Gulf Coast Fans 4YU26 User manual

WARNING : READ AND SAVE THESE INSTRUCTIONS.
Follow these instructions carefully and be mindful of all warnings shown throughout.
WARNING :READ AND SAVE THESE INSTRUCTIONS.
Follow these instructions carefully and be mindful of all warnings shown throughout.
4YU26
Owners Manual
UL
R
Total fan weight
3.5 KGS.
4.5 LBS.

WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
PLEASE OBSERVE THE FOLLOWING :
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
PLEASE OBSERVE THE FOLLOWING :
READ AND SAVE THESE INSTRUCTIONSREAD AND SAVE THESE INSTRUCTIONS
1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan can be made to work immediately after installation - the bearings are adequately charged
with grease. So that, under normal conditions, further lubrication should not be necessary
10]. The fan must be turned off and stopped before reversing fan direction.
11. This fan is suitable for indoor location use.
P1

Yoke cover
5. Yoke & Downrod Assembly
Fan assembly
Canopy
Downrod Set Screw
Cross Pin
Yoke
Downrod
Cotter Pin
Blade holder
Blade
Mounting Bracket
Canopy
1.Unpack and inspect fan carefully to be certain all contents are
included.
Yoke
Cotter Pin
Cross Pin
Downrod
Wires
Yoke cover
OFF OFF OFF
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable for
fan support.
Secure outlet box directly to the
building structure using wood
screws (included).
Outlet box must support 40 lbs
min.
Install mounting bracket
to Outlet box in ceiling
using washers and the
mounting screws
provided with the outlet
box.
2. 3.
4.
Do not use existing
mounting bracket,
replace it with new
mounting bracket from
box.
Do not use existing
mounting bracket,
replace it with new
mounting bracket from
box.
Outlet Box
Mounting
Bracket
(2)
Insert the cross pin through yoke & downrod
and secure with cotter pin.
(3)
Tighten both downrod set screws to further
secure downrod, then pull down the yoke
cover to cover yoke.
P2
Mounting Screw 2pcs
Spring Washer 2pcs
Lock Washer 2pcs
Mood Screw 2pcs
Tooth Washer 2pcs
Blade Balance Kits 1pcs
Blade Screw 13pcs
Paper Washer 13pcs
Wire nuts 3pcs
Pull Chain Knob 1pcs
Motor screw 9pcs
Hardware bagHardware bag
Switch Housing Cover
(1)
Take cotter pin and cross pin off
downrod assembly.
downrod
(2)
Feed motor lead wires through yoke cover ,
canopy, and insert downrod into yoke.
Downrod

6-1.
Lift fan assembly onto
mounting bracket.
6-2.
Carefully lift fan assembly onto mounting bracket.
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
Mounting
Bracket
6. Hanging the fan
8-1.Push up the Canopy until the two screws on mounting bracket
are engaged with Key Holes in canopy.
8-2.Rotate the canopy slightly until the two screw heads
are in the small end of the Key Holes.
8-3.Tighten both screws. Canopy
Key Holes
Screw
8. Install the canopy
P3
Attach blade to blade arm with screws
& rubber washers provided in hardware bag.
Make sure that all screws are firmly tightened.
9. Blades installation
Blade
Blade Screw
Rubber Washer
Blade Holder
Ridge
Ball Groove
Mounting
Bracket
7. Make wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
: Wires from house may vary in color and may not include ground wire ( green ).
After wiring is completed, gently push wires into junction box with nuts pointing upward.
Note
From House
White
Black
From Fan
White
Black
Blue
Secure with twist - lock wire nuts. (Included)Secure with twist -lock wire nuts. (Included)
Green
Green
Green
(AC-N)
(AC-L)
( from downrod )
( from mounting bracket )
( for ground wire )
( for light kit )
(Motor-N)
(-L)Motor

P4
Remove 3pcs of motor stoppers.
Attach the blade assembly to motor using
motor screws from hardware bag firmly.
10. Blade assembly to motor
13. Turn on the power, your fan is ready for operation.
Motor screw
Blade Assembly
Motor stopper
12.Connect pull chain knob to pull chain.
Pull Chain Knob
*NOTE: Do not bend blade or blade arm to prevent wobble.
Insert wires existing from Light Kit Fitter by passing through center hole and
attach Light Kit Fitter to Switch Housing Cover with threaded tube and /or
fasten with spring washer and hex nut.
11. Make wire connections for light kit (if this fan equips with light kit)
Terminal Block Style ---- Loosen screws on Terminal
Block first, for accepting new wires from Light Kit.
( 1 ). Insert white wire from Light Kit into terminal block
extending from orange or white wire from fan
and tighten by screw on terminal block.
( 2 ). Insert black wire from Light kit into terminal block
extending from brown or blue wire from fan and
tighten by screw on terminal block.
Attach Light Kit and Switch Housing Cover assembly to
Switch Housing and secure with three original screws.
Terminal Block Style
Switch Housing.
Screw
Switch
Housing
Cover
White or
Orange Wire
White Wire
Light Kit
Fitter
Terminal block
Small Screw Driver
Black Wire
Blue or Brown Wire