H3C S5500-SI Series Installation instructions

H3C S5500-SI Series Ethernet Switches
Command Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: 20071208-C-1.01

Copyright © 2007, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care, , TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www. h3c.com
Technical Support
[e-mail]
http://www. h3c.com

About This Manual
Related Documentation
In addition to this manual, each H3C S5500-SI Series Ethernet Switches
documentation set includes the following:
Manual Description
H3C S5500-SI Complete Series
Ethernet Switches Installation Manual It provides information for the system installation.
H3C S5500-SI Series Ethernet Switches
Operation Manual It is used for assisting the users in data configurations and typical applications.
Organization
H3C S5500-SI Series Ethernet Switches Command Manual is organized as follows:
Part Contents
1 Login Introduces the commands used for logging
into an Ethernet switch.
2 VLAN Introduces the commands used for
configuring VLAN.
3 IP Address and IP Performance Introduces the commands used for
configuring IP address and IP
performance.
4 QinQ-BPDU TUNNEL Introduces the commands used for
configuring QinQ.
5 Port Correlation Introduces the commands used for configuring link aggregation and port
isolation.
6 Link Aggregation Introduces the commands used for link
aggregation.
7 MAC Address Table Management Introduces the commands used for
configuring MAC address forwarding table.
8 Port Security Introduces the commands used for port
security.
9 MSTP Introduces the commands used for
configuring MSTP.

Part Contents
10 IPv6 Introduces the commands used for
configuring IPv6 application.
11 IP Routing Overview Introduces the commands of Routing
Overview.
12 IPv4 Routing Introduces the commands used for
configuring IPv4 routing, static routing, RIP,
and route policy.
13 IPv6 Routing
Introduces IPv6 routing related
configurations, such as static routing,
RIPng, and route policy.
Introduces the commands used for
configuring IPv6 routing, static routing,
RIPng, and route policy.
14 Multicast Introduces the commands used for
configuring IGMP Snooping.
15 802.1x-HABP-MAC Authentication Introduces the commands used for 802.1x,
HABP and MAC related configurations.
16 AAA-RADIUS-HWTACACS Introduces the commands used for AAA,
RADIUS, HWTACACS, and the related
configurations.
17 ARP Introduces the commands used for
configuring ARP.
18 DHCP Introduces the commands used for DHCP
and the related configuration.
19 ACL Introduces the commands used for
configuring ACL.
20 QoS Introduces the commands used for
configuring QoS.
21 Port Mirroring Introduces the commands used for
configuring port mirroring.
22 UDP Helper Introduces the commands used for UDP
Helper and the related configuration.
23 Cluster Management Introduces the commands used for
configuring cluster.
24 SNMP-RMON Introduces the commands used for the configuration to manage network devices
through SNMP and RMON.
25 NTP Introduces the commands used for
configuring NTP.
26 DNS Introduces the commands used for
configuring DNS.

Part Contents
27 File System Management Introduces the commands used for file
system management.
28 Information Center Introduces the commands used for the
configuration to analyze and diagnose
networks using the information center.
29 System Maintaining and
Debugging Introduces the commands used for daily system maintenance and debugging.
30 NQA Introduces the commands used for
configuring NQA.
31 SSH Introduces the commands used for
configuring SSH2.0.
32 Track Introduces the commands used for
configuring Track.
33 PoE Introduces the commands used for
configuring PoE and PoE profile.
34 SSL-HTTPS Introduces the commands used for
configuring SSL and HTTPS.
35 PKI Introduces the commands used for
configuring PKI.
36 Stack Management Introduces the commands used for
configuring Stack Management.
37 Command Index Lists all the commands in this command
manual, which are arranged alphabetically.
Conventions
The manual uses the following conventions:
I. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.

Convention Description
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
# A line starting with the # sign is comments.
II. Symbols
Convention Description
Warning Means reader be extremely careful. Improper operation
may cause bodily injury.
Caution Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Note Means a complementary description.