Haag-Streit LENSTAR LS 900 User manual

INSTALLATION GUIDE
INSTALLATION GUIDE
LENSTAR LS 900
AND
LENSTAR LS 900 APS
Edition 3.10 / 2016-02

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
2© HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02
INSTALLATION GUIDE
LENSTAR LS 900
AND
LENSTAR LS 900 APS
Edition 3.10 / 2016-02
NOTES!
This manual is only intended for installation on LENSTAR LS 900 and LENSTAR LS 900 APS units.
This manual is only to be used by trained engineers that have attended an official HAAG-
STREIT training course.
Further important information:
Operation of the appliance for performance of an examination, as well as the description of the
EyeSuite software are described in a separate operating manual and can be called up in the
EyeSuite software using the 'F1' key.
Instructions regarding the function check can be found in the ‘Instructions for use’ (7220055).
‘EyeSuite Setup manual’ (7220060) regarding the installation of EyeSuite on a PC or laptop.
‘Instructions for use’ (7220055) regarding the purpose of use and description of the instrument.
Information on how to unpack and lift the device can be found in the ‘Instruction - unpacking
LENSTAR LS 900’(7220180).

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
© HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02 3
Contents
1. Safety Instructions....................................................................................................................................................... 4
1.1 Safety Instructions in text............................................................................................................................................... 4
2. Installation .................................................................................................................................................................... 4
2.1 Safe system configuration according to EN 60601-1..................................................................................................... 4
2.2 Sample configuration according to EN 60601-1 ............................................................................................................ 5
2.3 Mounting the roller rails/slide plate and cable connection ............................................................................................. 6
2.4 Instrument table (option) assembly.............................................................................................................................. 13
List of modifications.................................................................................................................................................. 14

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
4 © HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02
1. Safety Instructions
1.1 Safety Instructions in text
Safety instructions have been added throughout the text where applicable. They are classified according to
importance, and designed to help avoid risk to patients and operating staff, while preventing damage to the
LENSTAR LS 900 and LENSTAR LS 900 APS appliance and helping to ensure that it functions safely and remains in
perfect working order.
FORBIDDEN!
Neglecting these notes will lead to material damage and the endangering of users and patients.
WARNING!
These signs must be strictly adhered to, to ensure safe operation of the instrument and to avoid
endangering users and patients.
NOTE!
Important notes! Please read carefully.
2. Installation
2.1 Safe system configuration according to EN 60601-1
FORBIDDEN!
It is not permitted to make modifications to the measuring device.
WARNING!
The device must only be installed on a stable, horizontal surface.
All externally connected devices must comply with the standards relevant to safety.
NOTE!
After installation, a zero adjustment and function check must be performed in accordance with the
section "Function check".
The device should be set up in such a way that the plug is always easily accessible and the device
can easily be disconnected from the power supply.
During operation, the rail covers have to be mounted.

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
© HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02 5
2.2 Sample configuration according to EN 60601-1
1.) Power Supply LENSTAR (1020392) / LENSTAR APS (1022106)
2.) Laptop / PC
3.) Instrument Table
4.) Power Supply Laptop / PC
5.) Insulation transformer
6.) Printer
* med. approved EN 60601-1
** USB 2.0 or higher
1
2
3
4
6
5

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
6 © HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02
2.3 Mounting the roller rails/slide plate and cable connection
NOTE!
LS 900 manual cross slide covered in chapters 2.3.1 –2.3.3
LS 900 APS automated positioning system covered in chapters 2.3.4 –2.3.6
NOTE!
Clean the table surface before positioning the side identification sticker (LS 900 1021635 / LS 900
APS 1022151). Make sure that no oil and grease residue remains on the surface.
NOTE!
Function check and right/left recognition test must be performed after every
new installation
changes on the rail
changes of side identification sticker.
2.3.1 Roller rails/slide plate for LENSTAR LS 900 (not for LS 900 APS)
The roller rails/slide plate must be positioned in such a way, that when the device is centred, the patient’s eye will be
at a distance of 78 mm from the front of the device.
1.) Head rest columns
2.) Rail (1021435)
3.) Aperture for cables
4.) Side identification sticker* (1021635)
5.) Slide plate (1008386)
* The side identification sticker features a mounting aid to align it properly with the table edge if used in combination with a HS head rest Part
Number: 7200123
1
3
4
5
2

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
© HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02 7
2.3.2 Device connection, cables under the device for LENSTAR LS 900
The device can be invisibly wired by passing cables through the cross slide and using the cable channel underneath.
To do this, you need either the HAAG‑STREIT instrument table HSM 901 (option) or an aperture in the table-top
used.
Remove cable cover (1).
Expose USB and supply cables (2).
Insert the supply cable through the opening beneath the cross slide (3) until the cable emerges from the
opening at the top at the front.
Insert the USB cable through the same opening (3) on the cross slide.
Insert both cables in the appropriate box and fix with the tension compensator (4).
Mount the cable cover.
Mount the rail covers (1021914).
Figure 1 Figure 2
Figure 3 Figure 4

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
8 © HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02
2.3.3 Device connection, cables at side (option) for LENSTAR LS 900
Remove cable cover (5).
Expose USB and supply cables (left or right aperture on table).
With a knife, cut carefully into the snap-off point provided on the left or right of the cable cover (6).
Carefully use fingers to snap off the cut part (7).
Use a spiral wrap or the black tube (1003686) to join the USB and supply cable together (8).
Insert both cables in the appropriate box and fix with the tension compensator.
Mount cable cover.
Mount the rail covers (1021914).
Figure 5 Figure 6
Figure 7 Figure 8

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
© HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02 9
2.3.4 Roller rails and slide plate for LENSTAR LS 900 APS
The roller rails/slide plate must be positioned in such a way that when the device is centred, the patient’s eye will be
at a distance of 78 mm from the front of the device.
NOTE!
Set of table fittings for LS 900 APS (1022328) include:
2x Rails long (1021435)
2x Countersunk screw 4x20 (3000464)
2x Countersunk screw 4x12 (3000204)
2x Arrestor (1022317)
1x Rail cover complete (1021562)
1x Rail cover (1021556)
1x Magnetic slide plate (1022332)
1x Side identification sticker (1022151)
NOTE!
Clean the table surface before positioning the side identification sticker (1022151). Make sure that no
oil and grease residue remains on the surface.
WARNING!
The aperture of the cables has to be cut free form the side identification sticker with a sharp knife.
Ensure that there are not white or reflecting edges when doing so.
1.) Rail (1021435)
2.) Aperture for cables
3.) Side identification sticker* (1022151)
4.) Slide plate (1022332)
5.) Arrestor (1022317)
6.) Warning sticker “Do not use height adjustment without instrument in place”
* The side identification sticker features a mounting aid to align it properly with the table edge if used in combination with a HS head rest Part
Number: 7200123.
1
3
2
4
5
6
2

LENSTAR LS 900 / 900 APS | INSTALLATION GUIDE
10 © HAAG-STREIT AG, 3098 Koeniz, Switzerland –HS-Doc. No. 7220553 - Edition 3.10 / 2016-02
2.3.5 Device connection, cables under the device for LENSTAR LS 900 APS
The device can be invisibly wired by passing cables through the cross slide and using the cable channel underneath.
To do this, you need either the HAAG‑STREIT instrument table HSM 901 (option) or an aperture in the table-top
used.
Remove the rail covers.
Place the LENSTAR APS on the left side (seen form the joystick).
Expose USB and supply cables (table aperture, 9). The free cable length should not exceed 150mm.
Connect the supply and USB cable to the LENSTAR as seen in image 10.
Secure the connectors and cables as shown in image 11 using standard cable binders. Make sure that the
flaps are not mounted downwards, as they may drag on the table otherwise.
Place the LENSTAR on the rails; make sure that the free cable can move smoothly in the aperture. Check that
the LENSTAR can move free. If the LENSTAR can’t move correct in all directions, adjust the free cable length
until the LENSTAR can move evenly.
Mount the rail covers.
Figure 9
Figure 10 Figure 11