePoEadaptershouldbe48VPoEstandard.
3)HowtosetupGC300Noncelling?
Setupasguidingpictureasbelow:


www.guepardnetworks.com

4|Page

GC300N MANUAL
Operationmodes
Operationasdiagramasbelow:

P2.Operationmodesdiagram
TherearethreeoperationmodeonthiswirelessAP:
‐Gatewaymode:ThecableinternetcanbetransmittedtowirelessinternetthroughPPPOE,StaticIP,
andDynamicIP.Theconnectiontopologyisshowedasfollows:ConnectInternetcabletoCeiling
AP’sWANport,PCorenduserconnectwithCeilingAPthroughwired/wireless(2.4GHz).
‐APMode:plugandplay,suitableforhotel,school,andshoppingmallandsoon.Theconnectionis:
theinternetcableisconnectedfromrouter/switchtoceilingAP,thenceilingAPwilltransmitWi‐Fi
signal,PCandendusercanaccessintointernetbywired/wireless(2.4GHz).
‐RepeaterMode:TheceilingAPcanextendtheexistingWi‐Firangeifitssignalisweak.The
connectionshowsasabove:CeilingAPcansearchtheexistingWi‐Fisignalthenconnectit’s
wirelessly,thenPCorendusercanaccessintoceilingAPwireless(2.4GHz)/wired.
HowtoconnectGC300NWirelessAP
UserscanconnectthePC/Laptop/Smartphone/Tablet…withwirelessAPbyWirelessSSIDandLAN
cable:ThedefaultSSIDisGC300Nfor2.4GHz,SSID’spasswordis66666666(numbersixeight
times).

www.guepardnetworks.com

5|Page

GC300N MANUAL
2stGUILogin(GraphicUserInterface)
1）Choosetheproperpowersupplymodeandoperationmode
2）AssignanIPaddressforlocalPC
FollowingstepswillshowhowtoassignanIPaddress(staticIP)forPCafterconnectwirelessAPandPC
bywiredcableorwireless:configurelocalIPaddressas192.168.188.X(Xcanbeselectedfrom2‐252)
thesamenetworksegmentasceilingAP,subnetmask255.255.255.0,AsP3andP4shows.

P3.CheckLocalAreaConnectionorOpennetworkandsharingcenter(Win10)

P4.AssignIPaddressforPC(Suchas:192.168.188.100)
3)OpenInternetExplorer(IE),Chrome,Firefox…andinput
192.168.188.253(thisisIPdefaultofWirelessAP)ontheaddressbar,thenpressEnter,alogin
pagewillpopup,inputadmininLogincell,thenpressEnterorLoginbuttononAdmininterface.

www.guepardnetworks.com

6|Page

GC300N MANUAL

P5.Logininterface.
3rdSettingsGUI(GraphicUserInterface)
1)Status:Afterlogin,thenP6DeviceStatuswillbeshowed:

P6.Info‐graphicofDeviceStatus.

www.guepardnetworks.com

7|Page

GC300N MANUAL
Detailofindexes:
Topmenu:
‐Status:listingallindexesandstatusofwirelessAP.
‐Wizard:ShortcutforswitchingwirelessAP’soperationmode.
‐Advanced:alloffeatureswhichconfigurewirelessAP.
‐Exit:outofadministrationinterface.
NextIndexesrowbelow:
‐GatewayMode:currentwirelessAPmodestatus.
‐Channel1:currentwirelessAPchannelin2.4GHzband.
‐Reboot:clickthisbuttonifyouwanttorebootdevice.
NextInfo‐graphicbelow:
‐User:numberofusersconnectedWirelessAPandusinginternet.(Ex:01usersonP6)
‐Greenmark:usersconnectedLANstable(Redmark:disconnected).
‐Router:WirelessAPrunasrouterrole.
‐Green mark (DHCP): Wireless AP connected modem with “DHCP WAN connect type” stable (Red
mark:disconnected).
NextIndexesrowbelow:
‐Runningtime:totaltimeWirelessAPhadrun.
‐SoftwareVersion:versionofGuepardNetworks’sfirmware.
NextInfographicbelow:
‐CPUusage:runningstatusofCPU(percent).
‐2.4WirelessSettings:indicatenumberofusersconnected2.4GHzband,SSID,MACaddressandfast
configuration:theSSID,bandwidth,channel,encryption,passwordthenApplytofinish.
‐LANSettings:indicatenumberofuserswasassignedIPbyWirelessAPandfastconfiguration:wireless
AP’sIP,subnetmask,DHCPstatus,DHCPClientIPStart–End,LeaseTime(hour)thenApplytofinish.
‐WAN Settings: indicate IP WAN of wireless AP and WAN access mode, fast configuration: PPPoE,
DHCP,StaticIP.
2)Wizard:ShortcutforswitchingwirelessAP’soperationmodes.
ClickWizardinStatuspagewillhavepop‐upfollowingpagetoconfiguretheoperationmode:
TherearefouroperationmodeofceilingwirelessAPandthereareexplanationforeachoperationmode
forbetteruse,seeP7below:

www.guepardnetworks.com

8|Page

GC300N MANUAL

P7.SwitchingfunctionbetweenwirelessAP’soperationmodes. 
TherearefouroperationmodesofceilingwirelessAPandthereareexplanationforeachoperation
modeforbetteruse.
‐GatewayMode:Inthismode,thedeviceissupposedtoconnecttointernetviaADSL/CableModem.
TheNATisenableandPCsinLANportssharethesameIPtoISPthroughWANport.Theconnection
typecanbesetupinWANpagebyusingPPPOE,DHCPclientorstaticIP.
ConfigurationdescribeonP8,P9,P10andP11asfollowing:

P8.WANsettinginGatewayMode.

www.guepardnetworks.com

9|Page

GC300N MANUAL

P9.WirelessSettingsfor2.4GHzbandinGatewayMode.

P10.CompletethesettinginGatewayMode.

P11.StatusinGatewayMode.

www.guepardnetworks.com

10|Page

GC300N MANUAL
‐RepeaterMode:Inthismode,theusercanaccesswirelessAP,devicecanbeconnectedtoother
wirelessnetworkusingthewireless.Allinterfacesarebridgedtogether.WithoutNAT,firewallandall
networkrelatedfunctions.
ConfigurationdescribeonP12,P13,P14andP15asbelow:
ClickRepeatermodeinWizard,thenfollowingpagewillpopupandchoosetherightSSID(click
ScanAPbutton)tobridge.
Note:DonotcheckWDSpassthroughifyoudonotknowthisfunction.

P12.WirelesssettingsinRepeaterMode
AndthenclickNexttofinish.Re‐loginAdministratorinterfaceconfigureSSID(inthiscase,weconfigure
SSID“GuepardNetworks”)forusers.

P13.StatusinRepeaterMode