H3C S12500-X Parts list manual

Manual version: 6PW102-20170411 BOM: 3123A0T2
i
H3C S12500-X LST1FW3B1 Card Manual
1 Card identifier
The card identifier LST1FW3B1 is at the upper right corner of the front panel.
2 Introduction
The LST1FW3B1 card provides one console port, one CF card interface, two USB interfaces, two
10/100/1000BASE-T Ethernet copper interfaces, and two Gigabit Combo interfaces.
You can use a combo interface to provide the following functions:
•In-band management.
•Outgoing interface for log messages.
•Failover interface for stateful failover.
3 Specifications
Figure 1 Front panel
(1) Console port (CONSOLE)
(2) USB ports (hardware reserved, software not support currently)
(3) 10/100/1000BASE-T copper combo port
(4) 10/100/1000BASE-T copper combo port LED (LINK/ACT)
(5) 1000BASE-X fiber combo port (6) 1000BASE-X fiber combo port LED (LINK/ACT)
(7) Alarm LED (ALM) (8) System LED (RUN)
(9) Ejector lever (10) Captive screw
Table 1 Card specifications
Item S
p
ecification
Flash 8 MB NOR flash, 16 bit wide
SDRAM
DDR3 SDRAM
2 slots for SDRAMs
Standard configuration: 16 GB (two 8 GB DDR3 SDRAMs)
Two same-sized DDR3 SDRAMs are required.
CF card One built-in CF card slot
256 MB CF card, expandable to 1 GB

Manual version: 6PW102-20170411 BOM: 3123A0T2
ii
Item S
p
ecification
Dimensions (H × W × D) 40.1 × 399.2 × 512 mm (1.58 × 15.72 × 20.16 in)
Power consumption 190 to 260 W
Weight 5.8 kg (12.79 lb)
Hot swapping Supported
Ports
•1 console port
•2 USB ports ((not supported by the card software)
•2 combo interfaces, which can operate in 10/100/1000BASE-T copper
port mode or 1000BASE-X SFP fiber port mode at a time.
You can use the combo enable { copper | fiber } command to activate either
port. By default, the copper combo port is activated.
Ambient temperature
•Operating: 0°C to 45°C (32°F to 113°F)
•Storage: –40°C to +70°C (–40°F to +158°F)
Ambient humidity
•Operating: 5% RH to 95% RH, noncondensing
•Storage: 5% RH to 95% RH, noncondensing
Compatible device models •H3C S12500-X series switches
System software version See the release notes that come with the card.
Table 2 Console port specifications
Item S
p
ecification
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
•Provides connection to an ASCII terminal.
•Provides connection to the serial port of a local or remote (through a pair
of modems) PC running terminal emulation program.
•Supports command line interface (CLI)
Table 3 10/100/1000BASE-T copper port specifications
Item S
p
ecification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Supported cable Category-5 (or above) twisted pair cable
Transmission distance 100 m (328.08 ft)
Port transmission rate
•10 Mbps, half/full duplex
•100 Mbps, half/full duplex
•1000 Mbps, full duplex

Manual version: 6PW102-20170411 BOM: 3123A0T2
iii
Table 4 1000BASE-X fiber port specifications
Item S
p
ecification
Transceiver module SFP
Connector type LC
Interface standard 802.3, 802.3u, and 802.3ab
Operating mode 1000 Mbps, full duplex
Table 5 1000BASE-X SFP port specifications
Gigabit SFP module Central
wavelength
Connector Cable specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A 850 nm LC 62.5/125μm
multi-mode optical fiber 0.55 km (0.34 miles)
SFP-GE-LX-SM1310-A 1310 nm LC 9/125 μm single-mode
optical fiber 10 km (6.21 miles)
SFP-GE-LH40-SM1310 1310 nm LC 9/125 μm single-mode
optical fiber 40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 nm LC 9/125 μm single-mode
optical fiber 40 km (24.86 miles)
SFP-GE-LH80-SM1550 1550 nm LC 9/125 μm single-mode
optical fiber 80 km (49.71 miles)
SFP-GE-LH100-SM1550 1550 nm LC 9/125 μm single-mode
optical fiber 100 km (62.14 miles)
4 LEDs
The card provides LEDs to show the operating status of the card and interfaces.
Table 6 LED description
LED Status Descri
p
tion
Alarm LED (ALM)
Off The system is operating correctly.
Steady red
The system is in an alarm condition, and immediate
action is required.
To identify the problem, use the system log.
System LED (RUN)
Off No power is input, or the card is faulty.
Steady green The system is not operating correctly.
Flashing green (1 Hz) The system has started up and is operating correctly.
Flashing green (8 Hz) The system is loading the software or is not ready.
Combo interface LED
(LINK/ACT)
Off No link is present on the port.
Steady green A link is present on the port.
Flashing green The port is sending or receiving data.

Manual version: 6PW102-20170411 BOM: 3123A0T2
iv
5 Installing and removing the card
CAUTION:
•Wear a well-grounded ESD wrist strap or ESD gloves before you install or remove the card.
•Do not touch the components on the PCB.
5.1 Installing the card
1. Remove the filler panel from the slot for the card at the front of the switch.
This example uses slot 7.
2. Place the card vertically with the surface-mounted components facing left. Pull the ejector levers
outward, and then gently push the card in along the slot guide rails until the card is in close contact
with the backplane.
3. Push the ejector levers inward.
4. Tighten the captive screws with a Phillips screwdriver to secure the card in the slot.
Figure 2 Installing the card
5.2 Removing the card
1. Use a Phillips screwdriver to loosen the captive screws at both sides of the card.
2. Pull the ejector levers at both sides of the card outward to separate it from the backplane, and then
pull the card along the guide rails to remove it from the chassis.

Manual version: 6PW102-20170411 BOM: 3123A0T2
v
3. Place the card on an anti-static workbench with the surface-mounted components up. You can also
put it in an anti-static bag.
4. If you are not going to install a new card, install a filler panel to prevent dust and ensure good
ventilation in the switch.
6 Logging in to the card
The card uses an independent operating system. Before you can configure the card, you must log in to
the card by using one of the following methods:
•Log in from the switch's CLI through the oap connect command.
•Log in through the card's Web, console port, or Telnet.
H3C recommends that you log in to the card from the switch's CLI the first time you access the card. This
section includes a procedure for logging in from the switch's CLI. For more information about other login
methods, see H3C SecPath Series High-End Firewalls Configuration Guides.
To log in to the card from the switch's CLI, perform the following task in user view:
Task Command Remarks
Log in to the card through OAP.
•In standalone mode:
oap connect slot slot-number
•In IRF mode:
oap connect chassis
chassis-number slot
slot-number
To return to the CLI interface of the
switch, press Ctrl+K.
7 Software upgrade
The card uses independent BootWare and system software images. You must upgrade the card software
separately from the switch software. To ensure a successful card upgrade, H3C recommends that you
upgrade the card through the card's console port or management Ethernet port. For more information
about software upgrade of the card, see the release notes that come with the card.
8 Obtaining documentation
To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:
1. Go to http://www.h3c.com.hk/Technical_Documents.
2. Click Security Products, and then choose the desired product.
Copyright © 2017 New H3C Technologies Co., Ltd.