H3C HIM-8FE User manual

H3C SR6600/SR6600-X Routers
Interface Module Guide
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W111-20220412

Copyright © 2007-2022, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this
document are the property of their respective owners.
Notice
The information in this document is subject to change without notice. All contents in this document, including
statements, information, and recommendations, are believed to be accurate, but they are presented without
warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions
contained herein.

Preface
This document describes the modules (such as HIM, MIM, MIC, MIC-X and SAP) supported by the
H3C SR6600/SR6600-X routers, the interface cables, and the compatibility matrices among the
modules, flexible interface platforms (FIPs), main processing units (MPUs), and the routers.
This preface includes the following topics about the documentation:
•
Audience.
•
Conventions.
•
Documentation feedback.
Audience
This documentation is intended for:
•
Network planners.
•
Field technical support and servicing engineers.
•
Network administrators working with the routers.
Conventions
The following information describes the conventions used in the documentation.
Command conventions
Convention
Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select a minimum of one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntaxchoices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.

GUI conventions
Convention
Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window opens; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create >
Folder.
Symbols
Convention
Description
WARNING! An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION:
An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT:
An alert that calls attention to essential information.
NOTE:
An alert that contains additional or supplementary information.
TIP:
An alert that provides helpful information.
Network topology icons
Convention
Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
T
T
T
T

Convention
Description
Represents a security module, such as a firewall, load balancing, NetStream, SSL
VPN, IPS, or ACG module.
Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model,
configuration, or software version. It is normal that the port numbers, sample output, screenshots,
and other information in the examples differ from what you have on your device.
Documentation feedback
You can e-mail your comments about product documentation to inf[email protected]om.
We appreciate your comments.

i
Contents
H3C SR6600/SR6600-X router interface modules·········································1
HIMs···································································································································································1
HIM-8FE·····················································································································································1
HIM-4GBE/HIM-8GBE ·······························································································································2
HIM-4GBP/HIM-8GBP ·······························································································································4
HIM-1EXP ··················································································································································6
HIM-CL1P/HIM-CL2P·································································································································7
HIM-CLS1P/HIM-CLS2P··························································································································10
HIM-MSP2P/HIM-MSP4P························································································································12
HIM-PS1P················································································································································14
HIM-AL1P/HIM-AL2P·······························································································································15
HIM-RS2P················································································································································17
HIM-4G4P················································································································································18
HIM-TS8P ················································································································································20
HIM-8GBP-V2··········································································································································21
HIM-4GBP-V3/HIM-8GBP-V3··················································································································23
HIM-4GBE-V3/HIM-8GBE-V3··················································································································24
HIM-16GBP··············································································································································26
HIM-2EXP ················································································································································28
MIMs ································································································································································29
MIM-2GBE ···············································································································································29
MIM-8E1(75)/MIM-8E1(75)-F···················································································································30
MIM-8T1/MIM-8T1-F································································································································32
MIM-1CE3················································································································································34
MIM-1CT3················································································································································35
MIM-1T3-V2·············································································································································37
MIM-2SAE/MIM-4SAE/MIM-8SAE···········································································································39
MICs·································································································································································41
MIC-GP4L················································································································································41
MIC-GP8L················································································································································43
MIC-XP4L·················································································································································44
MIC-QP1L················································································································································44
MIC-SP4L·················································································································································45
MIC-SP8L·················································································································································47
MIC-Xs ·····························································································································································48
MIC-X-GP4GT4········································································································································48
MIC-X-GP8···············································································································································49
MIC-X-GP10·············································································································································50
MIC-X-XP2···············································································································································51
MIC-X-XP4···············································································································································52
MIC-X-XP4W············································································································································53
MIC-X-GT8···············································································································································53
MIC-X-CLP2·············································································································································54
MIC-X-CLP4·············································································································································55
MIC-X-SP4···············································································································································56
MIC-X-SP8···············································································································································57
MIC-X-ET16·············································································································································58
MIC-X-CNDE-SJK····································································································································59
MIC-X-Adapter·········································································································································60
Connecting interface cables·········································································61
Connecting an Ethernet interface cable···········································································································61
Connecting an optical interface cable··············································································································62
Connecting an E1 interface cable····················································································································65
Connecting a T1 interface cable ······················································································································68
Connecting a CE3/CT3/T3 interface cable·······································································································69
Connecting a serial interface cable··················································································································69

ii
Interface module technical specifications·····················································73
Compatibility matrixes on Comware 5··························································76
LPU and router compatibility matrix·················································································································76
LPU and MPU compatibility matrix ··················································································································77
MPU and router compatibility matrix················································································································77
Compatibility matrixes on Comware 7··························································79
LPU and router compatibility matrix·················································································································79
LPU and MPU compatibility matrix ··················································································································80
MPU and router compatibility matrix················································································································80
Interface module and Comware compatibility matrix····································82
Interface module and FIP compatibility matrix ·············································84
Interface module&SAP and transceiver module compatibility matrix············86
QSFP+ transceiver modules····························································································································92
XFP transceiver modules·································································································································93
SFP+ transceiver modules·······························································································································93
SFP transceiver modules·································································································································94

1
H3C SR6600/SR6600-X router interface
modules
CAUTION:
•
The MIM interface modules are not hot swappable.
•
The MIC interface modules are hot swappable. You can hot swap all MIC interface modules
except for the MIC-X-CNDE-SJK directly. Before removing a MIC-X-CNDE-SJK interface module
during device operation, press and hold the REMOVE button on the module until the RUN LED
turns off.
•
Before removing a HIM interface module during device operation, execute the remove
command for the module.
NOTE:
The LPU, MPU, and router compatibility matrixes vary by Comware system
. For more information,
see "Compatibility matrixes on Comware 5" and "Compatibility matrixes on Comware 7."
HIMs
HIM-8FE
The HIM-8FE is a 10BASE-T/100BASE-TX Fast Ethernet (FE) interface module used by a router to
communicate with a LAN. It provides eight RJ-45 ports, each of which supports the Layer 3 routing
function and has a bi-color status LED.
The HIM-8FE has the following features:
•
The transmission distance can be up to 100 meters (328.08 ft) if a category-5 twisted pair cable
is used.
•
The interfaces support 10/100 Mbps auto-sensing.
•
The interfaces typically operate in full duplex mode and can also operate in half duplex mode.
Front panel
Figure 1 Front panel
(1) FE port
(2) FE port status LED
(3) Captive screw
(4) Ejector lever
12 3
4

2
LEDs
Table 1 LED description
LED status
Description
Off No link is present or the cable is faulty.
Steady yellow A 10 Mbps link is present.
Flashing yellow Data is being received or transmitted at 10 Mbps.
Steady green A 100 Mbps link is present.
Flashing green Data is being received or transmitted at 100 Mbps.
Interface specifications
Table 2 Interface specifications
Item
Specification
Connector type RJ-45
Number of interfaces 8
Interface standards 802.3, 802.3u
Interface type Auto MDI/MDI-X
Cable type Straight-through/crossover cable
Transmission distance 100 m (328.08 ft)
Interface speed and duplex mode •10/100 Mbps auto-sensing
•Full duplex/half duplex
NOTE:
The
medium dependent interface (MDI) standard is typically used on the Ethernet interface of
network adapters; the
medium dependent interface crossover (MDI-X)
standard is typically used on
hubs or LAN switches.
Interface cables
The HIM-8FE uses a category-5 straight-through cable or crossover Ethernet cable. For the
appearance and connection of a HIM-8FE interface cable, see "Connecting an Ethernet interface
cable."
HIM-4GBE/HIM-8GBE
The HIM-4GBE and HIM-8GBE are 10BASE-T/100BASE-TX/1000BASE-T auto-sensing Ethernet
interface modules. A HIM-4GBE provides four, and a HIM-8GBE provides eight, RJ-45 ports that
support Layer 3 routing. Each port is provided with a bi-color LED indicating the running status of the
port. The HIM-4GBE or HIM-8GBE is connected to the processor through a 10-Gbps high-speed bus
and can provide all high-performance Layer 3 Ethernet interface functionalities.

3
Front panels
Figure 2 Front panel of HIM-8GBE
(1) GE port
(2) GE port status LED
(3) Captive screw
(4) Ejector lever
Figure 3 Front panel of HIM-4GBE
(1) Captive screw
(2) GE port
(3) GE port status LED
(4) Ejector lever
LEDs
Table 3 LED description
LED status
Description
Off No link is present or the cable is faulty.
Steady green A 1000 Mbps link is present.
Flashing green Data is being received or transmitted at 1000 Mbps.
Steady yellow A 10/100 Mbps link is present.
Flashing yellow Data is being received or transmitted at 10/100 Mbps.
4
1 2 3
2
1
4
3

4
Interface specifications
Table 4 Interface specifications
Item
Specification
Connector type RJ-45
Number of interfaces •HIM-4GBE: 4
•HIM-8GBE:8
Interface standards 802.3, 802.3u, 802.3ab
Interface type Auto MDI/MDI-X
Cable type Straight-through/crossover Ethernet cable
Transmission distance 100 m (328.08 ft)
Supported frame format •Ethernet_II
•Ethernet_SNAP
Interface speed and duplex mode
10 Mbps Full/half duplex, auto-negotiation
100 Mbps Full/half duplex, auto-negotiation
1000 Mbps Full duplex
NOTE:
•
When 10/100 Mbps and half duplex/full duplex are specified for an Ethernet copper port, the
Ethernet copper port operates in forced mode. When 1000 Mbps is specified or the interface
speed and the duplex mode are not simultaneously specified for an Ethernet copper port, the port
operates in auto-negotiation mode.
•
When operating in forced mode, an Ethernet copper port does not support auto MDI/MDI-X.
•When operating in auto-negotiation mode, an Ethernet copper port supports auto MDI/MDI-X.
Interface cables
The HIM-4GBE/HIM-8GBE uses a category-5 straight-through or crossover Ethernet cable when
operating at 10/100 Mbps, and uses a category-6 cable (recommended) when operating at 1000
Mbps. For the appearance and connection of a HIM-4GBE/HIM-8GBE interface cable, see
"Connecting an Ethernet interface cable."
HIM-4GBP/HIM-8GBP
The HIM-4GBP and HIM-8GBP are high-speed Layer 3 GE interface modules. A HIM-4GBP
provides 4, and a HIM-8GBP provides 8 Small Form-Factor Pluggable (SFP) ports that support
Layer 3 routing. Each port is provided with a bi-color LED, which indicates the running status of the
port. Connected to the processor through an SPI-4 high-speed bus, the HIM-4GBP or HIM-8GBP
provides a full range of high-performance functions of Layer 3 Ethernet interfaces.

5
Front panels
Figure 4 Front panel of HIM-4GBP
(1) Captive screw
(2) SFP port
(3) SFP port status LED
(4) Ejector lever
Figure 5 Front panel of HIM-8GBP
(1) Captive screw
(2) SFP port
(3) SFP port status LED
(4) Ejector lever
LEDs
Table 5 LED description
LED status
Description
Off No link is present.
Steady green A 1000 Mbps link is present.
Flashing green The interface is receiving or sending data at 1000 Mbps.
Steady yellow A 100 Mbps link is present.
Flashing yellow The interface is receiving or sending data at 100 Mbps.
4
132
3
2
4
1

6
Interface specifications
Table 6 Interface specifications
Item
Specification
Connector type SFP
Number of interfaces •HIM-4GBP: 4
•HIM-8GBP: 8
Interface standards 802.3, 802.3u, 802.3ab
Supported frame
format
•Ethernet_II
•Ethernet_SNAP
Interface speed •1000 Mbps (recommended)
•Full duplex
The following transceiver modules are available for the HIM-4GBP/HIM-8GBP:
•
100 Mbps fiber SFP transceiver modules.
•
1000 Mbps fiber SFP transceiver modules.
•
100/1000 Mbps fiber SFP transceiver modules.
•
10/100/1000 Mbps copper SFP transceiver modules (support for 10/100/1000 Mbps
autosensing on the HIM-4GBP/HIM-8GBP).
Prepare the transceiver modules yourself as required.
As a best practice, use H3C SFP transceiver modules for the device. H3C does not guarantee the
compatibility of SFP transceiver modules from other vendors with the device. The device reports an
alarm when non-H3C SFP transceiver modules are installed.
Interface cables
Use interface cables for the HIM-4GBP/HIM-8GBP as follows:
•
Fiber SFP transceiver module—Fibers with the LC connector.
•
Copper SFP transceiver module—Category-5 straight-through or crossover twisted pair
cable when the port is operating at 10/100 Mbps and Category-6 twisted pair cable when the
port is operating at 1000 Mbps.
For the appearance and connection of a HIM-4GBP/HIM-8GBP interface cable, see "Connecting an
Ethernet interface cable" or "Connecting an optical interface cable."
HIM-1EXP
The HIM-1EXP is a 1-port 10 GE transceiver module. It provides one 10-Gigabit Small Form-Factor
Pluggable (XFP) port and supports switchover between LAN/WAN PHY modes. A LED is provided
on the front panel to show the operation state.

7
Front panel
Figure 6 Front panel
(1) Captive screw
(2) Ejector lever
(3) XFP port
(4) XFP port carrier signal LED (LINK/ACT)
LED
Table 7 LED description
LED status
Description
Off No link is present.
Steady green A link is present, but no data is being received or transmitted.
Flashing green The XFP port is receiving or sending data.
Interface specifications
Table 8 Interface specifications
Item
Specification
Connector type XFP/LC
Number of interfaces 1
Supported frame format 10GBASE-R/W
Interface speed •LAN PHY mode: 10.3125 Gbps
•WAN PHY mode: 9.95328 Gbps
NOTE:
In LAN PHY mode, 10GBASE-R is supported. In WAN PHY mode, 10GBASE-W is supported.
Interface cables
The HIM-1EXP must work with an XFP transceiver module and an optical fiber with LC-type
connectors. For the appearance and connection of a HIM-1EXP interface cable, see "Connecting an
optical interface cable."
HIM-CL1P/HIM-CL2P
The HIM-CL1P and HIM-CL2P are high-speed OC-3/STM-1 (155 Mbps) channelized packet over
SONET/SDH (CPOS) E1/T1 interface modules. The HIM-CL1P provides one SFP port and the port
1
4 3 2

8
is provided with two LEDs, which indicate the port running status and fault detection status,
respectively. The HIM-CL2P provides two SFP ports.
The HIM-CL1P/HIM-CL2P has the following features:
•
Connects to the processor through a 10-Gbps high-speed bus. Each CPOS interface can be
channelized into 63 E1s or 84 T1s, and it can be channelized into 512 DS0s.
•
Receives multiplexed E1/T1 circuits on a pair of fibers through a channelized interface, saving
many link resources, the occupied area, and the cost of local networks and devices for
telecommunication service providers and large enterprises.
•
Supports IP and MPLS traffic and the Multi-link Point-to-Point Protocol (MP), and supports up to
12 E1s or T1s in each MP bundle.
•
Uses hardware-based MP bundling. This solves the problem of low efficiency of MP bundling,
and improving the access density of user devices.
•
Supports two operating modes that can be configured at the CLI: CPOS E1 and CPOS T1.
•
The operating mode configuration takes effect only after you hot-swap the interface module or
reboot the device. As a best practice, remove and insert the module to bring the configuration
into effect.
•
Before removing a HIM interface module during device operation, execute the remove
command for the module.
•
The operating mode configuration takes effect for all the interfaces on the interface module.
NOTE:
•
The HIM-CL1P/HIM-CL2P does not support cascading and non-channelized SDH and SONET.
•The HIM-CL1P/HIM-CL2P does not support channelizing OC-3/STM-1 into DS3s or E3s.
Front panels
Figure 7 Front panel of HIM-CL1P
(1) SFP port carrier signal LED (LINK/ACT)
(2) SFP port loopback/alarm LED (LP/AL) of SFP port
(3) SFP port
(4) Captive screw
(5) Ejector lever
43
2
1
5

9
Figure 8 Front panel of HIM-CL2P
(1) SFP port carrier signal LED (LINK/ACT)
(2) SFP port loopback/alarm LED (LP/AL)
(3) SFP port
(4) Captive screw
(5) Ejector lever
LEDs
Table 9 LED description
LED
Status
Description
LINK/ACT
(Green)
Off No link is present.
On A 155.52 Mbps link is present.
Flashing The SFP port is receiving or sending data at 155.52 Mbps.
LP/AL
(Yellow)
Off No loopback or alarm exists.
On The port is in loopback state.
Flashing There is a minimum of one alarm.
Interface specifications
Table 10 Interface specifications
Item
Specification
Connector type SFP/LC
Number of interfaces •HIM-CL1P: 1
•HIM-CL2P: 2
Interface standards SONET OC-3/SDH STM-1
Interface speed 155.52 Mbps
Interface cables
The HIM-CL1P/HIM-CL2P must work with an SFP transceiver module and an optical fiber that have
LC-type connectors. For the appearance and connection of a HIM-CL1P/HIM-CL2P interface cable,
see "Connecting an optical interface cable."
2
13 4
5

10
HIM-CLS1P/HIM-CLS2P
The HIM-CLS1P and HIM-CLS2P are high-speed OC-3/STM-1 (155 Mbps) CPOS E3/T3 interface
modules. They can also operate in packet over SONET/SDH (POS) mode. The HIM-CLS1P
provides one SFP port and the port is provided with two LEDs, which indicate the port running status
and fault detection status, respectively. The HIM-CLS2P provides two SFP ports.
The HIM-CLS1P/HIM-CLS2P has the following features:
•
Connects to the processor through a 10-Gbps high-speed bus. Each OC-3/STM-1 POS
interface can be channelized into three E3s or T3s.
•
Each E3/T3 channel supports the subrate processing capability, providing users with a variety
of bandwidth options.
•
Receives multiplexed E3/T3 circuits on a pair of fibers through a channelized interface, saving
many link resources, the occupied area, and the cost of local networks and devices for
telecommunication service providers and large enterprises.
•
Supports IP and MPLS traffic and MP with up to three E3s or T3s in each MP bundle.
•
Supports three operating modes that can be configured at the CLI: CPOS E3, CPOS T3, or
POS (155 Mbps).
•
The configuration of the operating mode can take effect only after you hot-plug the interface
module or reboot the device. It is recommended to remove and insert the module to bring the
configuration into effect.
•
Before removing a HIM interface module during device operation, execute the remove
command for the module.
•
The configuration of the operating mode takes effect for all the interfaces on the interface
modules.
NOTE:
The HIM-CLS1P/HIM-CLS2P does not support channelizing OC-3/STM-1 into DS1s or E1s.
Front panels
Figure 9 Front panel of HIM-CLS1P
(1) Captive screw
(2) Ejector lever
(3) SFP port
(4) SFP port carrier signal LED (LINK/ACT)
(5) SFP port loopback/alarm LED (LP/AL)
3 2
1
4
5

11
Figure 10 Front panel of HIM-CLS2P
(1) Captive screw
(2) Ejector lever
(3) SFP port
(4) SFP port carrier signal LED (LINK/ACT)
(5) SFP port loopback/alarm LED (LP/AL)
LEDs
Table 11 LED description
LED
Status
Description
LINK/ACT
(Green)
Off No link is present.
On A 155.52 Mbps link is present.
Flashing The SFP port is receiving or sending data at 155.52 Mbps.
LP/AL
(Yellow)
Off No loopback or alarm exists.
On The interface is in loopback state.
Flashing There is a minimum of one alarm.
Interface specifications
Table 12 Interface specifications
Item
Specification
Connector type SFP/LC
Number of interfaces •HIM-CLS1P: 1
•HIM-CLS2P: 2
Interface standards SONET OC-3/SDH STM-1
Interface speed 155.52 Mbps
Interface cables
The HIM-CLS1P/HIM-CLS2P must work with an SFP transceiver module and an optical fiber with
LC-type connectors. For the appearance and connection of a HIM-CLS1P/HIM-CLS2P interface
cable, see "Connecting an optical interface cable."
1
3 2
4
5

12
HIM-MSP2P/HIM-MSP4P
The HIM-MSP2P/HIM-MSP4P is a high-speed OC-3/STM-1 (155 Mbps) and OC-12/STM-4 (622
Mbps) non-channelized POS interface module. The HIM-MSP2P/HIM-MSP4P supports PPP, Frame
Relay, and HDLC at the data link layer and IP at the network layer.
When using the HIM-MSP2P/HIM-MSP4P, follow these guidelines:
•
You can use the card-mode command to configure the interface module to operate in
OC-3/STM-1 POS or OC-12/STM-4 POS mode.
•
The configuration of the operating mode can take effect only after you hot-swap the interface
module or reboot the device. It is recommended to remove and insert the module to bring the
configuration into effect.
•
Before removing a HIM interface module during device operation, execute the remove
command for the module.
•
The configuration of the operating mode takes effect for all the interfaces on the interface
module.
•
The interface module supports multi-mode short distance (1310 nm), single-mode medium
distance (1310 nm), single-mode long distance (1310 nm), and single-mode ultra-long distance
(1550 nm) transceiver modules.
NOTE:
The HIM-MSP2P/HIM-MSP4P is an optional interface module to be separately ordered if needed.
Front panels
Figure 11 Front panel of HIM-MSP2P
(1) Captive screw
(2) Ejector lever
(3) SFP port carrier signal LED (LINK/ACT)
(4) SFP port loopback/alarm LED (LP/AL)
(5) SFP port 1 (155 Mbps)/SFP port 0 (622 Mbps)
(6) SFP port 0 (155 Mbps)
26
3
4
5
1

13
Figure 12 Front panel
(1) Captive screw
(2) Ejector lever
(3) SFP port carrier signal LED (LINK/ACT)
(4) SFP port loopback/alarm LED (LP/AL)
(5) SFP port 3 (155 Mbps) or SFP port 1 (622 Mbps)
(6) SFP port 2 (155 Mbps) or SFP port 0 (622 Mbps)
(7) SFP port 1 (155 Mbps)
(8) SFP port 0 (155 Mbps)
LEDs
Table 13 LED description
LED
Status
Description
LINK/ACT
(Green)
Off No link is present.
On A 155.52/622.08 Mbps link is present.
Flashing The SFP port is receiving or sending data at 155.52/622.08 Mbps.
LP/AL
(Yellow)
Off No loopback or alarm exists.
On The port is in loopback state.
Flashing There is a minimum of one alarm.
Interface specifications
Table 14 Interface specifications
Item
Specification
Connector type SFP/LC
Number of interfaces •HIM-MSP2P: 2 OC-3 interfaces or 1 OC-12 interface
•HIM-MSP4P: 4 OC-3 interfaces or 2 OC-12 interfaces
Interface standards •SONET STS-3/STS-12
•SDH STM-1/STM-4
Interface speed 155.52/622.08 Mbps
Interface cables
The HIM-MSP2P/HIM-MSP4P must work with an SFP transceiver module and an optical fiber with
LC-type connectors. For the appearance and connection of a HIM-MSP2P/HIM-MSP4P interface
cable, see "Connecting an optical interface cable."
2
3
4
5
1
7
8 6